cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
165
Views
5
Helpful
3
Replies
Highlighted
Beginner

IKEv1 ASA to Router VPN S2S Phase 2 not working

Hi All,

I am trying to connect a cisco 4321 Router with Dynamic LTE IP to a static cisco 5506x ASA. When I create the tunnel statically it works 100%. But when I try to do dynamic on the ASA its complaining about: crypto map policy not found.

dst                             src                    state       conn-id status
ASAPUBLICIP ROUTERPUBLICIP MM_NO_STATE 1391 ACTIVE (deleted)

 

The router should be able to ping the network paste the ASA as well.

Attached is the config and debugs for both devices.

 

What am I missing in the configuration in order for it to work theres hardly any good examples for a dynamic router to vpn to a static ASA...

 

thanks for your help!

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted

oh Phase-2 Proposal Mismatch double check your ipsec transfrom-set value/configuration.

please do not forget to rate.

View solution in original post

3 REPLIES 3
Highlighted
VIP Advocate

on firewall you have access-list as

access-list ROUTER_VPN_ACL extended permit ip object-group LAN_NETWORKS object-group ROUTER_NETWORK

!

object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 172.160.0.0 255.240.0.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object object obj_any
object-group network ROUTER_NETWORKS
network-object 10.170.124.160 255.255.255.224

 

 

where as in your router acl you have define

!

ip access-list extended CMAP_ACL
permit ip any any

 

 

your access-list must have to be mirrior on both end as same.

please do not forget to rate.
Highlighted

Hi Sheraz,

I have set the two subnets as below would this

 

 

Router

ip access-list extended CMAP_ACL
permit ip 10.170.124.160 0.0.0.31 10.170.124.128 0.0.0.31

 

ASA

access-list ROUTER_VPN_ACL extended permit ip 10.170.124.128 255.255.255.224 object-group ROUTER_NETWORKS

 

but now I get on ASA:

 

Feb 23 2021 11:57:52: %ASA-3-713902: Group = DefaultL2LGroup, IP = ROUTERPUBLICIP, QM FSM error (P2 struct &0x00007f44b3516810, mess id 0x5e67a74e)!
Feb 23 2021 11:57:52: %ASA-3-713902: Group = DefaultL2LGroup, IP = ROUTERPUBLICIP, Removing peer from correlator table failed, no match!
Feb 23 2021 11:57:52: %ASA-3-713194: Group = DefaultL2LGroup, IP = ROUTERPUBLICIP, Sending IKE Delete With Reason message: Phase-2 Proposal Mismatch.
Feb 23 2021 11:57:52: %ASA-4-113019: Group = DefaultL2LGroup, Username = DefaultL2LGroup, IP = ROUTERPUBLICIP, Session disconnected. Session Type: LAN-to-LAN, Duration: 0h:00m:01s, Bytes xmt: 0, Bytes rcv: 0, Reason: Phase 2 Mismatch

 

Highlighted

oh Phase-2 Proposal Mismatch double check your ipsec transfrom-set value/configuration.

please do not forget to rate.

View solution in original post

Content for Community-Ad