08-27-2014 05:05 PM - edited 07-05-2021 01:27 AM
Dear all,
Appreciate that anyone know how to configure mac authentication in 1941w router?
Perhaps can show me some example of configure mac authentication in 1941w router.
Solved! Go to Solution.
08-31-2014 05:17 PM
If your trying to configure mac filtering on the access point in the 1941w and the AP is autonomous, you can follow this guide:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116582-configure-ap-00.html
Scott
08-31-2014 05:34 PM
Hi,
For MAC filtering In case of autonomous AP creating access-list, use the below command
Test-AP# configure terminal
Test-AP(conf)# access-list 700 deny <mac-address you want filter/deny>
For light weight follow the below process:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/4-2/configuration/guide/ccfig42/c42lwap.html#wp1115915
Thanks & Regards
Sandeep
08-29-2014 09:45 AM
Hi,
Below is the configuration for mac authentication bypass on cisco 1900 router
c1921> enable
c1921# configure terminal
c1921(conf)#interface gigabitethernet slot / port
c1921(conf-if)# authentication port-control auto
c1921(conf-if)# mab
c1921(conf-if)# end
> You can verify using the below command
c1921#show authentication sessions
Interface MAC Address Method Domain Status Session ID
Gi0/1 0201.0201.0201 mab DATA Authz Success 0303030300000004002500A8
c1921#show authentication sessions interface Gi0/1
Interface: GigabitEthernet0/1
MAC Address: 0201.0201.0201
IP Address: Unknown
User-Name: 02-01-02-01-02-01
Status: Authz Success
Domain: DATA
Oper host mode: single-host
Oper control dir: both
Authorized By: Authentication Server
Vlan Group: N/A
AAA Policies:
Session timeout: N/A
Idle timeout: N/A
Common Session ID: 0303030300000004002500A8
Acct Session ID: 0x00000007
Handle: 0x3D000005
Runnable methods list:
Method State
mab Authc Success
For more details refer the below link:
http://www.cisco.com/c/en/us/td/docs/routers/access/1900/software/configuration/guide/Software_Configuration/conf.pdf
Thanks & Regards
Sandeep
08-31-2014 04:34 PM
Hi Sandeep,
Thanks for your document.
But this is the mac authentication bypass. How about if I want to control user authentication by manual configure mac address in authentication to control the wifi access?
Best regards
TPPSupport
08-31-2014 05:17 PM
If your trying to configure mac filtering on the access point in the 1941w and the AP is autonomous, you can follow this guide:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116582-configure-ap-00.html
Scott
08-31-2014 07:27 PM
Thanks guys,
I able to use the mac-list to control the mac address filtering.
08-31-2014 05:34 PM
Hi,
For MAC filtering In case of autonomous AP creating access-list, use the below command
Test-AP# configure terminal
Test-AP(conf)# access-list 700 deny <mac-address you want filter/deny>
For light weight follow the below process:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/4-2/configuration/guide/ccfig42/c42lwap.html#wp1115915
Thanks & Regards
Sandeep
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide