cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
7164
Views
0
Helpful
13
Replies

Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?

aricardor
Level 1
Level 1

Hi!

I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...

I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).

------------------------------------------------------

Log from AP:

using ÿÿÿÿ ddr static values from serial eeprom

ddr init done

Running Normal Memtest...

Passed.

IOS Bootloader - Starting system.

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

................................................................................

................................................................................

................................................................................

......

Xmodem file system is available.

DDR values used from system serial eeprom.

WRDTR,CLKTR: 0x83000800, 0xc0000000

RQDC, RFDC : 0x80000037, 0x00000184

PCIE0: link is up.

PCIE0: VC0 is active

PCIE1: link is NOT up.

PCIE1 port 1 not initialize

PCIEx: initialization done

flashfs[0]: 6 files, 2 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 32385024

flashfs[0]: Bytes used: 2369024

flashfs[0]: Bytes available: 30016000

flashfs[0]: flashfs fsck took 21 seconds.

Reading cookie from system serial eeprom...Done

Base Ethernet MAC address: 44:2b:03:dc:09:25

Ethernet speed is 1000 Mb - FULL duplex

Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################

################################################################################

################################################################################

############################

File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr

y point: 0x4000

executing...

enet halted

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA

SE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Tue 01-Jun-10 12:53 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

................................................................................

................................................................................

................................................................................

......

flashfs[1]: 6 files, 2 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 32126976

flashfs[1]: Bytes used: 2369024

flashfs[1]: Bytes available: 29757952

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 1 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 1000 Mb - FULL duplex

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-LAP1041N-E-K9    (PowerPC405ex) processor (revision B0) with 98294K/32

768K bytes of memory.

Processor board ID FCZ1611W414

PowerPC405ex CPU at 333Mhz, revision number 0x147E

Last reset from reload

LWAPP image version 7.0.94.21

1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 44:2B:03:DC:09:25

Part Number                          : 73-14034-04

PCA Assembly Number                  : 800-34273-05

PCA Revision Number                  : A0

PCB Serial Number                    : FOC16075VZ3

Top Assembly Part Number             : 800-34284-03

Top Assembly Serial Number           : FCZ1611W414

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1041N-E-K9

% Please define a domain-name first.

Press RETURN to get started!

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)

*Mar  1 00:00:09.574: *** CRASH_LOG = YES

Base Ethernet MAC address: 44:2B:03:DC:09:25

*Mar  1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log

(contains, 1024 messages)

*Mar  1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state

to up

*Mar  1 00:00:11.892: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA

SE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Tue 01-Jun-10 12:53 by prod_rel_team

*Mar  1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth

ernet0, changed state to up

logging facility kern

        ^

% Invalid input detected at '^' marker.

*Mar  1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL

LER

*Mar  1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS

IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)

*Mar  1 00:09:08.282:  -Verify the required power-injector is installed on this

port: AIR-CT5508-K9(Gig 0/0/2).

*Mar  1 00:09:08.282:  -If a power-injector is installed, issue the command:"pow

er inline negotiation injector installed"

*Mar  1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using

static IP. Forcing AP to use DHCP.

*Mar  1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

not have an Ip !!

*Mar  1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

not have an Ip !!

*Mar  1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

not have an Ip !!

*Mar  1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

not have an Ip !!

*Mar  1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

not have an Ip !!

Not in Bound state.

*Mar  1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

not have an Ip !!

*Mar  1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP

. Renewing DHCP IP.

logs from wireless controller:

(Cisco Controller) >show interface summary

Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Gu

est

-------------------------------- ---- -------- --------------- ------- ------ --

---

ap-manager                       2    untagged 209.165.200.231 Dynamic Yes    No

management                       1    untagged 209.165.200.230 Static  Yes    No

service-port                     N/A  N/A      192.168.1.157   Static  No     No

virtual                          N/A  N/A      1.1.1.1         Static  No     No

(Cisco Controller) >

i conect with service-port ok  and the management port works, i think.

AP442b.03dc.0925>ping 209.165.200.230

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms

AP442b.03dc.0925>

Help, please!

i write in spanish:

Hola:

Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, Gracias

1 Accepted Solution

Accepted Solutions

Scott Fella
Hall of Fame
Hall of Fame

Please make sure your time is set correctly on the wlc. Also make sure you set the country domain on the wlc that matches your AP. I would then place the ap on the same subnet as your management up address of your 5508. Why did you create an ap manager on the 5508. You should set the management to be the dynamic ap manager so you only need one up address. If the ap and wlc is on the same subnet, the ap will join the wlc. Then you can move the ap to another subnet after it joins.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

View solution in original post

13 Replies 13

Scott Fella
Hall of Fame
Hall of Fame

Please make sure your time is set correctly on the wlc. Also make sure you set the country domain on the wlc that matches your AP. I would then place the ap on the same subnet as your management up address of your 5508. Why did you create an ap manager on the 5508. You should set the management to be the dynamic ap manager so you only need one up address. If the ap and wlc is on the same subnet, the ap will join the wlc. Then you can move the ap to another subnet after it joins.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

Hi;

thank you so much.

