I need help. I'm trying to setup a VPN group on my 2811 router with advanceSECi thought that i could use my pix config but it's not working help
I need help. I'm trying to setup a VPN group on my 2811 router with advanceSECi thought that i could use my pix config but it's not working help
I'm running acs version 4.0, is there a way to force a password reset, as a user logs on.
The Cisco 5510 has a fixed IP address, but the Linksys BEFSX41 does not. I'm planning to use the Cisco/Linksys as a replacement for a pair of ZyWall 10 VPN routers. The ZyWall's allow me to specify (on the fixed IP end) the FQDN of the dynamic IP end...
Dear friends,I'm trying to configure an IPSec tunnel between an IOS router and a PIX v7.0. I've already seen some URLs here pointing to an example of configuration. However, that example covers only the v6.x version of PIX, not being useful to solve...
Hi all,could you please explain me what is meant of Dmz & Dmz 1 Normal (Not-Monitored)?ThanksAsa5540# sh failover Failover On Failover unit SecondaryFailover LAN Interface: failover GigabitEthernet0/3.1 (up)Unit Poll frequency 1 seconds, holdtime 15 ...
Hi,I'm trying to configure a new ASA 5510, the show version output show the activation key being used is not valid. Also I'm not able to perform the "setup" command too....Im getting the follwoing error...ciscoasa(config)# setupNo inside interface. ...
Hi everyone,does somebody knows how to configure a pix/asa and/or a router to do admission control for the vpn clients that connects?Thanks
I have an issue at my company and I need some ammunition to fight the battle between the Cisco side and the Microsoft side.Currently our company has aprox 500 clients VPN sessions connected to our Cisco 3030 Concentrators at any given time. We are e...
First, I'm not Bilingual so excuse my English.PVDM2-12DM, etcIs there a schedule that can be used by the BRI interface?Note: These digital modem modules must operate in conjunction with a T1/E1 Primary Rate Interface (PRI).http://www.cisco.com/en/US/...
hello, i have configured the client vpn on pix 515E and the user can connect successfully but they don't get any internal access to any servers also cannot browse internet.my config is attached
I have an ASA5540 that is in use as a VPN endpoint. I have both LAN to LAN and remote access VPN clients connecting to it. For the past 3 months it will randomly just drop all VPN packets. All other traffic will pass as it is supposed to, but no V...
Hello I am trying to determine what is the maximum VPN throughput achieved by a 3725 router with AIM-VPN/EPII-PLUS IPSec accelerator module. I have two routers connected back-to-back using a cross-over cable. An IPSec VPN tunnel is established betwee...
I am attaching ASA configuration and debuging crypto error.please look in to my matter and revert me back ASAP
Hello, guys. After updating from 12.2(37) -GD- on 7200 to a 12.3(22) only peers on Frame relay links are able to terminate IPSec tunnels to this 7200. The routers connected to the metroE cannot. If we go back and boot with the 12.2(37) the problem d...
Hello folks -We have a Cisco PIX 515E (6.3) that users VPN into. The PIX is at our main site, and we have 2 branch sites connected to the main site via point-2-point leased lines. Our main site address is 10.0.0./24, and one of our branch sites addre...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-19-2024 08:08 AM | ||
04-18-2024 10:47 AM | ||
04-17-2024 06:49 AM | ||
04-16-2024 07:12 AM | ||
04-14-2024 06:53 AM |
User | Count |
---|---|
7 | |
4 | |
1 | |
1 | |
1 |