VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Any one succesfully deploy Remote VPN using the above configuration in particular V6.3.4. I am having problem where client losing conneciton and think it is related to bug CSCef17703 " Premature invalid SPI with dynamic crypto map" but not 100% sure...

tin.ngo by Level 1
  • 360 Views
  • 4 replies
  • 0 Helpful votes

I have looked through the posts and thought I found my solution. Unfortunately, I am still no go. I am trying to connect to a Checkpoint VPN concentrator and my peer requires me to NAT my traffic to an external address. Here is my config (I hope y...

cselledge by Level 1
  • 310 Views
  • 1 replies
  • 0 Helpful votes

Hi to all,is is posible to create an ip local pool within the same subnet of my lan?The reason for this is that one of those devices has a default gateway different than my vpn device and I am not allowed to change the setup for that particular devic...

d.robles by Level 1
  • 394 Views
  • 2 replies
  • 0 Helpful votes

We are are having some problems getting the tunnel to completely come up. It seems the IKE or Phase 1 completes and then Phase 2 won't complete. I am getting a message about INVALID_ID_INFO and the the process ends and restarts. I have attached th...

With well over 150 lan-to-lan VPN tunnels configured, I can usually get the tunnels up. However, this one is stumping me, unless the ISP is giving wrong information. Using a Cisco 871 router on-site and a Cisco 3005 concentrator in my data center, ...

hajoca by Level 1
  • 521 Views
  • 2 replies
  • 0 Helpful votes

We have a 515E with 64MB RAM that has been working fine with two tunnels configured out of it. Recently we attempted to add an additional tunnel and this caused all the tunnels to start dropping packets. We confirmed that this was the new tunnel by...

Hi,Does anyone know of a VPN module that supports AES for a cisco 3640? We currently have the AIM-VPN/MP installed, but it only supports DES/3DES. Is the AIM-VPN/HPII-PLUS compatible with a 3640?thanks,

Does anyone can tell me, or point me the right direction to find out about, what is/was the purpose of the command "crypto isakmp ccm".?I need to explain it to a customer, and I cannot find any information about it. I checked every 12.x command refer...

arielroza by Level 1
  • 3894 Views
  • 1 replies
  • 0 Helpful votes

Hi,I am a programmer working in Los Angeles, CA. my company allowed me to work through VPN while i am in india for sometime but now they say there could be legal issues of using VPN outside the united states of America.my company uses licensed versio...

sunkarikk by Level 1
  • 1835 Views
  • 3 replies
  • 0 Helpful votes

Hi all...I have set up my asa accepting vpn clients in from outside... My clients get their adresses from a pool 192.168.22.0/24.ip local pool VPN_CLIENT_POOL 192.168.22.1-192.168.22.255 mask 255.255.255.0Then I have a net that are behind another rou...

jenseike by Level 1
  • 494 Views
  • 3 replies
  • 0 Helpful votes

I am trying to figure out how to keep my users from accessing other Intenet connections, but must use the VPN to use the TCP/IP stack. In other words, how can I enable the Laptops to be able to work off line, but if they require TCP/IP (Networking) t...

bsoth by Level 1
  • 316 Views
  • 1 replies
  • 0 Helpful votes

Hello,I set up a VPN between these two devices and it comes up OK, and stays up for a while...however, it justs drops for no reason. And just the interface (Tunnel6) goes down, the actual crypto session stays up. All I have to do is a "clear crypto...

Hi all,could someone help me what is bestsolution to connect Central and remote sites together with ISDN T1/E1?Could someone help me with how to config this and give me any advice?Thanks a lot.BRjl

johnleeee by Level 1
  • 345 Views
  • 5 replies
  • 0 Helpful votes