The time and the country domain is set correctly on the wlc, but not on AP, how do i do? .  I delete the ap-manager, but i have a lot of dudes. The service-port ip address and the managament ip address could be at different nets? How can the ap to access the internet?   thanks

Hola:

lo primero, gracias.

El tiempo y la zona de pais (ES) está correctas en el WLC, pero en el AP no, ¿cómo se hace? He borrado la interfaz ap-manager, pero tengo una serie de dudas: ¿La dirección IP del puerto de servicio y la dirección de la management pueden ser de distintas redes? ¿Cómo es capaz el punto de acceso de acceder a la internet? Gracias

All traffic tunnels back to the wlc if the APs are in local mode. When the ap joins, it will get the new time. The service port address should not be routable on the network and is suggested that you do not connect that to the network.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***

Make sure on the management interface you enable the checkbox for ap manger.

Thanks,

Scott Fella

Sent from my iPhone

-Scott
*** Please rate helpful posts ***

thank you very much. The checkbox for ap manager is enabled.

I  send a picture with the explanation with everything I do, I hope it is easier to understand.

Thanks

Antonio R.

Muchas gracias por tu ayuda. El cuadro de selección para la administración de AP en la interfaz management está habilitado. Te envío una imagen con una explicación de todo lo que hago, espero que sea más fácil de entender.

Recibe un cordial saludo

Antonio R.

You can't connect the ADSL to the service port.  The LAP1041 needs to connect to a switch and thw WLC port 1 needs to connect to a gigabit switch.  If you want to use the ADSL, then you need to connect that to either a switch and use port 2 or you can connect it directly to the ADSL router as long as it is gigabit.

-Scott
*** Please rate helpful posts ***

Can you post your show run-config from the cli of the WLC and also the switch?  Is this a managed switch?

-Scott
*** Please rate helpful posts ***

Hi!

Thanks you very much! Well, the switch is basic, d-link des-1005d, but it's fast ethernet.

I'll look to find a gigabit switch,then i'll comment  how it went.

A greeting

Antonio R.

Hola:

Muchas gracias. El switch es básico, un D-Link DES-1005D, pero es fasteth (10/100).

Buscaré un switch gigabit, y entoncés comentaré como ha ido.

Un saludo

Antonio R.

Can you please post the WLC command "sh sysinfo"?

Hi!

I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by  DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.

I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.

Before the logs, I see this message from AP:

*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller

version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC? 

Hola:

He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.

Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.

Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:

*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller

version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC? 

Un saludo

Antonio R.

(Cisco Controller) >show run-config

Press Enter to continue...

System Inventory

NAME: "Chassis"    , DESCR: "Cisco Wireless Controller"

PID: AIR-CT5508-K9,  VID: V02,  SN: FCW1608L05X

Burned-in MAC Address............................ C4:64:13:8F:93:40

Power Supply 1................................... Present, OK

Power Supply 2................................... Absent

Maximum number of APs supported.................. 25

Press Enter to continue or to abort

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 6.0.199.4

Bootloader Version............................... 1.0.1

Field Recovery Image Version..................... 6.0.182.0

Firmware Version................................. FPGA 1.3, Env 1.6, USB console

1.27

Build Type....................................... DATA + WPS

System Name...................................... CISCO-CAPWAP-CONTROLLER

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

IP Address....................................... 209.165.200.230

Last Reset....................................... Power on reset

System Up Time................................... 0 days 0 hrs 17 mins 45 secs

System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,

Rome, Vienna

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

Next Boot License Type........................... Permanent

Configured Country............................... ES  - Spain

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +36 C

External Temperature............................. +23 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 1

