Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1792
Views
20
Helpful
7
Replies

Help configuring Anyconnect

Go to solution
support
Level 1
Level 1

‎09-26-2012 10:01 AM - edited ‎02-21-2020 06:21 PM

I am trying to configure Anyconnect for the 1st time via the GUI, though I am comfortable with the command line if required.  I am familiar with PIX and IOS prior to 8.3 so this is my 1st time with newer versions. My equipment is in a lab environment at the moment but will be placed into production shortly.  I recieve the following errors when trying to establish an Anyconnect VPN connection with the local account on the ASA. Below is my config

anyconnect.jpg             

ASA Version 8.6(1)2

!

hostname TOR1PLXSD01

enable password sxZETAvnsVuPSnUc encrypted

passwd FomDbcd6ujnk.spR encrypted

names

!

interface GigabitEthernet0/0

description Management

speed 1000

duplex full

nameif Inside

security-level 100

ip address 172.21.20.1 255.255.255.0 standby 172.21.20.2

!

interface GigabitEthernet0/1

speed 1000

duplex full

no nameif

no security-level

no ip address

!

interface GigabitEthernet0/1.20

description Plexxus Data

vlan 20

nameif data

security-level 50

ip address 172.16.18.1 255.255.255.0 standby 172.16.18.2

!

interface GigabitEthernet0/1.25

description DMZ

vlan 25

nameif DMZ

security-level 25

no ip address

!

interface GigabitEthernet0/2

shutdown

no nameif

no security-level

no ip address

!

interface GigabitEthernet0/3

shutdown

no nameif

no security-level

no ip address

!

interface GigabitEthernet0/4

nameif Outside

security-level 0

ip address x.x.x.1 255.255.255.224 x.x.x.2

interface GigabitEthernet0/5

description LAN/STATE Failover Interface

!

interface Management0/0

nameif management

security-level 100

ip address 192.168.1.1 255.255.255.0

management-only

!

boot system disk0:/asa861-2-smp-k8.bin

ftp mode passive

dns domain-lookup data

dns server-group DefaultDNS

name-server 172.16.18.21

name-server 172.16.18.22

object network OBJ_INSIDE-HOSTS_172.21.20.0

subnet 172.21.20.0 255.255.255.0

object network OBJ_DATA-HOSTS_172.16.18.0

subnet 172.16.18.0 255.255.255.0

access-list acl_outside extended permit icmp any any

access-list acl_data extended permit icmp any any

access-list acl_inside extended permit icmp any any

access-list acl_dmz extended permit icmp any any

pager lines 24

logging enable

mtu Inside 1500

mtu data 1500

mtu DMZ 1500

mtu Outside 1500

mtu management 1500

ip local pool vpn_pool1 172.16.22.5-172.16.22.250 mask 255.255.255.0

ip local pool vpn_pool2 172.16.23.5-172.16.23.250 mask 255.255.255.0

failover

failover lan unit primary

failover lan interface Failover GigabitEthernet0/5

failover link Failover GigabitEthernet0/5

failover interface ip Failover 4.4.4.1 255.255.255.0 standby 4.4.4.2

icmp unreachable rate-limit 1 burst-size 1

icmp permit any Inside

icmp permit any data

icmp permit any DMZ

icmp permit any Outside

asdm image disk0:/asdm-66114.bin

no asdm history enable

arp timeout 14400

!

object network OBJ_INSIDE-HOSTS_172.21.20.0

nat (Inside,Outside) dynamic 68.71.198.102

object network OBJ_DATA-HOSTS_172.16.18.0

nat (data,Outside) dynamic 68.71.198.102

access-group acl_inside in interface Inside

access-group acl_data in interface data

access-group acl_dmz in interface DMZ

access-group acl_outside in interface Outside

route Outside 0.0.0.0 0.0.0.0 68.71.198.97 1

route data 172.16.5.0 255.255.255.0 172.16.18.3 1

route data 172.16.10.0 255.255.255.0 172.16.18.3 1

route data 172.16.13.0 255.255.255.0 172.16.18.3 1

route data 172.16.14.0 255.255.255.0 172.16.18.3 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

timeout floating-conn 0:00:00

dynamic-access-policy-record DfltAccessPolicy

user-identity default-domain LOCAL

aaa authentication ssh console LOCAL

http server enable

http 172.21.20.0 255.255.255.0 Inside

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart

telnet timeout 5

ssh 172.21.20.0 255.255.255.0 Inside

ssh timeout 5

console timeout 0

no vpn-addr-assign aaa

no vpn-addr-assign dhcp

dhcpd address 192.168.1.2-192.168.1.254 management

dhcpd enable management

!

