cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5216
Views
0
Helpful
8
Replies
Highlighted

Radio problem on an AP1142N

Hello,

I 've got a problem on an AP1142N. It joins correctly its controller (5508 WLC) but one of his radio (Dot11Radio1) won't go up :

#show cdp interface

Dot11Radio1 is reset, line protocol is down

  Encapsulation ARPA

  Sending CDP packets every 60 seconds

  Holdtime is 180 seconds

Here's what I have in my log file :

*Oct 19 11:13:20.536: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 11:13:21.036: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

Is it an hardware problem?

Regards,

Eric

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Community Legend

*Mar  1 00:00:09.233: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AES encrypt for TX on interface Dot11Radio 1 -Process= "Init", ipl= 0, pid= 3

RMA the WAP.  The radio module is faulty.

View solution in original post

8 REPLIES 8
Highlighted
Cisco Employee

Do you see anything in the log that mentions crash or traceback?

You may need to look at the previous log messages by typing this:

more flash:events.log

Can you also post the output for:

show ver

Highlighted
Hall of Fame Community Legend

Can you please post the complete output to the following commands:

1.  WLC:  sh sysinfo;

2.  WAP:  sh version; and

3.  WAP:  sh inventory

Highlighted

Hello,

I don't see anything special in the event.log file. This WAP is a new one (first time that it's connected on my network).

1.  WLC:  sh sysinfo;

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.98.214

Bootloader Version............................... 1.0.1

Field Recovery Image Version..................... N/A

Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27

Build Type....................................... DATA + WPS

System Name...................................... AIR-ILM-WLC-C5-01

System Location.................................. Etage-5_Bt-C

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1069

IP Address....................................... 10.226.232.130

Last Reset....................................... Software reset

System Up Time................................... 245 days 12 hrs 30 mins 23 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

Next Boot License Type........................... Permanent

Configured Country............................... FR  - France

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +44 C

External Temperature............................. +23 C

Fan Status....................................... OK

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 6

Number of Active Clients......................... 305

Burned-in MAC Address............................ 54:75:D0:DE:D0:C0

Power Supply 1................................... Present, OK

Power Supply 2................................... Present, OK

Maximum number of APs supported.................. 100

2.  WAP:  sh version

Cisco IOS Software, C1140 Software (C1140-K9W8-M), Experimental Version 12.4(20110214:185845) [BLD-wnbu_j_esc1.201102141046 161]

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Mon 14-Feb-11 11:39 by

ROM: Bootstrap program is C1140 boot loader

BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA, RELEASE SOFTWARE (fc3)

AIR-ILM-AP-A7-04 uptime is 4 days, 4 hours, 1 minute

System returned to ROM by watchdog timer expired

System image file is "flash:/c1140-k9w8-mx.wnbu_j_esc1.201102141046/c1140-k9w8-mx.wnb"

cisco AIR-LAP1142N-E-K9    (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.

Processor board ID FCZ1316W04X

PowerPC405ex CPU at 586Mhz, revision number 0x147E

Last reset from watchdog timer expired

LWAPP image version 7.0.98.214

1 Gigabit Ethernet interface

2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:22:90:91:2B:58

Part Number                          : 73-11451-05

PCA Assembly Number                  : 800-30554-02

PCA Revision Number                  : A0

PCB Serial Number                    : FOC13111JG2

Top Assembly Part Number             : 800-31273-01

Top Assembly Serial Number           : FCZ1316W04X

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1142N-E-K9  

Configuration register is 0xF

3.  WAP:  sh inventory

NAME: "AP1140", DESCR: "Cisco Aironet 1140 Series (IEEE 802.11n) Access Point"

PID: AIR-LAP1142N-E-K9 , VID: V01, SN: FCZ1316W04X

Regards,

Highlighted
Hall of Fame Community Legend

upgrade the firmware of the controller to the newer 7.3.X.

Highlighted
Cisco Employee

how the ap is powered.

what happens if tried to toggle ap and radio admin status from gui.

console into ap, bounce the ap, check the boot process for d1 radio initialization.

display - show cont d1, show log, more event.log.

Highlighted

It's powered by the switch (PoE).

show log :

Log Buffer (1048576 bytes):

*Mar  1 00:00:07.294: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar  1 00:00:07.305: *** CRASH_LOG = YES

Security Core found.

Base Ethernet MAC address: 00:22:90:91:2B:58

*Mar  1 00:00:08.669: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0

*Mar  1 00:00:09.233: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AES encrypt for TX on interface Dot11Radio 1 -Proce

ss= "Init", ipl= 0, pid= 3

*Mar  1 00:00:09.233: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AEC CCM encrypt on interface Dot11Radio 1 -Process= "Init", ipl= 0, pid= 3

*Mar  1 00:00:09.234: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AEC CCM decrypt on interface Dot11Radio 1 -Process= "Init", ipl= 0, pid= 3

*Mar  1 00:00:09.271: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 134 messages)

*Mar  1 00:00:09.291:  status of voice_diag_test from WLC is false

*Mar  1 00:00:10.331: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:11.409: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:11.452: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1140 Software (C1140-K9W8-M), Experimental Version 12.4(201