3rd Party Access Point Support................... Disabled

Number of Active Clients......................... 0

Burned-in MAC Address............................ C4:64:13:8F:93:40

Power Supply 1................................... Present, OK

Power Supply 2................................... Absent

Maximum number of APs supported.................. 25

Press Enter to continue or to abort

Switch Configuration

802.3x Flow Control Mode......................... Disable

FIPS prerequisite features....................... Disabled

secret obfuscation............................... Enabled

Network Information

RF-Network Name............................. hosp

Web Mode.................................... Disable

Secure Web Mode............................. Enable

Secure Web Mode Cipher-Option High.......... Disable

Secure Web Mode Cipher-Option SSLv2......... Enable

Secure Shell (ssh).......................... Enable

Telnet...................................... Disable

Ethernet Multicast Forwarding............... Disable

Ethernet Broadcast Forwarding............... Disable

AP Multicast/Broadcast Mode................. Unicast

IGMP snooping............................... Disabled

IGMP timeout................................ 60 seconds

User Idle Timeout........................... 300 seconds

ARP Idle Timeout............................ 300 seconds

Cisco AP Default Master..................... Enabled

AP Join Priority............................ Disable

Mgmt Via Wireless Interface................. Disable

Mgmt Via Dynamic Interface.................. Disable

Bridge MAC filter Config.................... Enable

Bridge Security Mode........................ EAP

Mesh Full Sector DFS........................ Enable

--More or (q)uit current module or to abort

--More or (q)uit current module or to abort

AP Fallback ................................ Enable

Web Auth Redirect Ports .................... 80

Fast SSID Change ........................... Disabled

IP/MAC Addr Binding Check .................. Enabled

Press Enter to continue or to abort

Port Summary

           STP   Admin   Physical   Physical   Link   Link

Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE    SFPType

-- ------- ---- ------- ---------- ---------- ------ ------- ------- ----------

1  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A     1000BaseTX

2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

3  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

4  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

5  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

6  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

7  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

8  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present

Press Enter to continue or to abort

AP Summary

Number of APs.................................... 0

Global AP User Name.............................. Not Configured

Global AP Dot1x User Name........................ Not Configured

AP Name             Slots  AP Model             Ethernet MAC       Location

     Port  Country  Priority

------------------  -----  -------------------  -----------------  -------------

---  ----  -------  ------

Press Enter to continue or to abort

Press Enter to continue or to abort

AP Location

Site Name........................................ default-group

Site Description.................................

WLAN ID          Interface          Network Admission Control

-------         -----------        --------------------------

1               management           Disabled

AP Name             Slots  AP Model             Ethernet MAC       Location

     Port  Country  Priority  GroupName

------------------  -----  -------------------  -----------------  -------------

---  ----  -------  --------  --------------------------

Press Enter to continue or to abort

AP Config

Press Enter to continue or to abort

Press Enter to continue or to abort

AP Airewave Director Configuration

Press Enter to continue or to abort

802.11a Configuration

802.11a Network.................................. Disabled

11nSupport....................................... Enabled

      802.11a Low Band........................... Enabled

      802.11a Mid Band........................... Enabled

      802.11a High Band.......................... Enabled

802.11a Operational Rates

    802.11a 6M Rate.............................. Mandatory

    802.11a 9M Rate.............................. Supported

    802.11a 12M Rate............................. Mandatory

    802.11a 18M Rate............................. Supported

    802.11a 24M Rate............................. Mandatory

    802.11a 36M Rate............................. Supported

    802.11a 48M Rate............................. Supported

    802.11a 54M Rate............................. Supported

802.11n MCS Settings:

    MCS 0........................................ Supported

    MCS 1........................................ Supported

    MCS 2........................................ Supported

    MCS 3........................................ Supported

    MCS 4........................................ Supported

    MCS 5........................................ Supported

    MCS 6........................................ Supported

--More or (q)uit current module or to abort

--More or (q)uit current module or to abort

    MCS 7........................................ Supported

    MCS 8........................................ Supported

    MCS 9........................................ Supported

    MCS 10....................................... Supported

    MCS 11....................................... Supported

    MCS 12....................................... Supported

    MCS 13....................................... Supported

    MCS 14....................................... Supported

    MCS 15....................................... Supported

802.11n Status:

    A-MPDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Disabled

        Priority 2............................... Disabled

        Priority 3............................... Disabled

        Priority 4............................... Disabled

        Priority 5............................... Disabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

Beacon Interval.................................. 100

CF Pollable mandatory............................ Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

--More or (q)uit current module or to abort

--More or (q)uit current module or to abort

CFP Maximum Duration............................. 60

Default Channel.................................. 36

Default Tx Power Level........................... 0

DTPC  Status..................................... Enabled

Fragmentation Threshold.......................... 2346

TI Threshold..................................... -50

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

Call Admision Control (CAC) configuration

Voice AC:

   Voice AC - Admission control (ACM)............ Disabled

   Voice max RF bandwidth........................ 75

   Voice reserved roaming bandwidth.............. 6

   Voice load-based CAC mode..................... Disabled

   Voice tspec inactivity timeout................ Disabled

   Voice Stream-Size............................. 84000

   Voice Max-Streams............................. 2

Video AC:

