VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

my vpn is connected good on my windows but no ping from windows to any ip in routerthis is my config Current configuration : 7138 bytes!! Last configuration change at 03:16:48 UTC Wed Jul 27 2022!version 16.12service timestamps debug datetime msecser...

zsmo2372 by Beginner
  • 163 Views
  • 0 replies
  • 0 Helpful votes

interface Virtual-Template down status down protocolei try to create vpnbut in i set this command show ip int brife interface Virtual-Template is down status down protocole how i can make it upthis vpn is not workign good . no ping for any ipCurrent ...

Untitled.png
zsmo2372 by Beginner
  • 3548 Views
  • 66 replies
  • 0 Helpful votes

we have the problem when logging in to Cisco Anyconnect that after the user login a c. 5 minute host scan follows and the 2FA query does not come at all. After that, the connection will be terminated. The same user can easily log into another machine...

Amen by Beginner
  • 119 Views
  • 0 replies
  • 0 Helpful votes

Hi everyone,I'm trying to configure a dynamic authorization on the FMC, and when I enabling this feature ( Objects - AAA Server - RADIUS Server Group) then click Save, an error prompted "Following AAA server doesnt have connectivity configured to int...

denisT96 by Beginner
  • 162 Views
  • 0 replies
  • 0 Helpful votes

Hello,we have FTDs managed via FMC running ver 7.0. Recently, the ISP scan found a vulnerability on the outside interface of the FTD having weak a DH primes set. I updated the configuration for SSL DH group to: group14 (2048modulus) the highest  avai...

Hello,Please assist me on one of the issues I am facing when performing Source NAT on FTD's IPsec VTI tunnel. Is this supported or am I missing something that needs to be addressed before NAT? Our goal is to achieve load-balancing of inter-region tra...

SourceNAT.PNG

Dear Community, I have issues below and can't figure out why my Phase2 is not coming up, even my router and the remote end has the same transform set settings. Below is the log in phase 2. My router is 5.5.5.5 , remote is 3.3.3.3. The remote peer is ...

Hi,I test site site vpn between ASA & cisco router with GNS3, topology is basic the tunnel is up but the issue when ping remote host from both sides there are icmp drops, show command on both router and ASA don't include droppings. below is a sample ...

egyptology by Beginner
  • 2978 Views
  • 3 replies
  • 0 Helpful votes

Having an issue where the spoke and reach the hub and vice versa. But NHRP can't register and create a session. Any ideas? dmvpn-hub-csr1#show run int Tu1Building configuration...Current configuration : 386 bytes!interface Tunnel1bandwidth 1000000ip ...

JKOOP by Beginner
  • 773 Views
  • 10 replies
  • 0 Helpful votes

Hi,I am using anyconnect for remote acess , the authentication and anutorization done b ise , Now I want to do an additional layer of protection based on  certificate. The RA users are corporate and contractors ?How can I do the above Please help 

Can somebody help me.We have changed ASA 5512-X to FPR 2110. There is a IPSEC tunnel running on it.Here is the throughput with ASA5512-X one parallel flow. This is inbound to ASA5512-XEncryption Settings belowProtocol : IKEv1 IPsecEncryption : IKEv1:...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: