Showing results for 
Search instead for 
Did you mean: 

Cisco CyberSecurity


Forum Posts

I am trying to set up a L2L VPN between a Cisco ASR1k and a Draytek 2920 router (don't ask! :-)The VPN is failing to build with the following error on the ASR side:Sep 14 18:40:31.124 BST: IPSEC(ipsec_process_proposal): proxy identities not supported...

mmelbourne by Contributor
  • 1 replies
  • 0 Helpful votes

I am setting up EasyVPN with multipule branches to 2 headends. One headend as primary and the other as secondary. In the branch router I am using DPD for failover. Is there a way to control the fail back timer or manual fail back?Here is the scenario...

joe.ho by Beginner
  • 12 replies
  • 0 Helpful votes

Hi,I've just setup the basic configuration of IPSec remote access VPN on our Cisco ASA 5510 using the ASDM's VPN wizard. I was able to connect to the VPN connection however I was unable to ping, telnet, ssh and etc to any devices and servers in the i...

5y5tadmin by Beginner
  • 1 replies
  • 0 Helpful votes

Hi,We have 2x Asa5520 in failover with version 8.3.1.We configured the ssl vpn clients connections, once connected they will use the ASA Internet connection (no split tunneling).The problem is that even if we have a 5mbps ISP connection the clients a...

acleri by Beginner
  • 7 replies
  • 0 Helpful votes

Hello,I am configuring an ASA 5505 for remote users to access a network. VPN users can authenticate against the domain controller, connect and obtain a vaild IP. The local DNS server is resolving domain names for the users as well and the remote user...

I thought an SSL VPN would be good but everytime I go to connect to it I have click through security warnings and install a securty certificate. Other than that the VPN works, however there will be less tech savy (and paitent) users using this vpn, a...

jsandau by Beginner
  • 37 replies
  • 0 Helpful votes

We have internal VPN cluster based on 2 ASA-5520.From inside Cisco networks everything is fine MAC  and Windows AnyConnect clients (v2.5 or v3.0) can connect to it.From otside:MAC with IPSEC client v4.9 nad AnyConnect v2.5 and 3.0 works fineWindows I...

anlyakho by Beginner
  • 3 replies
  • 0 Helpful votes

Is it possible to segment site-to-site VPN traffic to different output interfaces on the ASA platform.  I would like to direct site-to-site VPNs from partners to a different interface than site-to-site VPNs from corporate sites.

I just had a third party vendor setup a Cisco ASA 5500 series.  I haven't figured out how to setup the Anyconnect on two of my 64-bit clients. One is on Windows 7 and one on Vista.  Eveverything works fine with 32-bit clients.Is there a specific sett...

mzoeller32 by Beginner
  • 1 replies
  • 0 Helpful votes

Recently installed ASA 5500.  Right now I have just a handful of users using the VPN.  However when they connect it asks for their network password, but when their password changes I need to make the change in the firewall first.  Is there a setting/...

Hi forumMy question is very simple. At my office we have a Cisco 1811 router that is connected to our internal network. Dialer0 is connected to our ISP. We have a IPSEC tunnel running between one of the branch offices at a different location. Our 181...

Hi AllI've just remoted into an 1841 router to set up a VPN but found to my surprise no commands available to set it up, ie. crypto isakmo policy n and the following  subsequent commands are not available. Checking the flash there seems to be all the...

Had anyone done a anyconnect and active directory setup. Still a little lost. I got the vpn working fine with ldap and staff can login fine. My next task is to get them to get there drive mappings. What would be the easiest or most common way of doin...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers