Unable to disable Fastlane on SSID

[Willem de Groot]

Hi all,

Running 8.8.111.0 on an 1850 Series, with 6 SSIDs configured, I'm not able to disable the FASTLANE option by Web-GUI.
In the GUI I can select disable for the FASTLANE option and apply the settings. But entering the WLAN-setting again, the option is enabled again.

Can somebody give me the CLI command to disable FASTLANE on an SSID?

At the CLI, show WLAN 5, shows me 

QoS Fastlane Status.............................. Enabled

Thanks

Willem

[Willem de Groot]

ok, I found this command and this is the result, (Failed)

(Cisco Controller) >config qos fastlane disable 5

Warning! This command will automatically disable the WLAN and
will reset the WLAN QoS configurations to defaults (Silver profile, AVC disabled).
The WLAN will be re-enabled once the configuration completes.
Are you sure that you want to continue? (y/N)y

Error: Fastlane Configuration failed.
qos fastlane disable 5
- Success
wlan media-stream multicast-direct 5 disable
- Success
wlan qos 5 silver
- Success
wlan avc 5 profile AUTOQOS-AVC-PROFILE disable
- Failed

Reverting these configurations for WLAN.
wlan qos 5 platinum

qos fastlane enable 5

wlan avc 5 profile AUTOQOS-AVC-PROFILE enable
Reverting - Failed
***********************************************

[Leo Laohoo]

Do NOT use 8.8.111.0.
Upgrade to 8.8.120.0 first and try again.

[Willem de Groot]

Hi Leo,

Is 8.8.120.0 better?
I'll try to install and give feedback here.

[Willem de Groot]

I updated to 8.8.120.0 but the result is the same, not possible to disable FASTLANE.

Not in Web-GUI (you can change, apply but it does not disable it)

Not in CLI:

(Cisco Controller) >config qos fastlane disable 5

Warning! This command will automatically disable the WLAN and
will reset the WLAN QoS configurations to defaults (Silver profile, AVC disabled).
The WLAN will be re-enabled once the configuration completes.
Are you sure that you want to continue? (y/N)y

Error: Fastlane Configuration failed.
qos fastlane disable 5
- Success
wlan media-stream multicast-direct 5 disable
- Success
wlan qos 5 silver
- Success
wlan avc 5 profile AUTOQOS-AVC-PROFILE disable
- Failed

Reverting these configurations for WLAN.
wlan qos 5 platinum

qos fastlane enable 5

wlan avc 5 profile AUTOQOS-AVC-PROFILE enable
Reverting - Failed
***********************************************

This Profile (AUTOQOS-AVC-PROFILE)does not seem to exist.

(Cisco Controller) >show avc profile summary

Profile-Name Number of Rules
============ ==============

(Cisco Controller) >

Any Idea left?

[patoberli]

Was 8.8.111.0 the first firmware running on this AP or did you upgrade from some 8.3 software first?
If you did upgrade, try a factory reset with the mode button. Alternatively create a QoS profile with the exact shown name and then try to disable it.
Lastly you could open a TAC.

[Willem de Groot]

Hi Patoberli

I have different Environment, some may be upgraded from older, others may have been reset and started with an 8.8. release.

I could not try your solution yet, the AP is 2000KM from here, don't want to make it unavailable for me.

I'll see if I can copy the config to an test AP at my desk. This solution will definitively not have the same update history.

What I could do on my private AP, is I created an new profile with a different Name but the same SSID but without fastlane activated.

This worked fine, I deleted the first profile and renamed the new to the old name.

[patoberli]

Sounds like a plan. Please keep us updated if it works.