VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Resolved! IKE phase 1

Existing config on ASA 5510:crypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption aes-256 hash sha group 5 lifetime 86400=====i want to create another site to site vpn, the second site also using the same (pre-share,...

Hi there,I've just attempted to configure a test site to site VPN. Diagram of arrangement is attached. Router R2 is supposed to act like the 'Internet' just to allow connectivity between both networks.My VPN configs on ASA1 and ASA2 are below:ASA1acc...

Hi, Can I employ 2 Cisco ASA 5512-X firewalls for AnyConnect Clustering with Certs in an active/active setup?Clustering - perhaps this is not the correct term, but I basically need to have an active/active AnyConnect setup with load distribution and ...

fsebera by Level 4
  • 498 Views
  • 2 replies
  • 0 Helpful votes

Trying to create VPN site to site between ASA5300 & Cisco 881C, but tunnel is not getting up.On ASA 5300:crypto isakmp enable outsidecrypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400crypto ipsec transfor...

FRasuli01 by Level 1
  • 639 Views
  • 4 replies
  • 0 Helpful votes

Hello,It looks like one of our customers need to buy ISR's to connect to the Azure cloud from Microsoft via DMVPN, since Cisco ASA doesn't support it (yet).Will ASA support this in nearby future release?Anybody has eventually suggestions? (Apart from...

erwee1973 by Level 1
  • 1637 Views
  • 1 replies
  • 0 Helpful votes

I have an implementation of anyconnect vpn on a c1941 that has been running good for win7 clients on anyconnect client version 3.1.04066.  I upgraded the win7 client to win 8.1 and installed the anyconnect client 3.1.04072 and cannot establish link. ...

mialbert by Level 1
  • 4086 Views
  • 4 replies
  • 0 Helpful votes

hello all,Could someone please recommend a stable AC client version?Our endpoint clients are Win7 & Mac OSX 10.10 (Yosemite)It looks like v3.1 & v4.0 are the latest versions available for download.Does v4.0 use the new licensing model, or can we stil...

huangedmc by Level 3
  • 831 Views
  • 1 replies
  • 0 Helpful votes

Hi,I'm a bit confused as to which software VPN clients are still supported etc:Cisco Secure DesktopSSL ClientsAnyConnect v3 However SSL Clients and CSD haven't been updated for a year to couple of years now. I found a depreciation notice regarding CS...

edw by Level 1
  • 948 Views
  • 7 replies
  • 0 Helpful votes

Hi All,I need to create a remote access vpn tunnel to a cisco 866VAE-k9 (interfaceport GE0).i have tried multiple configuration options like i found them in the documentation, but wasn't able to get it to work. the current setup is:866VAE-k9 LAN ip: ...

ingvar001 by Level 1
  • 369 Views
  • 0 replies
  • 0 Helpful votes

Hi, I would like to verify my setup. If this is achievable in terms of IPSEC HA failover.Apparently the VPN headend is a 3925ISR.Primary link to remote sites will be via ISP 1 Direct lease line.If any of the lease line to/fro the remote site breaks, ...

has anyone setup a site to site vpn tunnel with Anyconnect access to one of the sites using 8.4 code?i have done it several times with 8.2 code but am missing something with 8.4.I get connected with the client, but cannot access internal resources.an...

1snelson by Level 4
  • 292 Views
  • 1 replies
  • 0 Helpful votes