threat-detection basic-threat

threat-detection statistics access-list

no threat-detection statistics tcp-intercept

webvpn

enable Outside

anyconnect-essentials

anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

anyconnect enable

group-policy AnyConnectClientPolicy internal

group-policy AnyConnectClientPolicy attributes

wins-server none

dns-server value 172.16.18.21 172.16.18.22

vpn-tunnel-protocol ikev2 ssl-client

default-domain value plexxus.ca

address-pools value vpn_pool1 vpn_pool2

username dmradmin password 1ZwOzoVS5TWIvR0h encrypted

tunnel-group AnyConnectClientProfile type remote-access

tunnel-group AnyConnectClientProfile general-attributes

default-group-policy AnyConnectClientPolicy

!

class-map inspection_default

match default-inspection-traffic

!

!

policy-map type inspect dns preset_dns_map

parameters

  message-length maximum client auto

  message-length maximum 512

policy-map global_policy

class inspection_default

  inspect dns preset_dns_map

  inspect ftp

  inspect h323 h225

  inspect h323 ras

  inspect rsh

  inspect rtsp

  inspect esmtp

  inspect sqlnet

  inspect skinny

  inspect sunrpc

  inspect xdmcp

  inspect sip

  inspect netbios

  inspect tftp

  inspect ip-options

!

service-policy global_policy global

prompt hostname context

no call-home reporting anonymous

Cryptochecksum:659360d147ccf882ab6cbb6e170ca8d2

: end

TOR1PLXSD01

    

ASA Version 8.6(1)2

!

hostname TOR1PLXSD01

enable password sxZETAvnsVuPSnUc encrypted

passwd FomDbcd6ujnk.spR encrypted

names

!

interface GigabitEthernet0/0

description Management

speed 1000

duplex full

nameif Inside

security-level 100

ip address 172.21.20.1 255.255.255.0 standby 172.21.20.2

!

interface GigabitEthernet0/1

speed 1000

duplex full

no nameif

no security-level

no ip address

!

interface GigabitEthernet0/1.20

description Plexxus Data

vlan 20

nameif data

security-level 50

ip address 172.16.18.1 255.255.255.0 standby 172.16.18.2

!

interface GigabitEthernet0/1.25

description DMZ

vlan 25

nameif DMZ

security-level 25

no ip address

!

interface GigabitEthernet0/2

shutdown

no nameif

no security-level

no ip address

!

interface GigabitEthernet0/3

shutdown

no nameif

no security-level

no ip address

!

interface GigabitEthernet0/4

nameif Outside

security-level 0

ip address 68.71.198.100 255.255.255.224 standby 68.71.198.101

!

interface GigabitEthernet0/5

description LAN/STATE Failover Interface

!

interface Management0/0

nameif management

security-level 100

ip address 192.168.1.1 255.255.255.0

management-only

!