   Video AC - Admission control (ACM)............ Disabled

--More or (q)uit current module or to abort

--More or (q)uit current module or to abort

   Video max RF bandwidth........................ Infinite

   Video reserved roaming bandwidth.............. 0

Press Enter to continue or to abort

802.11a Advanced Configuration

Press Enter to continue or to abort

802.11a Airewave Director Configuration

RF Event and Performance Logging

  Channel Update Logging......................... Off

  Coverage Profile Logging....................... Off

  Foreign Profile Logging........................ Off

  Load Profile Logging........................... Off

  Noise Profile Logging.......................... Off

  Performance Profile Logging.................... Off

  TxPower Update Logging......................... Off

Default 802.11a AP performance profiles

  802.11a Global Interference threshold.......... 10 %

  802.11a Global noise threshold................. -70 dBm

  802.11a Global RF utilization threshold........ 80 %

  802.11a Global throughput threshold............ 1000000 bps

  802.11a Global clients threshold............... 12 clients

Default 802.11a AP monitoring

  802.11a Monitor Mode........................... enable

  802.11a Monitor Mode for Mesh AP Backhaul...... disable

  802.11a Monitor Channels....................... Country channels

  802.11a AP Coverage Interval................... 180 seconds

  802.11a AP Load Interval....................... 60 seconds

  802.11a AP Noise Interval...................... 180 seconds

--More or (q)uit current module or to abort

--More or (q)uit current module or to abort

  802.11a AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

  Transmit Power Assignment Mode................. AUTO

  Transmit Power Update Interval................. 600 seconds

  Transmit Power Threshold....................... -70 dBm

  Transmit Power Neighbor Count.................. 3 APs

  Min Transmit Power............................. -10 dBm

  Max Transmit Power............................. 30 dBm

  Transmit Power Update Contribution............. SNI.

  Transmit Power Assignment Leader............... c4:64:13:8f:93:40

  Last Run....................................... 75 seconds ago

Coverage Hole Detection

  802.11a Coverage Hole Detection Mode........... Enabled

  802.11a Coverage Voice Packet Count............ 100 packets

  802.11a Coverage Voice Packet Percentage....... 50%

  802.11a Coverage Voice RSSI Threshold.......... -80 dBm

  802.11a Coverage Data Packet Count............. 50 packets

  802.11a Coverage Data Packet Percentage........ 50%

  802.11a Coverage Data RSSI Threshold........... -80 dBm

  802.11a Global coverage exception level........ 25 %

  802.11a Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

  Channel Assignment Mode........................ AUTO

--More or (q)uit current module or to abort

  Channel Update Interval........................ 600 seconds [startup]

  Anchor time (Hour of the day).................. 0

  Channel Update Contribution.................... SNI.

  Channel Assignment Leader...................... c4:64:13:8f:93:40

  Last Run....................................... 75 seconds ago

  DCA Sensitivity Level.......................... STARTUP (5 dB)

  DCA 802.11n Channel Width...................... 20 MHz

  DCA Minimum Energy Limit....................... -95 dBm

  Channel Energy Levels

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  Channel Dwell Times

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  802.11a 5 GHz Auto-RF Channel List

    Allowed Channel List......................... 36,40,44,48,52,56,60,64

    Unused Channel List.......................... 100,104,108,112,116,120,124,

                                                  128,132,136,140

  DCA Outdoor AP option.......................... Disabled

Radio RF Grouping

  802.11a Group Mode............................. AUTO

--More or (q)uit current module or to abort

  802.11a Group Update Interval.................. 600 seconds

  802.11a Group Leader........................... c4:64:13:8f:93:40

    802.11a Group Member......................... c4:64:13:8f:93:40

  802.11a Last Run............................... 75 seconds ago

802.11b Configuration

802.11b Network.................................. Enabled

11gSupport....................................... Enabled

11nSupport....................................... Enabled

802.11b/g Operational Rates

    802.11b/g 1M Rate............................ Mandatory

    802.11b/g 2M Rate............................ Mandatory

    802.11b/g 5.5M Rate.......................... Mandatory

    802.11b/g 11M Rate........................... Mandatory

    802.11g 6M Rate.............................. Supported

    802.11g 9M Rate.............................. Supported

    802.11g 12M Rate............................. Supported

    802.11g 18M Rate............................. Supported

    802.11g 24M Rate............................. Supported

    802.11g 36M Rate............................. Supported

    802.11g 48M Rate............................. Supported

    802.11g 54M Rate............................. Supported

802.11n MCS Settings:

