Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
I'm try to connect two ASAs together using the following config, but unable to get it to work. Can someone let me know what I'm doing wrong?
ASA-1
crypto ikev2 policy 1 encryption aes-256 integrity sha512 group 14 prf sha512 lifetime seconds 864...
I am setting up a new site to site IPSec on Cisco IOS router.
The phase 1 and 2 both show up but the tunnel interface goes down in 4 seconds.
*Nov 16 17:16:45.400: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel2, changed state to up*Nov 16 1...
Hi,
i have cisco ASA 5506-X running with ASA 9.3(2) and ASDM 7.3(3)
i am not able to find the client-server plug-ins for ssh and RDP so that i can use them with clientless ssl vpn access.
I found for a higher series 55xx on ciscos site ssh.12.21.20...
Hi,
i have cisco ASA 5506-X running with ASA 9.3(2) and ASDM 7.3(3)
i am not able to find the client-server plug-ins for ssh and RDP so that i can use them with clientless ssl vpn access.
I found for a higher series 55xx on ciscos site ssh.12.21.20...
Hi,
I have a scenario with two routers, two ASA 5515X and two ISP. I need to configure load balancing so that site to site tunnel traffic should follow ISP 1 and rest of the traffic should follow ISP2 and all the traffic with one either of the ISP in...
Hello,
I'm having some errors with setting up a site to site VPN between my ASA 5510 and a clients 3845 Router. I keep getting the behaviour such that the phase 1 of the VPN session stays established for about 32 seconds, disconnects and automaticall...
Folks,
How best can we get a backup done for the Anyconnect nodes? The basic configuration is fine as a output of the show runnning file is sufficent. My question is more on the DAP policies side. These are not stored in the show running.
Thanks,
N.
Just a quick question.Setting up a VTI between two endpoints and I want to know best practises.
Should the transform set NAME match? My testing shows this is OK to not have the same name on either end as the tunnel works great.
Should the ipsec pro...
Hi. I'm having some trouble with my VPN connection where I can connect to it fine, and get internet access, but I cannot access the internal LAN. Does anyone have any thoughts on what I can check to resolve that?
Dear all:
I'm tryng to make a VPN between a RV110W to an ASA 5520. I configured the devices as follow:
ASA 5520# sh verCisco Adaptive Security Appliance Software Version 9.1(6)6 Device Manager Version 7.3(1)101Compiled on Wed 03-Jun-15 17:19 by bu...
hi,we encounter a problemon a IPsec VPN (ikev2) with Certificat on Firewall ASA, it remains up for 5 seconds and then Delet IKE SA.NB: the IPsec VPN ikev2 is between a the Firewall ASA and a Firewall FortIgate.
On the ASA Side we have :
IKEv2-PLAT-...
I'm working with a CSR 1000v, trying to connect to a Linux machine with strongSwan. If I enable ESN on the strongSwan system, I see the tunnel is not established because the Cisco isn't proposing any use of ESN.
Does IOS provide the capability to e...
I'm working with a CSR 1000v, trying to connect to a Linux machine with strongSwan. If I enable ESN on the strongSwan system, I see the tunnel is not established because the Cisco isn't proposing any use of ESN.
Does IOS provide the capability to e...
Hi Everyone,
I have some problem in the site to site connection for call. here i give the topology
the yealink phone in site B is register to the server in site A using the public ip, when i try register using the local IP the phone not register,
...