10214:185845) [BLD-wnbu_j_esc1.201102141046 161]

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Mon 14-Feb-11 11:39 by

*Mar  1 00:00:11.452: %SNMP-5-COLDSTART: SNMP agent on host AIR-ILM-AP-A7-04 is undergoing a cold start

*Mar  1 00:00:11.524: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Mar  1 00:00:11.524: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar  1 00:00:12.524: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

*Mar  1 00:00:12.524: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar  1 00:00:21.521: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar  1 00:00:21.522: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:00:22.074: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio0, Timed out waiting for fw to clear txp_pndg flag

*Mar  1 00:00:22.574: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Mar  1 00:00:22.775: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:00:30.357:  status of voice_diag_test from WLC is false

*Mar  1 00:00:30.395: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:00:34.965: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

*Mar  1 00:00:34.987: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Mar  1 00:00:35.972: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Mar  1 00:00:35.973: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated

*Mar  1 00:00:49.426: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

more flash:event.log

*Mar 1 00:00:30.133: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C4506-E (e05f.b91a.9dd1)

*Mar 1 00:00:38.324: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:00:38.326: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar 1 00:00:38.327: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER

*Oct 19 08:21:57.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller

*Oct 19 08:21:57.001: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 08:21:58.000: %CAPWAP-5-CHANGED: CAPWAP changed state to 

*Oct 19 08:21:58.829: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 08:21:58.829: %CAPWAP-5-SENDJOIN: sending Join Request to 10.226.232.130

*Oct 19 08:21:58.829: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Oct 19 08:21:58.837: %CAPWAP-5-CHANGED: CAPWAP changed state to IMAGE

*Oct 19 08:22:38.812: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C4506-E (e05f.b91a.9dd1)

*Oct 19 08:22:39.976: *** Access point reloading. Reason: NEW IMAGE DOWNLOAD ***

*Mar 1 00:00:32.363: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

*Mar 1 00:00:32.373: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Mar 1 00:00:33.359: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Mar 1 00:00:41.434: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:00:41.436: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Oct 19 08:24:19.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller

*Oct 19 08:24:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 08:24:20.000: %CAPWAP-5-CHANGED: CAPWAP changed state to 

*Oct 19 08:24:20.832: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 08:24:20.832: %CAPWAP-5-SENDJOIN: sending Join Request to 10.226.232.130

*Oct 19 08:24:20.832: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Oct 19 08:24:20.930: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Oct 19 08:24:21.047: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:24:21.054: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:24:21.539: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 08:24:22.203: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 08:24:22.212: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Oct 19 08:24:22.222: %LWAPP-3-CLIENTEVENTLOG: Received AP Syslog IP Address(255.255.255.255) configuration.

*Oct 19 08:24:22.222: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller AIR-ILM-WLC-C5-01

*Oct 19 08:24:22.224: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Oct 19 08:24:22.224: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:24:22.224: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[0]

*Oct 19 08:24:22.224: %LWAPP-3-CLIENTEVENTLOG: SSID Guest-ILM added to the slot[0]

*Oct 19 08:24:22.224: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[0]

*Oct 19 08:24:22.224: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[1]

*Oct 19 08:24:22.224: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OfficePhone added to the slot[1]

*Oct 19 08:24:22.224: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[1]

*Oct 19 08:24:22.232: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 4 due to WMM is not enabled

*Oct 19 08:24:22.232: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:24:23.231: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Oct 19 08:34:37.372: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:34:37.479: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:37:45.159: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.226.232.130:5246

*Oct 19 08:37:53.742: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Oct 19 08:37:53.746: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.

*Oct 19 08:37:53.749: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Oct 19 08:37:53.757: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Oct 19 08:37:53.761: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down

*Oct 19 08:37:53.764: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down

*Oct 19 08:37:53.764: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:37:53.771: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:37:54.271: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 08:37:54.279: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Oct 19 08:37:54.286: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Oct 19 08:37:54.286: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:37:54.286: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Oct 19 08:37:54.294: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:37:54.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'AIR-ILM-WLC-C5-01'(index 0).

*Oct 19 08:37:54.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller

*Oct 19 08:37:54.001: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 08:37:54.001: %CAPWAP-5-CHANGED: CAPWAP changed state to 

*Oct 19 08:37:54.835: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 08:37:54.835: %CAPWAP-5-SENDJOIN: sending Join Request to 10.226.232.130

*Oct 19 08:37:54.835: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Oct 19 08:37:54.944: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Oct 19 08:37:54.945: %LWAPP-3-CLIENTERRORLOG: spamSendDeleteMobile : AP is not UP state.

*Oct 19 08:37:54.946: %LWAPP-3-CLIENTERRORLOG: spamSendDeleteMobile : AP is not UP state.

