Some devices can't connect to Cisco Aironet 1262

[isaac.mutepfe]

Hi All,

Some devices such as nokia lumia 820 - windows 8 phone, ipad 2 and Bang and Olufson speaker are failing to connect to my Cisco Aironet 1262 AP. My laptop, desktops and other phones are able to connect. Please assist.

[Saurav Lodh]

Few of the phone models have compatiblity issues with the encryption  protocols like WPa2 , wep, TKIP. which encrytion you are using? try  changing it to WPA. Hope your devices connect

[Leo Laohoo]

Start by creating an SSID with OPEN authentication.

Does the client authenticate?

If yes, then start adding encryption and security until you break them.

[Edgar Khachatrian]

I would suggest you try without encryption to test....if that works make sure when you add encryption to use WPA2 and AES (and not TKIP).....

Please rate useful posts.


Sent from Cisco Technical Support Android App

[isaac.mutepfe]

I have tried removing security, and then tried playing around with available options to no avail.

My windows phone still does not see the SSID.

[Augustgood]

in this manner :

in that wlan is enabled flags on broadcast ssid ?

[isaac.mutepfe]

My issue is with the Cisco Aironet 1260 Series

[Augustgood]

this ap is autonomous or lightweight ? is connected to a wlc ?

[isaac.mutepfe]

Autonomous, not connected to a wlc

[Scott Fella]

Post your configuration so we can review.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

[isaac.mutepfe]

ap#sh run

Building configuration...

Current configuration : 1721 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname ap

!

logging rate-limit console 9

enable secret 5 $1$KS7b$x1GR33SyMCDIWIvzJU0GN.

!

no aaa new-model

!

!

dot11 syslog

!

dot11 ssid PME1

   authentication open

   authentication key-management wpa version 2

   guest-mode

   wpa-psk ascii 7 13150541065F107933

!

!

!

username xxxx password 7 13150541065F107933

!

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm tkip

!

ssid YYYY

!

antenna gain 0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface Dot11Radio1

no ip address

no ip route-cache

!

encryption mode ciphers aes-ccm tkip

!

ssid YYYY

!

antenna gain 0

no dfs band block

channel dfs

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface GigabitEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

no keepalive

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface BVI1

ip address x.x.x.x 255.255.255.0

no ip route-cache

!

ip default-gateway x.x.x.x

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

!

!

!

line con 0

line vty 0 4

login local

!

end

[Augustgood]

put the same ssid on global config and below int dot11 radio 0.

[isaac.mutepfe]

Please assist with print screens.

[Augustgood]

Your ap is autonomous, in global config "dot11 ssid PME1" the ssid PME1 must be yyyy .

[isaac.mutepfe]

Sorry, I corrected the the SSID issue, still no solution.