cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
297
Views
0
Helpful
1
Replies
TL64
Beginner

Trouble connecting with an IPSEC tunnel in a Hub and Spoke model.

Hello everyone, I am currently working on a Hub and Spoke model network, connecting the branches with an IPSEC tunnel. ISAKMP turns on when I'm done configuring, but I can't seem to ping any other branch, or generate traffic between them. I've been troubleshooting this for a few days, but I could really use a new set of eyes. I'll attach the output of "show crypto ipsec" from my Hub(LA) and the configuration files for LA and the first branch SF.logical topologylogical topology Any help or push in the right direction would be greatly appreciated.

!!FW_LA_R
enable
configure terminal
hostname FW_LA_R
!
Int g0/0
Ip add 2.2.1.1 255.255.255.248
Ip nat outside
No shut
Int g0/1
Ip add 10.10.1.1 255.255.255.0
Ip nat inside
No shut
ip access-list extended IPSEC_LIST_SF
permit ip 10.10.0.0 0.0.255.255  10.20.0.0 0.0.255.255
permit ip 10.30.0.0 0.0.255.255 10.20.0.0 0.0.255.255
permit ip 10.128.0.0 0.0.255.255 10.20.0.0 0.0.255.255
ip access-list extended IPSEC_LIST_SD
permit ip 10.10.0.0 0.0.255.255  10.30.0.0 0.0.255.255
permit ip 10.20.0.0 0.0.255.255 10.30.0.0 0.0.255.255
permit ip 10.128.0.0 0.0.255.255 10.30.0.0 0.0.255.255
ip access-list extended IPSEC_LIST_NY
permit ip 10.10.0.0 0.0.255.255  10.128.0.0 0.0.255.255
permit ip 10.20.0.0 0.0.255.255 10.128.0.0 0.0.255.255
permit ip 10.129.0.0 0.0.255.255 10.128.0.0 0.0.255.255
ip access-list extended NAT_LIST
deny ip 10.10.0.0 0.0.255.255  10.20.0.0 0.0.255.255
deny ip 10.30.0.0 0.0.255.255 10.20.0.0 0.0.255.255
deny ip 10.128.0.0 0.0.255.255 10.20.0.0 0.0.255.255
!
deny ip 10.10.0.0 0.0.255.255  10.30.0.0 0.0.255.255
deny ip 10.20.0.0 0.0.255.255 10.30.0.0 0.0.255.255
deny ip 10.128.0.0 0.0.255.255 10.30.0.0 0.0.255.255
!
deny ip 10.10.0.0 0.0.255.255  10.128.0.0 0.0.255.255
deny ip 10.20.0.0 0.0.255.255 10.128.0.0 0.0.255.255
deny ip 10.129.0.0 0.0.255.255 10.128.0.0 0.0.255.255
!
permit ip 10.10.0.0 0.0.255.255 any



ip nat inside source list NAT_LIST int g0/0 overload
!
!
!
!
ip route 0.0.0.0 0.0.0.0 2.2.1.2
ip route 10.10.0.0 255.255.0.0 10.10.1.2
!
!! IPSec Phase 1

!
crypto isakmp enable
crypto isakmp policy 10
authentication pre-share
encryption aes 256
hash sha
group 5
crypto isakmp key ABC12345 address 2.2.2.1
crypto isakmp key ABC12345 address 2.2.3.1
crypto isakmp key ABC12345 address 4.4.128.1
! IPSec Phase 2
! IPSec Phase 2
crypto ipsec transform-set ABCSET esp-aes 256 esp-sha-hmac
crypto map ABCMAP 10 ipsec-isakmp
match address IPSEC_LIST_SF
set peer 2.2.2.1
set transform-set ABCSET
crypto map ABCMAP 20 ipsec-isakmp
match address IPSEC_LIST_SD
set peer 2.2.3.1
set transform-set ABCSET
crypto map ABCMAP 30 ipsec-isakmp
match address IPSEC_LIST_NY
set peer 4.4.128.1
set transform-set ABCSET
interface g0/0
crypto map ABCMAP
router ospf 1
default-information originate
network 10.0.0.0 0.127.255.255 area 0
network 10.128.0.0 0.127.255.255 area 0
!LA_3650
enable
configure terminal
hostname LA_3650
!
ip routing
vtp mode server
vtp domain MAIN
Vlan 99
name management
Vlan 10
name Server
Vlan 20
name IT
Vlan 30
name Users
interface G0/0
no switchport 
ip address 10.10.1.2 255.255.255.0
no shutdown
interface vlan 99
ip address 10.10.99.1 255.255.255.0
no shutdown
interface vlan 10
ip address 10.10.10.1 255.255.255.0
interface vlan 20
ip address 10.10.20.1 255.255.255.0
interface vlan 30
ip address 10.10.30.1 255.255.255.0
no shutdown
interface g0/1
switchport  mode access 
switchport  access  vlan 10
interface g0/2
switchport  mode access 
switchport  access  vlan 20
interface g0/3
switchport  mode access 
switchport  access  vlan 30
router ospf 1
network 10.0.0.0 0.127.255.255 area 0
network 10.128.0.0 0.127.255.255 area 0
!FW_SF_R
enable
configure terminal
hostname FW_SF_R
!
interface g0/0
ip address 2.2.2.1 255.255.255.252
ip nat outside
no shutdown
interface g0/1
ip address 10.20.1.1 255.255.255.0
ip nat inside
no shutdown
ip route 0.0.0.0 0.0.0.0 2.2.2.2
ip nat inside source list NAT_LIST interface g0/0 overload
ip access-list extended IPSEC_LIST

