Hello,someone can help please.I try to establish an IPSEC tunnel towards a Barracuda but so far no success. I can not send any data in the tunnel. They are all dropped Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0Outbound: #pkts enc'ed 0 drop 288 ...
Forum Posts
I am trying to setup FlexVPN with AnyConnect on a cisco C1117 router running version 16.12.03, but can't get it to work.I've been following both the official Cisco guide and some other config examples. Both the router and VPN profile should be correc...
Hi all..This was working fine until yesterday morning.. since then I am not able to browse internet it I am connected to VPN.. I get a 'Page cannot be displayed' error message.. the second I disconnect from VPN, I am able to browse internet.. I have...
Hi All, So let's say i have a basic AnyConnect configuration on the Outside interface.Now i'm connected with AnyConnect and got a IP from the ip local pool, let's say: 192.168.100.100. If i want to do a packet trace on the ASA to verify ACL's and...
Resolved! How to setting easyvpn please help
I can't search easyvpn setting wayhow can I do this? Setting easyvpn R3Server: Server0 RadiusYou will PC15 do connect R6 from easyvpnGroup name: skillsGroup key: skillsusername: easyvpnpassword: cisco123 pool: 10.0.0.1~10.0.0.100/24 Example
I am a trying to get Anyconnect to work on my Windows 10 desktop. The config works fine on my laptop. The config should permit a split tunnel, but on my desktop, when AnyConnect is started, internet access is blocked and no traffic traverses the tu...
Hiplease help resolving the following issue. We are facing the problem with the following:-IKEv2-PSK-dVTI tunnel mode ipsec- tunnel src in vrfOn the far end non-cisco (DIGI Transport WR44) devices are establishing the IPsec successfully, and the fol...
Maybe this has been requested and I could not find the post but we have a 24 hr time limit on VPN connections, one feature that would be great is maybe 10 mins before that time out if anyconnect could have the feature of "I'm still connected" almost ...
Hi everyone, We're building a new IPsec tunnel in my company and I wanted to know why we would use NAT over this VPN. I know that is useful for overlapping subnets but in our case it is not the case. So in what could be helpful. Thank in advance. Reg...
Hi, Just seeking some help and guidance as we are running RA VPN on ASA 5512 with users authenticated via ISE posturing policies, we prefer to build a parallel FTD so for now ASA and FTD will be running parallel for same RA VPN. Slowly and steadily ...
Hi Guys, Have a question around FTD radius failover on 6.6 version * Even if we configure retry timer interval to 1 second , it takes around 3-4 seconds to failover to the secondary radius server - is this the expected behaviour ? * Once the primary ...
I have a package where only VPN and Umbrella is included. When installing on New mac´s it works fine On existing Mac´s and I try to run same package, the installation overview just shows that the "umbrella roaming security" is "skipped" - But why ??I...
Can someone explain the difference between L-AC-APX-LIC= Cisco AnyConnect Apex Term License, Total Authorized Usersand L-AC-APX-3Y-S2 Cisco AnyConnect Apex License, 3YR, 100-249 Users ? or it is the same license just with the difference of the expira...
I ran across this scenario last week and I am not sure if I am missing something simple or if this is a real issue.Problem: It appears IP6 may interfere with IP4 VPN connections.My network is a large state-wide network which touches many other state ...
Hello, I tried generating RSA key using 2048 bits on switch model : WS-C3560CX-8PC-S But after saving the configuration and I type sh ssh, I still get :- Minimum expected Diffie Hellman key size : 1024 bits