    MCS 0........................................ Supported

    MCS 1........................................ Supported

    MCS 2........................................ Supported

    MCS 3........................................ Supported

    MCS 4........................................ Supported

--More or (q)uit current module or to abort

    MCS 5........................................ Supported

    MCS 6........................................ Supported

    MCS 7........................................ Supported

    MCS 8........................................ Supported

    MCS 9........................................ Supported

    MCS 10....................................... Supported

    MCS 11....................................... Supported

    MCS 12....................................... Supported

    MCS 13....................................... Supported

    MCS 14....................................... Supported

    MCS 15....................................... Supported

802.11n Status:

    A-MPDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Disabled

        Priority 2............................... Disabled

        Priority 3............................... Disabled

        Priority 4............................... Disabled

        Priority 5............................... Disabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

Beacon Interval.................................. 100

CF Pollable mode................................. Disabled

--More or (q)uit current module or to abort

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 1

Default Tx Power Level........................... 0

DTPC  Status..................................... Enabled

Call Admission Limit  ........................... 105

G711 CU Quantum ................................. 15

ED Threshold..................................... -50

Fragmentation Threshold.......................... 2346

PBCC mandatory................................... Disabled

RTS Threshold.................................... 2347

Short Preamble mandatory......................... Enabled

Short Retry Limit................................ 7

Legacy Tx Beamforming setting.................... Enabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

Faster Carrier Tracking Loop..................... Disabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

Call Admision Control (CAC) configuration

   Voice AC - Admission control (ACM)............ Disabled

--More or (q)uit current module or to abort

   Voice Stream-Size............................. 84000

   Voice Max-Streams............................. 2

   Voice max RF bandwidth........................ 75

   Voice reserved roaming bandwidth.............. 6

   Voice load-based CAC mode..................... Disabled

   Voice tspec inactivity timeout................ Disabled

   Video AC - Admission control (ACM)............ Disabled

   Video max RF bandwidth........................ 50

   Video reserved roaming bandwidth.............. 0

802.11b Advanced Configuration

Press Enter to continue or to abort

802.11b Airewave Director Configuration

RF Event and Performance Logging

  Channel Update Logging......................... Off

  Coverage Profile Logging....................... Off

  Foreign Profile Logging........................ Off

  Load Profile Logging........................... Off

  Noise Profile Logging.......................... Off

  Performance Profile Logging.................... Off

  Transmit Power Update Logging.................. Off

Default 802.11b AP performance profiles

  802.11b Global Interference threshold.......... 10 %

  802.11b Global noise threshold................. -70 dBm

  802.11b Global RF utilization threshold........ 80 %

  802.11b Global throughput threshold............ 1000000 bps

  802.11b Global clients threshold............... 12 clients

Default 802.11b AP monitoring

  802.11b Monitor Mode........................... enable

  802.11b Monitor Channels....................... Country channels

  802.11b AP Coverage Interval................... 180 seconds

  802.11b AP Load Interval....................... 60 seconds

  802.11b AP Noise Interval...................... 180 seconds

  802.11b AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

  Transmit Power Assignment Mode................. AUTO

  Transmit Power Update Interval................. 600 seconds

  Transmit Power Threshold....................... -70 dBm

  Transmit Power Neighbor Count.................. 3 APs

  Min Transmit Power............................. -10 dBm

  Max Transmit Power............................. 30 dBm

  Transmit Power Update Contribution............. SNI.

  Transmit Power Assignment Leader............... c4:64:13:8f:93:40

  Last Run....................................... 213 seconds ago

Coverage Hole Detection

  802.11b Coverage Hole Detection Mode........... Enabled

  802.11b Coverage Voice Packet Count............ 100 packets

  802.11b Coverage Voice Packet Percentage....... 50%

  802.11b Coverage Voice RSSI Threshold.......... -80 dBm

  802.11b Coverage Data Packet Count............. 50 packets

  802.11b Coverage Data Packet Percentage........ 50%

  802.11b Coverage Data RSSI Threshold........... -80 dBm

  802.11b Global coverage exception level........ 25 %

  802.11b Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

  Channel Assignment Mode........................ AUTO

  Channel Update Interval........................ 600 seconds [startup]

  Anchor time (Hour of the day).................. 0

  Channel Update Contribution.................... SNI.

