Re: how i can AP is AIR-AP1815I-I-K 9 ???,

Dhikra Marghli · ‎02-11-2019

N(Cisco Controller) >show ap summary

Number of APs.................................... 2

Global AP User Name.............................. AP-TEST
Global AP Dot1x User Name........................ Not Configured
Global AP Dot1x EAP Method....................... EAP-FAST

* prefix indicates Cisco Internal AP

AP Name Slots AP Model Ethernet MAC Location Country IP Address Clients DSE
------------------------------ ----- -------------------- ----------------- -------------------- ---------- --------------- ------- ----
*AP780C.F0DB.2A90 2 AIR-AP1815I-I-K9 78:0c:f0:db:2a:90 default location TN 1.1.1.134 0 [0
AP28AC.9E89.48E0 2 AIR-AP1815I-I-K 28:ac:9e:89:48:e0 default location 1.1.1.25 0 [0

when i configured the AP28AC.9E89.48E0 with the same configuration code country TN as AP780C.F0DB.2A90 ,

teh AP don't accpted the code country and tell me AP name invalid :

config ap disable .......

config ap country TN ......

Other RQ: how i can allow AP28AC.9E89.48E0 is AIR-AP1815I-I-K 9 ?????????,

1) Why AP1 with AIR-AP1815I-I-K 9 and AP 2 AIR-AP1815I-I-K ?????, :

2) WHY AP2 don't accpet any country ?,, what i can do with AP2

3) AP1 version 8.8.100 and AP2 8.8.100

thanks in advance

Dhikra Marghli · ‎02-11-2019

Why AP have AIR-AP1815I-I-K not AIR-AP1815I-I-K9 ??????,

what is solution thta allow AP to be as AP 1?

AP 1 8..8.100 and backup 8.8.111

then what IOS that allow problem AP to be as AIR-AP1815I-I-K9!!

Flavio Miranda · ‎02-11-2019

Hi

1) Why AP1 with AIR-AP1815I-I-K 9 and AP 2 AIR-AP1815I-I-K ?????, :

We can see two types:

AIR-AP1815i-x-K9 - controller-based

AIR-AP1815i-x-K9C: Mobility Express

I´ve never see without the K9. What do you see if you look through the Web interface instead?

2) WHY AP2 don't accpet any country ?,, what i can do with AP2

The ‘ x ’ can be any one of these supported regulatory domains: A, B, C, D, E, F, H, I, K, N, Q, R, S, T, Z.

Which means, Tunisia is on the list. My suspicion is that this AP may have some problem and may need to be replaced.

-If I helped you somehow, please, rate it as useful.-

Dhikra Marghli · ‎02-11-2019

I give you a print screen about the two acces point : AP 1: moblity express and AP2 : acces point

2) when i try with new AP or any AP to be the same code country as ME ( AP1 °) and give the command :

config 802.11a disable network

onfig 802.11b disable network

config country

config 802.11a enable network
config 802.11b enable network

config ap disable  ......( name AP tell me is invalid name ) but i put the same name AP !!!?,,,,,

config ap country TN

show ap summary   :  alaway AP1( ME 1815I) is good and AP 2 do not accept the command  !!???,

So what do you think about other AP to be the same code country !!! and accpet the command

config ap disable ....( name AP)

ME : vesrion 8.8.100 and other AP 8..3.111 and 8.8.100 !!

Dhikra Marghli · ‎02-11-2019

Please , i wait a solution for this problem

config ap {{ enable | disable} cisco_ap ( Tell me Name of the Cisco lightweight access point. in nvalid ) !!!?,AP28AC.9E89.48E0 in invalid !!!!!

thanks

Dhikra Marghli · ‎02-11-2019

Plese you can read my messages properly about outbout of this command and configuration and say me what solution that i can to take ??

Thanks

Dhikra Marghli · ‎02-11-2019

If you have a solution then thanks to help me else , do not spend the time to answer me anything and heading to other discus!!!

please so can you help me !!!Thanks

Leo Laohoo · ‎02-11-2019

Please refer to CSCuw56127 and change the controller country settings to either Egypt or Israel.