permit ip 10.20.0.0 0.0.255.255 10.10.0.0 0.0.255.255
permit ip 10.20.0.0 0.0.255.255 10.30.0.0 0.0.255.255
permit ip 10.20.0.0 0.0.255.255 10.129.0.0 0.0.255.255
permit ip 10.20.0.0 0.0.255.255 10.128.0.0 0.0.255.255
ip access-list extended NAT_LIST
deny ip 10.20.0.0 0.0.255.255 10.10.0.0 0.0.255.255
deny ip 10.20.0.0 0.0.255.255 10.30.0.0 0.0.255.255
deny ip 10.20.0.0 0.0.255.255 10.129.0.0 0.0.255.255
deny ip 10.20.0.0 0.0.255.255 10.128.0.0 0.0.255.255
permit ip 10.20.0.0 0.0.255.255 any
crypto isakmp enable
crypto isakmp policy 10
authentication pre-share
encryption aes 256
hash sha
group 5
crypto isakmp key ABC12345 address 2.2.1.1
crypto ipsec transform-set ABCSET esp-aes 256 esp-sha-hmac
crypto map ABCMAP 10 ipsec-isakmp
match address IPSEC_LIST
set peer 2.2.1.1
set transform-set ABCSET
interface g0/0
crypto map ABCMAP
router ospf 1
default-information originate
network 10.0.0.0 0.127.255.255 area 0
network 10.128.0.0 0.127.255.255 area 0
!SF_3650
enable
configure terminal
hostname SF_3650
!
ip routing
vtp mode server
vtp domain SF
Vlan 99
name management
Vlan 30
name Users
interface G0/0
no switchport 
ip address 10.20.1.2 255.255.255.0
no shutdown
interface vlan 99
ip address 10.20.99.1 255.255.255.0
no shutdown
interface vlan 30
ip address 10.20.30.1 255.255.255.0
no shutdown
interface g0/3
switchport  mode access 
switchport  access  vlan 30
router ospf 1
network 10.0.0.0 0.127.255.255 area 0
network 10.128.0.0 0.127.255.255 area 0
!FW_SD_R
enable
configure terminal
hostname FW_SD_R
!
interface g0/0
ip address 2.2.3.1 255.255.255.252
ip nat outside
no shutdown
interface g0/1
ip address 10.30.1.1 255.255.255.0
ip nat inside
no shutdown
ip route 0.0.0.0 0.0.0.0 2.2.3.2
ip nat inside source list NAT_LIST interface G0/0 overload
ip access-list extended IPSEC_LIST
permit ip any 10.0.0.0 0.127.255.255
permit ip any 10.0.0.0 0.127.255.255
ip access-list extended NAT_LIST
permit ip any 10.0.0.0 0.127.255.255
permit ip any 10.0.0.0 0.127.255.255
permit ip any any
crypto isakmp enable
crypto isakmp policy 10
authentication pre-share
encryption aes 256
hash sha
group 5
crypto isakmp key ABC12345 address 2.2.1.1
crypto ipsec transform-set ABCSET esp-aes 256 esp-sha-hmac
crypto map ABCMAP 10 ipsec-isakmp
match address IPSEC_LIST
set peer 2.2.1.1
set transform-set ABCSET
interface g0/0
crypto map ABCMAP
router ospf 1
default-information originate
network 10.0.0.0 255.128.0.0 area 0
network 10.128.0.0 255.128.0.0 area 0
FW_LA_R(config-router)#do show crypto ipsec sa

interface: GigabitEthernet0/0
    Crypto map tag: ABCMAP, local addr 2.2.1.1

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.129.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.128.0.0/255.255.0.0/0/0)
   current_peer 4.4.128.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 4.4.128.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:
          
     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.20.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.30.0.0/255.255.0.0/0/0)
   current_peer 2.2.3.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 2.2.3.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.30.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.20.0.0/255.255.0.0/0/0)
   current_peer 2.2.2.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 2.2.2.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.10.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.30.0.0/255.255.0.0/0/0)
   current_peer 2.2.3.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 2.2.3.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:
          
     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.10.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.20.0.0/255.255.0.0/0/0)
   current_peer 2.2.2.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 2.2.2.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.10.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.128.0.0/255.255.0.0/0/0)
   current_peer 4.4.128.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 4.4.128.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.20.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.128.0.0/255.255.0.0/0/0)
   current_peer 4.4.128.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 4.4.128.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.128.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.20.0.0/255.255.0.0/0/0)
   current_peer 2.2.2.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 2.2.2.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none
          
     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:

   protected vrf: (none)
   local  ident (addr/mask/prot/port): (10.128.0.0/255.255.0.0/0/0)
   remote ident (addr/mask/prot/port): (10.30.0.0/255.255.0.0/0/0)
   current_peer 2.2.3.1 port 500
     PERMIT, flags={origin_is_acl,}
    #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
    #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
    #pkts compressed: 0, #pkts decompressed: 0
    #pkts not compressed: 0, #pkts compr. failed: 0
    #pkts not decompressed: 0, #pkts decompress failed: 0
    #send errors 0, #recv errors 0

     local crypto endpt.: 2.2.1.1, remote crypto endpt.: 2.2.3.1
     plaintext mtu 1500, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet0/0
     current outbound spi: 0x0(0)
     PFS (Y/N): N, DH group: none

     inbound esp sas:

     inbound ah sas:

     inbound pcp sas:

     outbound esp sas:

     outbound ah sas:

     outbound pcp sas:
1 REPLY 1
Rob Ingram
VIP Mentor

Hi @TL64 

If you are pinging from the router itself (FW_LA_R) then the source of the pinging would be the outbound interface, which is not part of the crypto ACL that defines interesting traffic. Ping from an interface in the 10.10.x.x network.

 

If that doesn't work turn on debugs on both routers (debug crypto isakmp) and provide the output for review.

Content for Community-Ad