  Channel Assignment Leader...................... c4:64:13:8f:93:40

  Last Run....................................... 213 seconds ago

  DCA Sensitivity Level: ...................... STARTUP (5 dB)

  DCA Minimum Energy Limit....................... -95 dBm

  Channel Energy Levels

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  Channel Dwell Times

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  802.11b Auto-RF Allowed Channel List........... 1,6,11

  Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13

Radio RF Grouping

  802.11b Group Mode............................. AUTO

  802.11b Group Update Interval.................. 600 seconds

  802.11b Group Leader........................... c4:64:13:8f:93:40

    802.11b Group Member......................... c4:64:13:8f:93:40

  802.11b Last Run............................... 213 seconds ago

Mobility Configuration

Symmetric Mobility Tunneling (current) .......... Enabled

Symmetric Mobility Tunneling (after reboot) ..... Enabled

Mobility Protocol Port........................... 16666

Default Mobility Domain.......................... hosp

Multicast Mode .................................. Disabled

Mobility Domain ID for 802.11r................... 0x97e2

Mobility Keepalive Interval...................... 10

Mobility Keepalive Count......................... 3

Mobility Group Members Configured................ 1

Mobility Control Message DSCP Value.............. 0

Controllers configured in the Mobility Group

MAC Address        IP Address       Group Name                        Multicast

IP     Status

c4:64:13:8f:93:40  209.165.200.230  hosp                              0.0.0.0

        Up

Advanced Configuration

Probe request filtering..........................  Enabled

Probes fwd to controller per client per radio....  0

Probe request rate-limiting interval.............  500 msec

EAP-Identity-Request Timeout (seconds)........... 30

EAP-Identity-Request Max Retries................. 2

EAP Key-Index for Dynamic WEP.................... 0

EAP Max-Login Ignore Identity Response........... enable

EAP-Request Timeout (seconds).................... 30

EAP-Request Max Retries.......................... 2

EAPOL-Key Timeout (milliseconds)................. 1000

EAPOL-Key Max Retries............................ 2

dot11-padding.................................... Disabled

Authentication Response Timeout (seconds)........ 10

Rogue Entry Timeout (seconds).................... 1200

AP Heart Beat Timeout (seconds).................. 30

AP Discovery Timeout (seconds)................... 10

AP Local mode Fast Heartbeat (seconds)........... disable

AP Hreap mode Fast Heartbeat (seconds)........... disable

AP Primary Discovery Timeout (seconds)........... 120

AP Primed Join Timeout (seconds)................. 0

Packet Forwarding watchdog timer (seconds)....... 240 (enable)

Location Configuration

RFID Tag data Collection......................... Enabled

RFID  timeout.................................... 1200 seconds

RFID mobility.................................... Oui:00:14:7e : Vendor:pango  S

tate:Disabled

Interface Configuration

Interface Name................................... management

MAC Address...................................... c4:64:13:8f:93:40

IP Address....................................... 209.165.200.230

IP Netmask....................................... 255.255.255.0

IP Gateway....................................... 209.165.200.1

External NAT IP State............................ Disabled

External NAT IP Address.......................... 192.168.1.1

VLAN............................................. untagged

Quarantine-vlan.................................. 0

Active Physical Port............................. 1

Primary Physical Port............................ 1

Backup Physical Port............................. Unconfigured

Primary DHCP Server.............................. 209.165.200.230

Secondary DHCP Server............................ Unconfigured

DHCP Option 82................................... Disabled

ACL.............................................. Unconfigured

AP Manager....................................... Yes

Guest Interface.................................. No

Interface Name................................... service-port

MAC Address...................................... c4:64:13:8f:93:41

IP Address....................................... 192.168.1.157

IP Netmask....................................... 255.255.255.0

DHCP Option 82................................... Disabled

DHCP Protocol.................................... Disabled

AP Manager....................................... No

Guest Interface.................................. No

Interface Name................................... virtual

MAC Address...................................... c4:64:13:8f:93:40

IP Address....................................... 1.1.1.1

DHCP Option 82................................... Disabled

Virtual DNS Host Name............................ Disabled

AP Manager....................................... No

Guest Interface.................................. No

WLAN Configuration

WLAN Identifier.................................. 1

Profile Name..................................... HOSP3C

Network Name (SSID).............................. HOSP3C

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

  NAC-State...................................... Disabled

  Quarantine VLAN................................ 0

Number of Active Clients......................... 0

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

WLAN ACL......................................... unconfigured

DHCP Server...................................... 209.165.200.230

DHCP Address Assignment Required................. Enabled

Quality of Service............................... Platinum (voice)

Scan Defer Priority.............................. 5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Disabled

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... 802.11b and 802.11g only

