I have replaced the cables and the Cisco ASA 5505, I still lose packets whenI ping a pc on the other end of the site to site IPsec vpn tunnel. Can someonetell me if this is related to the configuration of Cisco ASAs or other networkingproblems. Th...
Dears ... please, there is any book or video that can you provide me to understand the ikev2 ?as well there is any template can i use ? to configure itplease asap cuz it's required from me in my work thanks
Dears i confugre the below on my ASA access-list ACL_PROXY_ACL extended permit ip 10.10.10.10 255.255.255.255 44.44.44.44 255.255.255.255 ! crypto ipsec ikev1 transform-set TSET_TO_BRANCH esp-aes 256 esp-sha256-hmac ! crypto map CMAP_VPN 10 mat...
Question : when I am trying to ping IP Loopback IP or Router 3 from Router 2 then i am unable to ping it. Even on router R1 unable to ping se 1/3 13.1.1.1/24. Below are configuration or all three routers. Router 1***********interface Loopback...
I am experiencing an issue with the 'show sessions' command. I wanted to test out the 'show session' and 'show users' commands just to see it work properly. However, after starting a Telnet session from one switch (SW1) through the default gateway an...
Hi, I have a query that i hope someone would be able to clear up and correct my understanding if wrong. We're currently running GETVPN over Hub/spoke MPLS. The branches/spokes currently have no access to the internet, however now there is a need f...
Hi Guys, We currently have 2 Datacenters, but for management we only have 1 AnyConnect entry. Now we're looking into bringing in some redundancy for our AnyConnect VPN and we found the Backup Server. Now i might be missing something here, but i couln...
Can I configure a VTI tunnel (the new routing type) so the destination can come from a dynamic address (i.e. where the remote device, in my case a router, has a DHCP assigned address)? I have tried various ways so far without success. I can get a...
We are seeing an install problem with the AnyConnect Secure Mobility Client under Windows 7. The installer stalls after a minute or so then reports:There is a problem with this Windows Installer package. A program run as part of the...
Hello.I'm connecting to corporate LAN via AnyConnect from my laptop. I get an assigned ip address like 192.168.88.11. Is it possible to ping my IP address (88.11) from ASA or from inside corporate LAN?
Hello, I have configured RADIUS Authentication by Windows Server 2016. It seems to be work: test aaa-server authentication NPS host 10.254.1.211 username vpn pa$ INFO: Attempting Authentication test to IP address <10.254.1.211> (timeout: 12 seconds...
Hi everybody! I created 10 vpn on asa 5525 but when creating vpn 11 it can't. it is show run : !interface GigabitEthernet0/0 nameif inside security-level 100 ip address 192.168.100.1 255.255.255.0 ! interface GigabitEthernet0/1 nameif ou...
I am the a middle of setting up an ipsec-vpn with ikev2. but my tunnel-group ipsec attributes will not accept ikev2 command. Please refer to the output below: ------------------------------------------------------------------ Data-FW(config)# tunne...
Hello , I need to make ipsec connections from an ASR902 router. In the release notes one states IPSEC tunnel is only supported on ASR903 and ASR907 ; Anyway the commnands are in the CLI . Anyone knows if IPSEC is possible on the ASR902? ...
My title says it all.Is there anyway to have AnyConnect access the machine certificate store on Windows 7 without requiring the AnyConnect application run as admin?Is there some setting to override this requirement? in the profile xml, through window...
.jpg "VIP Master"){kind=icon}