Dhikra Marghli · ‎02-11-2019

(Cisco Controller) >show ap summary

Number of APs.................................... 2

Global AP User Name.............................. AP-TEST
Global AP Dot1x User Name........................ Not Configured
Global AP Dot1x EAP Method....................... EAP-FAST

* prefix indicates Cisco Internal AP

AP Name Slots AP Model Ethernet MAC Location Country IP Address Cl ients DSE Location
------------------------------ ----- -------------------- ----------------- -------------------- ---------- --------------- -- ----- --------------
*AP780C.F0DB.2A90 2 AIR-AP1815I-I-K9 78:0c:f0:db:2a:90 default location IL 1.1.1.134 1 [0 ,0 ,0 ]
AP2 2 AIR-AP1815I-I-K 28:ac:9e:89:3d:b8 default location 1.1.1.168 0 [0 ,0 ,0 ]

(Cisco Controller) >config ap disable AP2

Invalid parameter specified.

(Cisco Controller) >config ap country IL ?

<Cisco AP> Enter the name of the Cisco AP.
all Configure all the Cisco APs.

(Cisco Controller) >config ap country IL all

To change country code: first disable target AP(s) (or disable all networks).
Changing the country may reset any customized channel assignments.
Changing the country may reboot disabled target AP(s).

Are you sure you want to continue? (y/n) y

!!Warning!! Cannot change Country code on Universal APs.
AP Name Country Status
------------------ ------ -------
AP780C.F0DB.2A90 IL enabled (Disable AP before configuring country)

(Cisco Controller) >config ap disable ?

<Cisco AP> Enter the name of the Cisco AP.

(Cisco Controller) >config ap disable ?

<Cisco AP> Enter the name of the Cisco AP.

(Cisco Controller) >config ap disable AP2

Invalid parameter specified.

(Cisco Controller) >

what is a solution can AP accpet country !!????,,

Leo Laohoo · ‎02-12-2019

@Dhikra Marghli wrote:

what is a solution can AP accpet country !!????,,

Please read THIS.

Dhikra Marghli · ‎02-12-2019

i put ISARIL but ALSO AP 2 1815 don't accpeted any code country becuse the command

(Cisco Controller) >config ap disable

Incorrect input! Use 'config ap [enable/disable] <Cisco AP>'

(Cisco Controller) >config ap disable AP28AC.9E89.3E10

Cisco AP name is invalid.

/////////////////////////////////////////////////

Global AP User Name.............................. AP-TEST
Global AP Dot1x User Name........................ Not Configured
Global AP Dot1x EAP Method....................... EAP-FAST

* prefix indicates Cisco Internal AP

AP Name Slots AP Model Ethernet MAC Location Country IP Addr ess Clients DSE Location
------------------------------ ----- -------------------- ----------------- -------------------- ---------- ------- -------- ------- --------------
*AP780C.F0DB.2A90 2 AIR-AP1815I-I-K9 78:0c:f0:db:2a:90 default location IL 1.1.1 .134 0 [0 ,0 ,0 ]
AP28AC.9E89.3E10 2 AIR-AP1815I-I-K 28:ac:9e:89:3e:10 default location 1.1.1. 47 0 [0 ,0 ,0 ]

i put the same name of acces point but tell me invalid !!!

So please help me that allow ALL AP joind to ME 1815 !

Leo Laohoo · ‎02-12-2019

Config is disabled because the command is only valid when entered into a controller.
If the child AP is CAPWAP and has the Regulatory Domain of "-I" then wait for the ME to boot up with Israel or Egypt.

Dhikra Marghli · ‎02-12-2019

cisco AIR-AP1815I-I-K9 ARMv7 Processor rev 5 (v7l) with 1016100/788364K bytes of memory.
Processor board ID FGL2209B3S9
AP Running Image : 8.8.100.0
Primary Boot Image : 8.8.100.0
Backup Boot Image : 8.8.111.0
Primary Boot Image Hash: 5d18bf2dd83eb927f5db60ef46005440dd0a1c410284f278775b5e34a17cb0156d02e7976865236e7cb8ac69c2729979c1aa78d0cb2832298ce41c691ed9ce62
Backup Boot Image Hash: b74c97255daf86219bbab6c75d82d9de9b0f5bc4604b407288c5702261bd86597c9417cb6f67ebe5ba092274a814d5ef80504da416d1764168c7f162e9067a0d
1 Gigabit Ethernet interfaces
2 802.11 Radios
Radio FW version : ce271f0c3bd6087f274af2d1d72e15b7
NSS FW version : not available

