Router Cisco Soho 91 rebooting

[mocah]

Dear all,

today I have upgraded rommon in Cisco Soho 91 image to version 820_RM_ALT.srec.122-11r.YV4. Since then I have following messages when booting/restarting router:

**************************************************************

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

The ATU Switch reset isn't yet completed!

The PHY0 reset isn't yet completed!

The PHY1 reset isn't yet completed!

The PHY2 reset isn't yet completed!

The PHY3 reset isn't yet completed!

The PHY4 reset isn't yet completed!

C800/SOHO series (Board ID: 28-130) platform with 32768 Kbytes of main memory

************************************************************

Does somebody know what they mean and which command shoul I use to access rommon?

Thank you and kind regards,

M.

[Georg Pauwen]

Hello,

can you get into ROMMON (either press Ctrl + Break or Ctrl + C within 60 seconds after rebooting the device) ? If so, there should be a 'tftpdnld' command which allows you do download the IOS again...

Regards,

GP

[mocah]

Hello,

Unfortunately I can not. Router is constantly rebooting and all I can see now is:

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

Is there any other way to enter rommon?

[sarbjeet-dhillon]

Please find document below with various break sequences to try

http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080174a34.shtml

Please find document below to recover your router from rommon mode

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/826/swg/rommon.htm

[mocah]

It does not work I tried everything what is suggested on http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/826/swg/rommon.htm

Thank you kind regards,

M

[francoisenjeroen]

Hi!

Are you sure that "break" is enabled ?

If break is disabled, turn the router off ( O ), wait 5 seconds, and turn it on ( | ) again. Within 60 seconds, press the Break key. The terminal displays the ROM monitor prompt.

[mocah]

Hi,

I am not sure. Every time when I start router I get following message repeating it self every 5-10 seconds:

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.2(11r)YV4, RELEASE SOFTWARE (fc1)

Technical Support: »www.cisco.com/techsupport

Copyright (c) 2005 by cisco Systems, Inc.

Thank you and kind regards,

M.