boot system disk0:/asa861-2-smp-k8.bin

ftp mode passive

dns domain-lookup data

dns server-group DefaultDNS

name-server 172.16.18.21

name-server 172.16.18.22

object network OBJ_INSIDE-HOSTS_172.21.20.0

subnet 172.21.20.0 255.255.255.0

object network OBJ_DATA-HOSTS_172.16.18.0

subnet 172.16.18.0 255.255.255.0

access-list acl_outside extended permit icmp any any

access-list acl_data extended permit icmp any any

access-list acl_inside extended permit icmp any any

access-list acl_dmz extended permit icmp any any

pager lines 24

logging enable

mtu Inside 1500

mtu data 1500

mtu DMZ 1500

mtu Outside 1500

mtu management 1500

ip local pool vpn_pool1 172.16.22.5-172.16.22.250 mask 255.255.255.0

ip local pool vpn_pool2 172.16.23.5-172.16.23.250 mask 255.255.255.0

failover

failover lan unit primary

failover lan interface Failover GigabitEthernet0/5

failover link Failover GigabitEthernet0/5

failover interface ip Failover 4.4.4.1 255.255.255.0 standby 4.4.4.2

icmp unreachable rate-limit 1 burst-size 1

icmp permit any Inside

icmp permit any data

icmp permit any DMZ

icmp permit any Outside

asdm image disk0:/asdm-66114.bin

no asdm history enable

arp timeout 14400

!

object network OBJ_INSIDE-HOSTS_172.21.20.0

nat (Inside,Outside) dynamic 68.71.198.102

object network OBJ_DATA-HOSTS_172.16.18.0

nat (data,Outside) dynamic 68.71.198.102

access-group acl_inside in interface Inside

access-group acl_data in interface data

access-group acl_dmz in interface DMZ

access-group acl_outside in interface Outside

route Outside 0.0.0.0 0.0.0.0 68.71.198.97 1

route data 172.16.5.0 255.255.255.0 172.16.18.3 1

route data 172.16.10.0 255.255.255.0 172.16.18.3 1

route data 172.16.13.0 255.255.255.0 172.16.18.3 1

route data 172.16.14.0 255.255.255.0 172.16.18.3 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

timeout floating-conn 0:00:00

dynamic-access-policy-record DfltAccessPolicy

user-identity default-domain LOCAL

aaa authentication ssh console LOCAL

http server enable

http 172.21.20.0 255.255.255.0 Inside

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart

telnet timeout 5

ssh 172.21.20.0 255.255.255.0 Inside

ssh timeout 5

console timeout 0

no vpn-addr-assign aaa

no vpn-addr-assign dhcp

dhcpd address 192.168.1.2-192.168.1.254 management

dhcpd enable management

!

threat-detection basic-threat

threat-detection statistics access-list

no threat-detection statistics tcp-intercept

webvpn

enable Outside

anyconnect-essentials

anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

anyconnect enable

group-policy AnyConnectClientPolicy internal

group-policy AnyConnectClientPolicy attributes

wins-server none

dns-server value 172.16.18.21 172.16.18.22

vpn-tunnel-protocol ikev2 ssl-client

default-domain value plexxus.ca

address-pools value vpn_pool1 vpn_pool2

username dmradmin password 1ZwOzoVS5TWIvR0h encrypted

tunnel-group AnyConnectClientProfile type remote-access

tunnel-group AnyConnectClientProfile general-attributes

default-group-policy AnyConnectClientPolicy

!

class-map inspection_default

match default-inspection-traffic

!

!

policy-map type inspect dns preset_dns_map

parameters

  message-length maximum client auto

  message-length maximum 512

policy-map global_policy

class inspection_default

  inspect dns preset_dns_map

  inspect ftp

  inspect h323 h225

  inspect h323 ras

  inspect rsh

  inspect rtsp

  inspect esmtp

  inspect sqlnet

  inspect skinny

  inspect sunrpc

  inspect xdmcp

  inspect sip

  inspect netbios

  inspect tftp

  inspect ip-options

!

service-policy global_policy global

prompt hostname context

no call-home reporting anonymous

Cryptochecksum:659360d147ccf882ab6cbb6e170ca8d2

: end

Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
Javier Portuguez
Level 9
Level 9
In response to support

‎09-26-2012 11:19 AM

I am glad to hear you fixed it

Please check this out:

object network VPN_POOL

     subnet 192.168.1.0 255.255.255.0 --> adjust this to your real IP range

!

object-group network INTERNAL_NETWORKS_VPN

     object-network 192.168.2.0 255.255.255.0 ----> This is the internal network you want to reach across the tunnel.

!

nat (inside,outside) 1 source static INTERNAL_NETWORKS_VPN INTERNAL_NETWORKS_VPN destination static

VPN_POOL VPN_POOL route-lookup

That is pretty much the NAT Exempt on 8.3, 8.4, 8.6...