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

   Authentication................................ Disabled

   Accounting.................................... Disabled

   Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

   802.11 Authentication:........................ Open System

   Static WEP Keys............................... Disabled

   802.1X........................................ Disabled

   Wi-Fi Protected Access (WPA/WPA2)............. Enabled

      WPA (SSN IE)............................... Disabled

      WPA2 (RSN IE).............................. Enabled

         TKIP Cipher............................. Enabled

         AES Cipher.............................. Enabled

      Auth Key Management

         802.1x.................................. Disabled

         PSK..................................... Enabled

         CCKM.................................... Disabled

         FT(802.11r)............................. Disabled

         FT-PSK(802.11r)......................... Disabled

FT Reassociation Timeout......................... 20

FT Over-The-Air mode............................. Enabled

FT Over-The-Ds mode.............................. Enabled

   CKIP ......................................... Disabled

   Web Based Authentication...................... Disabled

   Web-Passthrough............................... Disabled

   Conditional Web Redirect...................... Disabled

   Splash-Page Web Redirect...................... Disabled

   Auto Anchor................................... Disabled

   H-REAP Local Switching........................ Disabled

   H-REAP Learn IP Address....................... Enabled

   Infrastructure MFP protection................. Enabled

   Client MFP.................................... Optional

   Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Band Select...................................... Enabled

Load Balancing................................... Enabled

Mobility Anchor List

WLAN ID     IP Address            Status

-------     ---------------       ------

Press Enter to continue or to abort

Press Enter to continue or to abort

ACL Configuration

Press Enter to continue or to abort

CPU ACL Configuration

CPU Acl Name................................ NOT CONFIGURED

Wireless Traffic............................ Disabled

Wired Traffic............................... Disabled

RADIUS Configuration

Vendor Id Backward Compatibility................. Disabled

Call Station Id Case............................. lower

Call Station Id Type............................. IP Address

Aggressive Failover.............................. Enabled

Keywrap.......................................... Disabled

Fallback Test:

    Test Mode.................................... Off

    Probe User Name.............................. cisco-probe

    Interval (in seconds)........................ 300

MAC Delimiter for Authentication Messages........ hyphen

MAC Delimiter for Accounting Messages............ hyphen

Authentication Servers

Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/P

hase1/Group/Lifetime/Auth/Encr

---  ----  ----------------  ------  --------  ----  -------  ------------------

------------------------------

Accounting Servers

Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/P

hase1/Group/Lifetime/Auth/Encr

---  ----  ----------------  ------  --------  ----  -------  ------------------

------------------------------

--More or (q)uit current module or to abort

TACACS Configuration

Authentication Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Authorization Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Accounting Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

LDAP Configuration

Press Enter to continue or to abort

Local EAP Configuration

User credentials database search order:

    Primary ..................................... Local DB

Timer:

    Active timeout .............................. 300

Configured EAP profiles:

EAP Method configuration:

    EAP-FAST:

      Server key ................................

      TTL for the PAC ........................... 10

      Anonymous provision allowed ............... Yes

      Authority ID .............................. 436973636f00000000000000000000

00

      Authority Information ..................... Cisco A-ID

Press Enter to continue or to abort

HREAP Group Summary

HREAP Group Summary: Count: 0

Group Name                # Aps

Press Enter to continue or to abort

HREAP Group Detail

Press Enter to continue or to abort

Route  Info

Number of Routes................................. 0

Destination Network          Netmask               Gateway

-------------------    -------------------   -------------------

Press Enter to continue or to abort

Qos Queue Length Info

Platinum queue length............................ 100

Gold queue length................................  75

Silver queue length..............................  50

Bronze queue length..............................  25

Press Enter to continue or to abort

Mac Filter Info

Press Enter to continue or to abort

Authorization List

Authorize MIC APs against AAA ................... disabled

Authorize LSC APs against Auth-List ............. disabled

Allow APs with MIC - Manufactured Installed C.... disabled

Allow APs with SSC - Self-Signed Certificate..... disabled

Allow APs with LSC - Locally Significant Cert.... disabled

Load Balancing Info

Aggressive Load Balancing........................ Disabled

Aggressive Load Balancing Window................. 5 clients

Aggressive Load Balancing Denial Count........... 3

Statistics

Total Denied Count............................... 0 clients

Total Denial Sent................................ 0 messages

Exceeded Denial Max Limit Count.................. 0 times

None 5G Candidate Count.......................... 0 times

None 2.4G Candidate Count........................ 0 times

Press Enter to continue or to abort

Dhcp Scope Info

Scope: PUNTOSAP

Enabled.......................................... Yes

Lease Time....................................... 86400 (1 day )

Pool Start....................................... 209.165.200.201

Pool End......................................... 209.165.200.229

Network.......................................... 209.165.200.0

Netmask.......................................... 255.255.255.0

Default Routers.................................. 0.0.0.0  0.0.0.0  0.0.0.0

DNS Domain.......................................

DNS.............................................. 0.0.0.0  0.0.0.0  0.0.0.0

Netbios Name Servers............................. 0.0.0.0  0.0.0.0  0.0.0.0

Press Enter to continue or to abort

Exclusion List ConfigurationUnable to retrieve exclusion-list entry

Press Enter to continue or to abort

CDP Configuration

Press Enter to continue or to abort

Country Channels Configuration

Configured Country............................. ES  - Spain

      KEY: * = Channel is legal in this country and may be configured manually.

           A = Channel is the Auto-RF default in this country.

           . = Channel is not legal in this country.

           C = Channel has been configured for use by Auto-RF.

           x = Channel is available to be configured for use by Auto-RF.

         (-,-) = (indoor, outdoor) regulatory doamin allowed by this country.

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

    802.11bg     :

    Channels     :                   1 1 1 1 1

                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

ES (-E   ,-E   ): A * * * * A * * * * A * * .

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

    802.11a      :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

    Channels     : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6

                 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

ES (-E   ,-E   ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .

Press Enter to continue or to abort

WPS Configuration Summary

Auto-Immune

  Auto-Immune.................................... Disabled

Client Exclusion Policy

  Excessive 802.11-association failures.......... Enabled

  Excessive 802.11-authentication failures....... Enabled

  Excessive 802.1x-authentication................ Enabled

  IP-theft....................................... Enabled

  Excessive Web authentication failure........... Enabled

Signature Policy

  Signature Processing........................... Enabled

Press Enter to continue or to abort

Custom Web Configuration

Radius Authentication Method..................... PAP

Cisco Logo....................................... Enabled

CustomLogo....................................... None

Custom Title..................................... None

Custom Message................................... None

Custom Redirect URL.............................. None

Web Authentication Type.......................... Internal Default

External Web Authentication URL.................. None

Configuration Per Profile:

Rogue AP Configuration

Rogue Location Discovery Protocol................ Disabled

Rogue on wire Auto-Contain....................... Disabled

Rogue using our SSID Auto-Contain................ Disabled

Valid client on rogue AP Auto-Contain............ Disabled

Rogue AP timeout................................. 1200

MAC Address        Classification     # APs # Clients Last Heard

-----------------  ------------------ ----- --------- -----------------------

Adhoc Rogue Configuration

Detect and report Ad-Hoc Networks................ Enabled

Auto-Contain Ad-Hoc Networks..................... Disabled

Client MAC Address  Adhoc BSSID         State              # APs   Last Heard

------------------  ------------------  -----------------  ------  -------------

----------

Rogue Client Configuration

Validate rogue clients against AAA............... Disabled

Rogue Client Configuration

Validate rogue clients against AAA............... Disabled

--More-- or (q)uit

MAC Address        State              # APs Last Heard

-----------------  ------------------ ----- -----------------------

Ignore List Configuration

MAC Address

-----------------

Rogue Rule Configuration

Priority Rule Name               State    Type          Match Hit Count

-------- ----------------------- -------- ------------- ----- ---------

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 6.0.199.4

Bootloader Version............................... 1.0.1

Field Recovery Image Version..................... 6.0.182.0

Firmware Version................................. FPGA 1.3, Env 1.6, USB console

1.27

Build Type....................................... DATA + WPS

System Name...................................... CISCO-CAPWAP-CONTROLLER

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

IP Address....................................... 209.165.200.230

Last Reset....................................... Power on reset

System Up Time................................... 0 days 0 hrs 41 mins 2 secs

System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,

Rome, Vienna

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

Next Boot License Type........................... Permanent

Configured Country............................... ES  - Spain

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +39 C

External Temperature............................. +23 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Disabled

Number of WLANs.................................. 1

3rd Party Access Point Support................... Disabled

Number of Active Clients......................... 0

Burned-in MAC Address............................ C4:64:13:8F:93:40

Power Supply 1................................... Present, OK

Power Supply 2................................... Absent

Maximum number of APs supported.................. 25

(Cisco Controller) >

The AP log

AP442b.03dc.0925>

*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER

'(index 0).

*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller

logging facility kern

        ^

% Invalid input detected at '^' marker.

logging facility kern

        ^

% Invalid input detected at '^' marker.

*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i

p: 209.165.200.230 peer_port: 5246

*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully

peer_ip: 209.165.200.230 peer_port: 5246

*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23

0

*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller

version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?

*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209

.165.200.230:5246

*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is

not established

You just found the solution to your problem.  You need to use WLC firmware 7.0.98.0 (and later) so the WLC can support the 1040 WAP.

Thank you! I try to download the firmware. But i need "BID" (?), and i don't know the steps to uptade the wlc.

¡Gracias!, después de tres días me doy cuenta de eso. Intentaré descargarme el firmware, pero necesito un acceso especial, el ¿BID?, aparte de que no sé como actualizar el WLC.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: