cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2766
Views
10
Helpful
7
Replies
Highlighted

Cisco 819 - Enable GPS

Hello,

I got a new 819, but I'm unable to activate GPS the way it's described in the documentation. 

Router(config-if)# do sh inv
NAME: "C819GW-LTE-GA-EK9", DESCR: "C819GW-LTE-GA-EK9 chassis, Hw Serial#:, Hw Revision: 6.0"
PID: C819GW-LTE-GA-EK9 , VID: V01 , SN:

NAME: "C819GWLTE Mother board on Slot 0", DESCR: "C819GWLTE Mother board"
PID: C819GW-LTE-GA-EK9 , VID: V01 , SN:

NAME: "Modem 0 on Cellular0", DESCR: "Sierra Wireless MC7304 4G-GA"
PID: MC7304 , VID: 1.0, SN:

This should be the command to activate:

controller cel 0

lte gps mode standalone

But this command isn't available:

Router(config-if)#controller cel 0
Router(config-controller)#lte ?
event              cellular snmp event persistence
failovertimer    Failover timeout value in mins
interface          Cellular interface
modem            Modem logging configuration
radio                Controller's radio
sim                  Subscriber Identity Module
sms                 SMS configuration

Router(config-controller)#lte

- Please rate helpful posts -
7 REPLIES 7
Highlighted
Advisor

This is what I see on a very

This is what I see on a very similar model router:

KFC-Balmoral(config-controller)#do show inv
NAME: "C887VAG-4G-GA-K9", DESCR: "C887VAG-4G-GA-K9 chassis

controller cellular 0 

#lte ?
event cellular snmp event persistence
failovertimer Failover timeout value in mins
gps GPS configuration
modem Modem logging configuration
radio Controller's radio
sim Subscriber Identity Module
sms SMS configuration

It is running this software image:

c800-universalk9-mz.SPA.154-3.M4.bin

Highlighted
Advisor

I just found an even closer

I just found an even closer matching router.

#show inv
NAME: "C897VAG-LTE-GA-K9", DESCR: "C897VAG-LTE-GA-K9 chassis

(config)#controller cellular 0

(config-controller)#lte ?
event cellular snmp event persistence
failovertimer Failover timeout value in mins
gps GPS configuration
modem Modem logging configuration
radio Controller's radio
sim Subscriber Identity Module
sms SMS configuration

It is running software image:

c800-universalk9-mz.SPA.154-3.M2.bin

Highlighted

Thanks for your reply.

Thanks for your reply.

The router was shipped with 15.5.3M, but I also updated to 15.6.1T0a for the test.

I just tried to boot 15.4, but it looks like it's not supported on that hardware:

*** No sreloc section!!!FATAL ERROR : Unknown controller type 3254!!!FATAL ERROR : Unknown controller type 3254

I think they changed something with that model/HW revision, but it's not documented anywhere...

- Please rate helpful posts -
Highlighted
Beginner

Hi Christian

Hi Christian

have same problem, cannot configure GPS (Feature enabled, State disabled, no command:

(config-controller)# lte gps enable
  • C819GW-LTE-GA-EK9
  • c800-universalk9-mz.SPA.155-3.M.bin

Did somebody solved this problem ?

Thank in advance

Highlighted

It's not a problem, it's just

It's not a problem, it's just not implemented by now. 

I was told that it should be available in this releases:

15.6(3) T

15.5(3)3M3

- Please rate helpful posts -
Highlighted
Beginner

:-O

:-O

Does it mean we cannot use GPS on these routers? 

I have another router

C819G-4G-G-K9 with c800-universalk9-mz.SPA.154-3.M1.bin and GPS commands where available :-S

Thank Christian, let me know 

Alberto

Highlighted
Advisor

What software version do you

What software version do you have?  I would be tempted to try the gold star release 15.4(3)M4 if you are running something less than this version.