Further information:

ASA Pre-8.3 to 8.3 NAT configuration examples

Keep me posted.

Thanks.

Portu.

Please rate any helpful posts.

View solution in original post

7 Replies 7

Go to solution
Javier Portuguez
Level 9
Level 9

‎09-26-2012 10:33 AM

Hi Philippe,

Please make the following change:

tunnel-group AnyConnectClientProfile webvpn-attributes

     group-url https://x.x.x.1/test

!

Then, in the AC connect field, enter: x.x.x.1/test

Let me know if that works for you.

Most likely, this is your issue:

ASA SSL VPN Tunnel Group Group-URL and Group-Alias selection methods

Keep me posted.

Thanks.

Please rate any helpful posts

Go to solution
support
Level 1
Level 1
In response to Javier Portuguez

‎09-26-2012 11:06 AM

Thanks, 

I actually fixed it moments before your post.

I added

tunnel-group-list enable

tunnel-group AnyConnectClientProfile webvpn-attributes

group-alias AnyConnect enable

Seems that there is a check box in on the GUI that needs to be selected.  Under Anyconnect connection profiles , check off Allow user to select connection profile......otherwise DefaultWebVPNGroup will be the connection profile

Though I could use help configuring the no nat access_lists since I am not familiar with the commands in 8.6

I am use to

access-list no_nat extended permit  .....

nat (inside) 0 access-list no_nat

0 Helpful

Go to solution
Javier Portuguez
Level 9
Level 9
In response to support

‎09-26-2012 11:19 AM

I am glad to hear you fixed it

Please check this out:

object network VPN_POOL

     subnet 192.168.1.0 255.255.255.0 --> adjust this to your real IP range

!

object-group network INTERNAL_NETWORKS_VPN

     object-network 192.168.2.0 255.255.255.0 ----> This is the internal network you want to reach across the tunnel.

!

nat (inside,outside) 1 source static INTERNAL_NETWORKS_VPN INTERNAL_NETWORKS_VPN destination static

VPN_POOL VPN_POOL route-lookup

That is pretty much the NAT Exempt on 8.3, 8.4, 8.6...

Further information:

ASA Pre-8.3 to 8.3 NAT configuration examples

Keep me posted.

Thanks.

Portu.

Please rate any helpful posts.

Go to solution
support
Level 1
Level 1
In response to Javier Portuguez

‎09-26-2012 11:34 AM

I think I get it...

I want VPN users to access the "data" interface only, not the "inside"

I created

object network OBJ_DATA-HOSTS_172.16.18.0

subnet 172.16.18.0 255.255.255.0

object network OBJ_VPN_SUBNETS_172.16.22.0-172.16.23.255

range 172.16.22.0 172.16.23.255

nat (data,Outside) source static OBJ_DATA-HOSTS_172.16.18.0 OBJ_DATA-HOSTS_172.16.18.0 destination static OBJ_VPN_SUBNETS_172.16.22.0-172.16.23.255 OBJ_VPN_SUBNETS_172.16.22.0-172.16.23.255

Is this correct ? What does the "route-lookup" command do ?

0 Helpful

Go to solution
Javier Portuguez
Level 9
Level 9
In response to support

‎09-26-2012 11:41 AM

Hi Philippe,

Yes it looks great.

On the other hand:

route-lookup

(Optional) For identity NAT in routed mode, determines the egress interface using a route lookup instead of using the interface specified in the NAT command. If you do not specify interfaces in the NAT command, a route lookup is used by default.

http://www.cisco.com/en/US/docs/security/asa/asa84/command/reference/no.html#wp1792563

Please let me know if you have further questions, otherwise please mark this post as answered.

Thanks.

Go to solution
support
Level 1
Level 1
In response to Javier Portuguez

‎09-26-2012 12:25 PM

Thanks for all your help.  Got it working. 

Go to solution
Javier Portuguez
Level 9
Level 9
In response to support

‎09-26-2012 12:32 PM

Awesome

I hope you have a nice day.

0 Helpful
Customers Also Viewed These Support Documents