10-27-2014 06:29 AM - edited 07-05-2021 01:48 AM
Hello,
I am having a simple issue associating to my stand alone Cisco 2702. Debug displays the following output:
*Mar 1 02:07:50.471: 3D75990E r 5 29/34/39/37 63- B000 07F 69E300 D168DC 69E300 F0D0 auth l 17
algorithm 0
sequence 1
status 0
221 - 0 10 18 2 0 0 0 0 0
*Mar 1 02:07:50.471: 3D759B9B t 11 0 - B000 000 D168DC 69E300 69E300 0000 auth l 6
algorithm 0
sequence 2
status 0
*Mar 1 02:07:50.471: 3D759CC2 r 5 30/35/40/39 45- 0000 07F 69E300 D168DC 69E300 F0E0 assreq l 69
cap 31 infra privacy shorthdr
listen interval 15
ssid Truckcam_internal
rates B 96
rsn1 mcst aes ucst aes keymgmt wpa2-psk cap C00
221 - 0 10 18 2 0 0 0 0 0
221 - 0 50 F2 2 0 1 0
*Mar 1 02:07:50.475: 3D759F38 t 11 0 - 1000 000 D168DC 69E300 69E300 0000 assrsp l 8
cap 0
status 25
aid C000
rates
It's a simple one SSID setup with WPA2 PSK. I've tried to connect with both IPhone and Windows 8 PC.
Configuration...
...
dot11 vlan-name SSID vlan 1
!
dot11 ssid SSID
vlan 1
band-select
authentication open
authentication key-management wpa version 2
guest-mode
mbssid guest-mode
mobility network-id 492
wpa-psk ascii 12345678
information-element ssidl
!
!
!
interface Dot11Radio0
no ip address
!
encryption vlan 1 mode ciphers aes-ccm
!
broadcast-key vlan 1 change 10000 membership-termination
!
ssid Truckcam_internal
!
antenna gain 0
stbc
speed 5.5 basic-11.0
power local 7
channel 2472
fragment-threshold 2340
station-role root access-point
rts threshold 2312
no cdp enable
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
mac-address f07f.068d.12ec
ip address 172.20.20.42 255.255.255.0
ipv6 enable
!
ip default-gateway 172.20.20.1
!
Thanks,
Solved! Go to Solution.
10-29-2014 02:17 AM
Hi
Did you erase the previous config & load the given config ? or modified your existing configs.
If you haven't delete your existing config try that first
AP#erase startup-config
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
AP#reload
System configuration has been modified. Save? [yes/no]: no
Proceed with reload? [confirm]
Once you load the new config, test each band seperately (ie shutdown radio0 & test, then shut radio1 while enable radio0 & test). See whether issue is in both bands ? Also test with different type of client as well.
HTH
Rasika
**** Pls rate all useful responses ****
10-27-2014 11:20 AM
Hi
You can try a simple configuration like below. Your configuration has some incompatible configs (eg 5.5 & 11Mbps data rate with WPA2/AES)
1. Take a backup of your existing configuration
2. Erase the startup config & reload the AP to come up with zero config.
3. Then configure it like below & give it a try.
dot11 ssid Truckcam_internal
vlan 1
authentication open
authentication key-management wpa version 2
wpa-psk ascii 12345678
mbssid guest-mode
!
interface Dot11Radio0
encryption vlan 1 mode ciphers aes-ccm
ssid Truckcam_internal
mbssid
no shut
!
interface Dot11Radio1
encryption vlan 1 mode ciphers aes-ccm
ssid Truckcam_internal
mbssid
channel width 40-above
no shut
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
!
interface Dot11Radio1.1
encapsulation dot1Q 1 native
bridge-group 1
!
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
bridge-group 1
!
interface BVI1
ip address 172.20.20.42 255.255.255.0
ip default-gateway 172.20.20.1
HTH
Rasika
**** Pls rate all useful responses ****
10-28-2014 08:36 AM
Hello,
Thanks for your reply! Still the same issue though :(
dot11 vlan-name TruckCam vlan 1
!
dot11 ssid Truckcam_internal
vlan 1
band-select
authentication open
authentication key-management wpa version 2
guest-mode
mbssid guest-mode
mobility network-id 1
wpa-psk ascii 7 <HIDDEN>
information-element ssidl
!
interface Dot11Radio0
no ip address
!
encryption vlan 1 mode ciphers aes-ccm
!
ssid Truckcam_internal
!
stbc
mbssid
speed basic-1.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2472
station-role root
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
no ip address
!
encryption vlan 1 mode ciphers aes-ccm
!
ssid Truckcam_internal
!
no dfs band block
stbc
mbssid
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23. a1ss7 a2ss7 a3ss7
channel width 40-above
channel dfs
station-role root
!
interface Dot11Radio1.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
mac-address f07f.068d.12ec
ip address 172.20.20.42 255.255.255.0
ipv6 enable
!
*Mar 1 03:00:09.547: F891F88B r 1 52/47/47/52 39- B000 13A 69E300 6E0868 69E300 52C0 auth l 17
algorithm 0
sequence 1
status 0
221 - 0 10 18 2 0 0 1 0 0
*Mar 1 03:00:09.547: F891FD04 t 1 0 - B000 2900 6E0868 69E300 69E300 0000 auth l 6
algorithm 0
sequence 2
status 0
*Mar 1 03:00:09.551: F89201B1 r 1 52/47/48/52 48- 0000 13A 69E300 6E0868 69E300 52D0 assreq l 86
cap 431 infra privacy shorthdr
listen interval 10
ssid Truckcam_internal
rates 82 12 18 24 30 48 60 6C
pwr cap min 8 max 17
suppd chans 1 D
rsn1 mcst aes ucst aes keymgmt wpa2-psk cap C00
extrates C
221 - 0 10 18 2 0 0 1 0 0
221 - 0 50 F2 2 0 1 0
*Mar 1 03:00:09.551: F892062D t 1 0 - 1000 000 6E0868 69E300 69E300 0000 assrsp l 8
cap 0
status 25
aid C000
rates
10-29-2014 02:17 AM
Hi
Did you erase the previous config & load the given config ? or modified your existing configs.
If you haven't delete your existing config try that first
AP#erase startup-config
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
AP#reload
System configuration has been modified. Save? [yes/no]: no
Proceed with reload? [confirm]
Once you load the new config, test each band seperately (ie shutdown radio0 & test, then shut radio1 while enable radio0 & test). See whether issue is in both bands ? Also test with different type of client as well.
HTH
Rasika
**** Pls rate all useful responses ****
10-31-2014 02:08 AM
Reconfiguration did it. The problem was that the AP was not on premise so I could reset it whitout having a console plugged in.
Funny thing though is that I reloaded it and applied the exact same configuration on it via the CLI. It seems like something happened in the background when I configured via GUI during the first run.
Anyway, now everything works great. Thank you guys... and Cisco for your help! :)
10-31-2014 02:45 AM
Hi
Good to see that you got it working. Thanks for using rating as well
Rasika
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: