I've configured VPN between Cisco VPN Client on W2K and Cisco 1721 with RADIUS (according to example on Cisco web-site). It works fine. But then I set on Cisco "crypto map <clientmap> local-address Loopback N". After that VPN Client hungs up on "...
i have PIX 506EI successfuly configured for VPN access users via IPSec/UDP. And they can access to LAN. But when i choose in Cisco VPN Client v4 transport IPSec/TCP -it's failed to connect.Here config-..access-list outside_cryptomap_dyn_30 permit ip ...
We are planning on setting up another site containing a rack to house some servers. My boss wants as many servers as possible to be put on this rack so there is less space used at our main location. I'm assuming we will just set up a site-to-site v...
I have two sites using the 4.0.2 client and both of them are having realy bad lag time issues. One of them is running Great Plains localy with the ODBC mapped. And the other is running QuickBooks with the qbt. file mapped. Even when using the client ...
Hello,I am having problems connecting my pix to my ca server==status=0 failed to open a http connection.The ca server is running on a SuSE 9.0 box. The ca isTinyCA. What is the cgi-bin dir/file that the pix is looking for?Thank you!
First, while I'm not new to networking or Cisco routers, I'm new to PIX/VPN.I've been using version 6.3 of the Cisco PIX firewall and VPN configurationguide. While there is a lot of information in the guide, I've found it tobe cumbersome and difficu...
Hi everyone,I have two networks, and the side A, I have a router connected in a Ethernet1/0 in a ADSL provider equipment, and my configuration is working ok, without problems.But I would like to know, how I can configure a VPN peer to peer, with anot...
I have PIX 501 ver 6.3(1) and it is configure only for EZVPN. I like to configure this PIX also for WEBVPN or SSLVPN. I am now sure that if this PIX501 supported this feature. If someone have any information and like to share I will really appricate.
Hello together,we have an connection between a outside router (836) to a Router in the HQ (7204VXR) via L2TP using PPPoE.This is working fine. Now we like to configure IPSec between the two Routers. We have used the configuration that Cisco provides ...
I currently have out PIX configured to have 3 of our locations terminating to it. What I am trying to figure out is if you can allow all of the locations to access the internet without using split tunnel?Currently I am having a ahrd time grasping how...
Hello,I have a 2691 router and I am connecting to it with Cisco VPN client 4.0.3E for Mac OSX.I am able to connect and authenticate but I am unable to access any computers on the network.The only thing I can ping is the loopback 127.0.0.1. I disabled...
I'm a newbie to setting up devices for VPN, and need some direction. Currently on our network we have several remote locations that use Netopia dial-up routers to VPN into our Netscreen appliance at headquarters. We're trying to move away from that a...
v1.1 or 1.1aThere is a radio button available in the wizard mode, but always grayed up. And how to understand message "Easy VPN server configuration on this router is not supported trough SDM" There is no any info in documentation. Is it supported or...
Has anyone used the 3rd (external) interface on the VPN conc as a public interface? If so can I set up a separate IP pool for the users to grab an IP address from? If I were to set up multiple DHCP scopes (one for each interface) where do those sub...
I have dual pix's configured for stateful failover. If and when a fialover change occurs the active PIX has no IPSEC and ISAKMP security associations active and the remote end (an 831) thinks it still has an active tunnel. At the remote end I have to...