Base ethernet MAC Address : 28:AC:9E:89:3D:B8
Part Number : 0-0000-00
PCA Assembly Number : 074-105850-02
PCA Revision Number : 0
PCB Serial Number : FOC22063AD0
Top Assembly Part Number : 074-105850-02
Top Assembly Serial Number : FGL2209B3S9
Top Revision Number : A0
Product/Model Number : AIR-AP1815I-I-K9
/////////////////////////////////////////////////////////////////////

AP2#show capwap client config
AdminState : ADMIN_ENABLED(1)
Name : AP2
Location : default location
Primary controller name : AP-TEST
Primary controller IP : 1.1.1.73
Secondary controller name :
Secondary controller IP :
Tertiary controller name :
Tertiary controller IP :
ssh status : Disabled
ApMode : Local
ApSubMode : None
Link-Encryption : Disabled
OfficeExtend AP : Disabled
Discovery Timer : 10
Heartbeat Timer : 30
Syslog server : 255.255.255.255
Syslog level : errors
AP join priority : 1
IP Prefer-mode : Unconfigured
CAPWAP UDP-Lite : Unconfigured
AP retransmit count : 5
AP retransmit timer : 3
AP lsc enable : 0
AP Policy Tag : UNKNOWN
AP RF Tag : UNKNOWN
AP Site Tag : UNKNOWN
AP Tag Source : 0
AP lsc reboot cnt : 0
AP lsc max num of retry : 0
SwVer : 8.8.100.0
spamStatTimer : 30
Led State Enabled : 1
Primed Interval : 0
AP ILP Pre-Standard Switch Support : Disabled
IPv4 TCP MSS Adjust : Disabled
IPv6 TCP MSS Adjust : Disabled
LinkFailure : 0
SpamReboots : 101
ApCrashes : 0
AP VLAN Tag status : Disabled 0
AP Power Injector : Disabled
Slot 0 Config:
Radio Type : RADIO_TYPE_80211bg
Radio Mode : Local
Country code :
Country ISO Code :
CleanAir Enable State : Disabled
Channel : 1
Automatic Config : 1
Channel Width : 20
Current Transmit Power : 1
Automatic Config : 1
DiversitySelection : Diversity Enabled
HT Rx Antenna Selection : 3
HT Tx Antenna Selection : 3
Antenna Band Mode : Antenna Sector B
Antenna Selection : Internal Antenna
Antenna Selection : Internal Antenna
Antenna Selection : Internal Antenna
Antenna Selection : Internal Antenna
Load Profile
RF Busy Threshold : 10
Clients Threshold : 12
Bytes/Second Threshold : 1000000
--More-- [*02/12/2019 10:26:27.4099] Image d
///////////////////////////////////////////////////////////////////////////////////////////////////////////

FOR Moblity express i changed Egypt.
Cisco Controller) >show ap summary

Number of APs.................................... 2

Global AP User Name.............................. AP-TEST
Global AP Dot1x User Name........................ Not Configured
Global AP Dot1x EAP Method....................... EAP-FAST

* prefix indicates Cisco Internal AP

AP Name Slots AP Model Ethernet MAC Location Country IP Address Clients DSE Location
------------------------------ ----- -------------------- ----------------- -------------------- ---------- --------------- ------- --------------
*AP780C.F0DB.2A90 2 AIR-AP1815I-I-K9 78:0c:f0:db:2a:90 default location EG 1.1.1.134 0 [0 ,0 ,0 ]
AP2 2 AIR-AP1815I-I-K 28:ac:9e:89:3d:b8 default location 1.1.1.168 0 [0 ,0 ,0 ]

//////////////////////////////////////////////////////////////

I wait several hours but others acces point don't recieve the country code and also in interface web same output as CLI .

1) i put this command in controller for other acces point to be same code country as ME !!!

So why i still in boucle problem . Please , i would the team of this group give me solution about others acces point code country !

thanks

Leo Laohoo · ‎02-12-2019

Can you try and force the AP to boot 8.8.111.0?

Dhikra Marghli · ‎02-12-2019

I put

config boot path 1

reload :===> same primary version

and also i try

config boot path 2

reload :===> same primary version

so please what command that force the AP to boot with 8.8.111 !!

thanks in advance