VPN

Hi,I have a LAN-to-LAN VPN between ASA boxes connecting to private networks 192.168.1.0 and 10.10.10.0. All traffic between them should be allowed. Do I need to configure an explicit ACL that permits all traffic to be passed from 192.168.1.0 to 10.10...

Hi,We are anticipating one problem regarding VPn tunnel formation. We are using 3845 router dedicated for VPN termination on it's ethernet port.We anticipate we will be having 600 VPN tunnels which will terminate on this router. Plus we plan to have ...

Hello, I currently have an ASA5510 test setup using the physical inside interface (10.0.1.X) as a management network and a VLAN inside subinterface (192.168.0.X) network as the corporate LAN. I currently VPN into the ASA5510 to access both networks b...

I have seen this discussion before, but I dont think the scenarios were well played out and thoroughly discussed.Would it not be better to get a router with lets say 5 DSL interfaces and then Multilink those together than buying a T1. The 5 DSL line...

I have this schema: CompanyA CompanyB inIP:192.168.2.0 192.168.1.0 exIP:aaa.bbb.107.96 xxx.yyy.97.34/28 I need to configure site tosite VPN between but something is wrong. I?ll appreciate any help.The vpn for ...

I have a PIX 515E running 7.02 with an IPSEC VPN to a Cisco 2821 router. Both sides show that phase 1 and phase 2 are completed. My compnany owns the PIX. The ASDM vpn monitor shows the connections, (IKE, IPSec), are both up and even if I clear the s...

Hi,I want to configure an ISDN backup with a 1721 router, but I want to do it using the 2 BRI to get a backup of 265 Kb with the 4 b=channel.I don-t find the command necessary to do it.Thanks a lot

I have a Catalyst 3750 Metro running 12.2(25)EY4 on site A and a 2811 running 12.3(11)T4 on site B. There is an MPLS backbone in between and a GRE tunnel configured from site A to site B. At site B there are several hosts receiving multicast flows fr...

Hi all,I'm having trouble getting password changes to work with Cisco ACS 3.2, VPN 3015 and the Cisco VPN Client. I have some users configured in ACS to authenticate against or Windows Database. This works fine until their passwords expire (every 30 ...

Hi all!Our clients need web server that work for inside and outside. How to make it right? When you open port from DMZ to INSIDE this is potentialy unsafe. How to make this safe ? :)

Hi all,I have a vpn with checkpoint ngx r62 ,anybody know why all of my cisco routers notify every 15 minutes this message:%CRYPTO-6-IKMP_MODE_FAILURE: Proccessing of quick mode failed with peer at X.X.X.XTU

I am working on a design to use VPN to backup a frame relay network. I am using GRE tunnels to pass the traffic back and forth when the frame relay network is unavailable, using the "Backup Interface" command on the frame-relay sub interface. Thi...

Hi,We have currently deployed VPN 3060's in our network to support VPN clients. We are considering to start supporting SSL VPN Clients. (not WebVPN - Clientless). I'm trying to find how many concurrent SVC's supported by VPN 3060. In Concentrator Pro...

I coonect to vpn concentrator by vpn client 4.8.01 version.But some application doesn't work. Ping works fine but i cannot connect to own applications (example i can ping Lotus Notes server but i cannot send/receive email). Other client connected to ...

I have a full T1 that is currently going to a Cisco 1721 router s0 but I would like to get rid of the router and put the concentrator in its place. T1 is only used from the outside by client vpn but it also allows internet access from inside.Any help...