cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

231
Views
0
Helpful
5
Replies
Beginner

Bandwidth limiting on CT5760

Hi!

Please, help me to find info about per-client and per-SSID bandwidth rate limiting.

Or please, explain me shortly, how I can do only this, without enabling any QoS (as in 5508 for example)

WLC 5508 has options Per-User Bandwidth Contracts, Per-SSID Bandwidth Contracts on "WLAN NAME -> QoS" tab, but on CT5760 controller I can't find this. 

Software version 03.03.05SE

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Cisco Employee

QoS is enabled by default on

QoS is enabled by default on the 5760. Explicit marking of traffic is required in order to modify Class of Service (CoS) or Differentiated Services Code Point (DSCP) values for traffic from and to wired ports. Traffic from wireless to wireless ports or wireless to wired ports is considered untrusted. Though QoS is globally enabled if traffic passes through an SSID, it must be marked or trusted specifically, or all QoS values (DSCP, CoS) will be set to default (0).

Marking Models :

The WLC5760 supports several marking models:

    Per-Port Marking (wired)
    Per-Client Marking (wireless)
    Per-SSID Marking (wireless)
    Per-VLAN Marking (wired)

For more information, Please refer to the below link :

http://www.cisco.com/c/en/us/td/docs/wireless/technology/5760_deploy/CT5760_Controller_Deployment_Guide/QoS_Configuration.html

 

 

View solution in original post

5 REPLIES 5

Here you go with the below

Here you go with the below links you can find the about per-client and per-SSID bandwidth rate limiting.

www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/113682-bdr-limit-guide-00.html

 

Another discussion Related to the Bandwidth limit please go through .

https://supportforums.cisco.com/discussion/12105901/user-bandwidth-rate-limit

Beginner

Thank you for reply, but

Thank you for reply, but these articles don't give answers, because they are focused on AireOS.
Unfortunately, I can not find information about rate limiting in the IOS-based WLC

Enthusiast

check the following post,

check the following post, hope this will solve your issue.

 

https://supportforums.cisco.com/discussion/11278481/wlc-5508-and-anchorguestnet-rate-limit-traffic

 

https://supportforums.cisco.com/discussion/12218666/limit-traffic-qos-3750g

Highlighted
Cisco Employee

QoS is enabled by default on

QoS is enabled by default on the 5760. Explicit marking of traffic is required in order to modify Class of Service (CoS) or Differentiated Services Code Point (DSCP) values for traffic from and to wired ports. Traffic from wireless to wireless ports or wireless to wired ports is considered untrusted. Though QoS is globally enabled if traffic passes through an SSID, it must be marked or trusted specifically, or all QoS values (DSCP, CoS) will be set to default (0).

Marking Models :

The WLC5760 supports several marking models:

    Per-Port Marking (wired)
    Per-Client Marking (wireless)
    Per-SSID Marking (wireless)
    Per-VLAN Marking (wired)

For more information, Please refer to the below link :

http://www.cisco.com/c/en/us/td/docs/wireless/technology/5760_deploy/CT5760_Controller_Deployment_Guide/QoS_Configuration.html

 

 

View solution in original post

Beginner

Thank you very much.It is

Thank you very much.

It is already fixed with QoS. 

CreatePlease to create content
Content for Community-Ad

August's Community Spotlight Awards