*Oct 19 08:37:55.066: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:37:55.074: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:37:55.554: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 08:37:56.130: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 08:37:56.139: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Oct 19 08:37:56.144: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller AIR-ILM-WLC-C5-01

*Oct 19 08:37:56.157: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:37:56.157: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Oct 19 08:37:56.157: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[0]

*Oct 19 08:37:56.157: %LWAPP-3-CLIENTEVENTLOG: SSID Guest-ILM added to the slot[0]

*Oct 19 08:37:56.157: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[0]

*Oct 19 08:37:56.158: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[1]

*Oct 19 08:37:56.158: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OfficePhone added to the slot[1]

*Oct 19 08:37:56.158: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:37:56.159: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[1]

*Oct 19 08:37:57.155: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Oct 19 08:38:02.879: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 08:43:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN

*Oct 19 08:43:31.824: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down

*Oct 19 08:43:31.858: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down

*Oct 19 08:43:31.859: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[0]

*Oct 19 08:43:31.862: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[1]

*Oct 19 08:43:31.862: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OfficePhone added to the slot[1]

*Oct 19 08:43:31.864: %LWAPP-3-CLIENTEVENTLOG: SSID Guest-ILM added to the slot[0]

*Oct 19 08:43:31.866: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 3 due to WMM is not enabled

*Oct 19 08:43:31.912: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[0]

*Oct 19 08:43:31.916: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[1]

*Oct 19 08:43:31.919: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Oct 19 08:43:31.920: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 08:43:31.920: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Oct 19 08:43:31.928: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 08:43:42.034: *** Access point reloading. Reason: Recvd RESET req from Controller ***

*Mar 1 00:00:34.669: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

*Mar 1 00:00:34.679: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Mar 1 00:00:35.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Mar 1 00:00:49.426: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Oct 19 11:13:19.001: %CAPWAP-3-ERRORLOG: Selected MWAR 'AIR-ILM-WLC-C5-01'(index 0).

*Oct 19 11:13:19.001: %CAPWAP-3-ERRORLOG: Go join a capwap controller

*Oct 19 11:13:19.001: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 11:13:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to 

*Oct 19 11:13:19.836: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.226.232.130 peer_port: 5246

*Oct 19 11:13:19.836: %CAPWAP-5-SENDJOIN: sending Join Request to 10.226.232.130

*Oct 19 11:13:19.836: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Oct 19 11:13:19.922: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Oct 19 11:13:20.045: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 11:13:20.052: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 11:13:20.537: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 11:13:21.119: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag

*Oct 19 11:13:21.128: %CAPWAP-5-CHANGED: CAPWAP changed state to UP

*Oct 19 11:13:21.139: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller AIR-ILM-WLC-C5-01

*Oct 19 11:13:21.140: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Oct 19 11:13:21.141: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Oct 19 11:13:21.141: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[0]

*Oct 19 11:13:21.141: %LWAPP-3-CLIENTEVENTLOG: SSID Guest-ILM added to the slot[0]

*Oct 19 11:13:21.141: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[0]

*Oct 19 11:13:21.141: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OFFICE added to the slot[1]

*Oct 19 11:13:21.141: %LWAPP-3-CLIENTEVENTLOG: SSID XS4OfficePhone added to the slot[1]

*Oct 19 11:13:21.142: %LWAPP-3-CLIENTEVENTLOG: SSID XS4MOBILITY added to the slot[1]

*Oct 19 11:13:21.149: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 3 due to WMM is not enabled

*Oct 19 11:13:21.152: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Oct 19 11:13:22.147: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Oct 24 12:43:02.288: *** Access point reloading. Reason: Reload Command ***

^@

But there's something strange when I check the controller dot11radio 1 :

AIR-ILM-AP-A7-04#show controllers dot11Radio 1

Radio disabled 8

!

interface Dot11Radio1

Radio AIR-AP1140A, Base Address 0025.4542.bda0, BBlock version 0.00, Software version 3.00.75

Serial number: FOC131303M9

Number of supported simultaneous BSSID on Dot11Radio1: 16

Carrier Set: ETSI (OFDM) (EU) (-E)

Uniform Spreading Required: Yes

Configured Frequency: 0 MHz  Channel 0

Allowed Frequencies: 5180(36) 5200(40) 5220(44) 5240(48) 5260(52) 5280(56) 5300(60) 5320(64) 5500(100) 5520(104) 5540(108) 5560(112) 5580(116) 5660(132) 5680(136) 5700(140)

Listen Frequencies: 5170(34) 5180(36) 5200(40) 5220(44) 5240(48) 5260(52) 5280(56) 5300(60) 5320(64) 5500(100) 5520(104) 5540(108) 5560(112) 5580(116) 5600(120) 5620(124) 5640(128) 5660(132) 5680(136) 5700(140) 5745(149) 5765(153) 5785(157) 5805(161) 5825(165)

Beacon Flags: 0, Interface Flags 60109, Interface Events 0, Mode 9; Beacons are disabled; Probes are disabled

Configured Power: 17 dBm (level 1)

...

Regards,

Highlighted
Hall of Fame Community Legend

*Mar  1 00:00:09.233: %SOAP_FIPS-2-SELF_TEST_RAD_FAILURE: RADIO crypto FIPS self test failed at 128 bit AMAC AES encrypt for TX on interface Dot11Radio 1 -Process= "Init", ipl= 0, pid= 3

RMA the WAP.  The radio module is faulty.

View solution in original post

Highlighted

Ok thx for your answer.

Content for Community-Ad