Mobility Services Engine (MSE) platform status check up not working
User has installed MSE on a Virtual Machine (Windows 2003 Server) and facing issues.
Getting Error while checking the state:-
It loads a little and then shows Error:-
Starting MSE Platform, Waiting to check the Status
like 10 times and then an error comes up: "Failed to get the Status"
This Error comes when:-
Configure and Save the configuration
Executing getserverinfo command
The username and password hs been changed in order to associate it with WCS but when i go into the WCS and try to set it up, it says that there is an error in the username/password whereas i am using the same previously configured information in the MSE.
WCS version is 6.0 but not sure about MSE version since it doesn't show it due to the error on the status.
User deleted the Virtual Machine where he had that MSE and downloaded the new MSE v7 as a VM workstation and now works perfectly.
How to configure RF Tags? If we have AP 1131-N-K9, why can't we use its 802.11a RF? When I do a show run it says its interface is down and I can bring it up because it mentions an error about not being compatible with a Regulatory Domain.
We have similar issues with certain AP that the a radio show down although it is admin enabled. Check on your AP if that a radio is admin disabled then you might have to enable it.
Similar Issue with MSE 7.4.100 on hardware platform.
[root@MSE ~]# /etc/init.d/msed statusSTATUS:Health Monitor is runningStarting MSE Platform, Waiting to check the status.Starting MSE Platform, Waiting to check the status.Starting MSE Platform, Waiting to check the status.
MSE stops successfully, but doesn't start
[root@MSE ~]# /etc/init.d/msed restartStopping MSE Platform .......................Flushing firewall rules: [ OK ]Setting chains to policy ACCEPT: nat filter [ OK ]Unloading iptables modules: [ OK ]Starting MSE Platform Flushing firewall rules: [ OK ]Setting chains to policy ACCEPT: filter [ OK ]Unloading iptables modules: [ OK ]Starting Health Monitor, Waiting to check the status.Health Monitor successfully startedStarting Admin process... Started Admin process. Database started successfully. Starting framework and services ...Database started successfully. Starting framework and services ..........................
If the MSE is virtual then make sure that the resources are there that is required. Many time when we mess around with lab MSE this happens and usually a restart of the VM host fixes it. A few times it was basically me bringing up a new VM or reverting back to a snapshot that worked.
Verifying the Mobility Services Engine Software State
You can verify the mobility services engine software state at any time. In the mobility services engine CLI interface, enter: /etc/init.d/msed status
If the mobility services engine is running, the command output looks like this example:
Product name: Cisco Mobility Service Engine
Hw Version: none
Hw Product Identifier: none
Hw Serial Number: none
Use HTTPS: true
HTTPS Port: 443
Use HTTP: false
HTTP Port: 80
Legacy HTTPS: false
Legacy Port: 8001
Session timeout in mins: 30
DB backup in days: 0
Start time: Wed Sept 30 15:24:36 EDT 2008
Server current time: Fri May 30 19:08:15 EDT 2008
Server timezone: America/New_York
Server timezone offset: -18000000
Service Engine (1):
NAME: Location Service
Location Service Monitor
Log Modules: 262143
Log Level: INFO
Days to keep events: 2
Keep absent data in mins: 1440
Used Memory (bytes): 129851856 Allocated Memory (bytes): 3087007744
Max Memory (bytes): 3087007744
DB virtual memory (kbytes): 0
DB virtual memory limit (bytes): 256000000
DB disk memory (bytes): 4128768
DB free size (kbytes): 2856
Active Elements: 0
Active Clients: 0
Active Tags: 0
Active Rogues: 0
Active Elements Limit: 18000
Active Sessions: 0
Clients Not Tracked due to the limiting: 0
Tags Not Tracked due to the limiting: 0
Rogues Not Tracked due to the limiting: 0
Total Elements Not Tracked due to the limiting: 0
If the mobility services engine is not running, the command output looks like this example:
com.aes.common.util.AesException: Failed to connect to server: http://localhost:8001 at com.aes.client.AesClient.connect(AesClient.java:218) at com.aes.location.test.AesAbstractTest.init(AesAbstractTest.java:181) at com.aes.location.test.admin.AesTestGetServerInfo.main(AesTestGetServerInfo.java:75) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at com.zerog.lax.LAX.launch(DashoA8113) at com.zerog.lax.LAX.main(DashoA8113)
I am a student at Pioneer Technology Center, Ponca City, Oklahoma. We have a Cisco 1950 Series wireless router that we wish to configure as a wireless hotspot. I am interested in how the router manages wireless connections and I would like to see a diagra...
Hello All, Having a very difficult time getting my 1702i AP to join WLC 2504. This is working fine when direct connected to PoE port on device, but when I attempt to connect to edge switchport (configured for same VLAN as AP-manager) the connec...
I am trying to setup evaluation licenses on a Catalyst 9800-CL appliance. I was told all you have to do was registered it under your Cisco smart account, and it will automatically activate the evaluation licenses for the appliance under your account. I re...
I borrowed a 'Cisco SG300-10 10 port gigabit managed switch' from work to practice things i'm learning from my CCNA course. I have tried a serial to ethernet cable for console connection, and a regular ethernet cable from one of the ports. I have tri...