cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
848
Views
1
Helpful
3
Replies
sharan
Beginner

Problem loading AIM-VPN/HPII on C3745

I tried latest mainline and T train with no success.  Getting the following errors on two identical 3745 routers with 2 identical AIM modules:

on 12.3

*Mar  1 00:01:07.419: %VPN_HW-1-INITFAIL: Slot 1: No ACK for command.., 0x80000000(50000 ms)

*Mar  1 00:01:07.419: %VPN_HW-1-INITFAIL: Slot 1: Making mini_omq failed: 00180010

*Mar  1 00:01:07.419: %VPN_HW-1-INITFAIL: Slot 1: microcode download failure

on 12.4

*Mar  1 00:01:09.995: %VPN_HW-1-INITFAIL: Slot 1: No ACK for command.., 0x80000000(50000 ms)

*Mar  1 00:01:09.995: %VPN_HW-1-INITFAIL: Slot 1: Making mini_omq failed: 00180010After mbox fail:

*Mar  1 00:01:09.995: register base address is: 3A800000

*Mar  1 00:01:09.995: versionid = 00140002

Any suggestions would be appreciated.

AIM Module in slot: 1

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-18028-01

        Board Revision           : C0

        Deviation Number         : 0-0

        Fab Version              : 03

        PCB Serial Number        : FOC08101AN8

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : AIM-VPN/HPII

        Version Identifier       : v01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 03 0B 41 01 00 C0 46 03 20 00 46 6C 01

*Mar  1 00:01:09.995: %VPN_HW-1-INITFAIL: Slot 1: No ACK for command.., 0x80000000(50000 ms)
*Mar  1 00:01:09.995: %VPN_HW-1-INITFAIL: Slot 1: Making mini_omq failed: 00180010After mbox fail:
*Mar  1 00:01:09.995: register base address is: 3A800000
*Mar  1 00:01:09.995: versionid = 00140002

1 ACCEPTED SOLUTION

Accepted Solutions
PAVEL SHEVELEV
Beginner

Check DRAM, I met this problem if memory modules have different capacity.

View solution in original post

3 REPLIES 3
PAVEL SHEVELEV
Beginner

Check DRAM, I met this problem if memory modules have different capacity.

View solution in original post

olpeleri
Cisco Employee

Hello,

Bad news: Hardware is end of support since 2012. See the URL below.

http://www.cisco.com/en/US/prod/collateral/routers/ps282/prod_end-of-life_notice0900aecd80444877.html

You should not try any new software on such kind of ancient device.... Most likely the support has been removed on latest code.

Cheers,

sharan
Beginner

Forgot about this posting, it's been a year.  I can confirm mismatching memory caused the issue for me as well, I should have posted a reply back then, sorry.

As far as out of support, yes, I think we all know this.  My car is from 2005, it's also out of support, I probably should replace that as well ;-/.

Content for Community-Ad