cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Cisco Community Designated VIP Class of 2020

347
Views
10
Helpful
10
Replies
Highlighted
Beginner

1131ap not appearing in 2504 gui

Hi,

 

I have 9 access points of different models connected to my 2504 wlc. Currently, the CAP3502I and three LAP1141N have successfully joined the mobility group. Whereas there are three LAP1131AG and one AP1131AG are not listed in the gui.

 

I have recently converted these AP from LWAPP firmware to autonomous firmware. 

 

Troubleshooting from the ap perspective, they seem to get valid IP addresses from my dhcp router.

 

Please let me know if you need any outputs. Thanks!

 

Everyone's tags (2)
1 ACCEPTED SOLUTION

Accepted Solutions
Participant

Re: 1131ap not appearing in 2504 gui

If you run the AP's on autonomous IOS (k9w7) images, then they won't be able to join the WLC, they need to be on k9w8 which is the lightweight AP image.

 

<<< Please help the community by marking useful posts helpful, or accept as a solution if it resolved your issue >>>

View solution in original post

10 REPLIES 10
Hall of Fame Community Legend

Re: 1131ap not appearing in 2504 gui

Post the complete output to the following commands:
1. WLC: sh sysinfo;
2. WLC: sh time;
3. AP: sh version; and
4. AP: sh ip interface brief
Beginner

Re: 1131ap not appearing in 2504 gui

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.2.111.3
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 15.0


Build Type....................................... DATA + WPS

System Name...................................... WLC
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.10.1.3
Last Reset....................................... Power on reset
System Up Time................................... 0 days 2 hrs 51 mins 46 secs
System Timezone Location......................... (GMT +9:30) Darwin

Configured Country............................... AU  - Australia
Operating Environment............................ Commercial (0 to 40 C)

--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +30 C
External Temperature............................. +34 C
Fan Status....................................... 3432 rpm

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0

Burned-in MAC Address............................ D0:C2:82:E0:8F:80
Maximum number of APs supported.................. 10
Beginner

Re: 1131ap not appearing in 2504 gui

(Cisco Controller) >show time

Time............................................. Wed Mar 27 22:17:03 2019

Timezone delta................................... 0:0
Timezone location................................ (GMT +9:30) Darwin

NTP Servers
    NTP Polling Interval.........................     3600

     Index     NTP Key Index     NTP Server      NTP Msg Auth Status
    -------  ---------------------------------------------------------------
Beginner

Re: 1131ap not appearing in 2504 gui

AP0017.95b0.c82c# sh ver
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 02:44 by prod_rel_team

ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)

AP0017.95b0.c82c uptime is 2 hours, 50 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w7-mx.124-25d.JA1/c1130-k9w7-mx.124-25d.JA1"

cisco AIR-AP1131AG-N-K9    (PowerPCElvis) processor (revision A0) with 25590K/7168K bytes of memory.
Processor board ID FHK1018C0CD
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:17:95:B0:C8:2C
Part Number                          : 73-8962-09
PCA Assembly Number                  : 800-24818-08
PCA Revision Number                  : A0
PCB Serial Number                    : FOC10170ZMR
Top Assembly Part Number             : 800-25544-06
Top Assembly Serial Number           : FHK1018C0CD
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1131AG-N-K9

Configuration register is 0xF
VIP Mentor

Re: 1131ap not appearing in 2504 gui

Convert these AP in capwap mode.

 

You are still using Autonomus image.(

flash:/c1130-k9w7-mx.124-25d.JA1/c1130-k9w7-mx.124-25d.JA1"

)

Beginner

Re: 1131ap not appearing in 2504 gui

AP0017.95b0.c82c#sh ip int bri
Interface IP-Address OK? Method Status Protocol
BVI1 10.10.1.13 YES DHCP up up
Dot11Radio0 unassigned YES NVRAM administratively down down
Dot11Radio1 unassigned YES NVRAM administratively down down
FastEthernet0 unassigned YES NVRAM up up
Participant

Re: 1131ap not appearing in 2504 gui

If you run the AP's on autonomous IOS (k9w7) images, then they won't be able to join the WLC, they need to be on k9w8 which is the lightweight AP image.

 

<<< Please help the community by marking useful posts helpful, or accept as a solution if it resolved your issue >>>

View solution in original post

Beginner

Re: 1131ap not appearing in 2504 gui

sounds good for a try, i will try it tomorrow and will mark as solution . .  Thanks

Hall of Fame Community Legend

Re: 1131ap not appearing in 2504 gui

Time and date of the controller is incorrect.
Configure NTP.
Beginner

Re: 1131ap not appearing in 2504 gui

the time of my controller is correct, so is the AP. It is the first thing I configure on controller as it does not retain upon reboot.

 

I have not set up ntp for my network so i would use manual config for now.

CreatePlease to create content
Content for Community-Ad

August's Community Spotlight Awards