cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2032
Views
0
Helpful
8
Replies
Highlighted

Cisco MSE in the NCS

Hello,

I have an MSE configured in de NCS. The MSE is reachable from the NCS. When I go in the NCS to the tab Home -> Context Aware, I don't see anything. When I restart the MSE I will see some data in the screen. But no new data is apearing in the screen.

I guess that is has something to do with de SNMP community. In the NCS and WLC the community is our own community. In the MSE the community is public. The IP-address of the NCS is configured in the MSE as server who may change to MSE.

When I try to change the community from public to our own, it is not possible. Also when I make an new one, the ip- address must be not te same as the one, wich all ready has configured.

Can I change with the CLI the SNMP community in the MSE??

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Master

The version can be found in NCS... In NCS, help about will give you the NCS version. Then look at the MSE from NCS, there you will see the version of the MSE. What version is your WLC also. The NCS and MSE should be equal or a higher version than the WLC.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

View solution in original post

8 REPLIES 8
Highlighted
Hall of Fame Master

Not from the CLI of the MSE.  If you rerun the startup script or wizard, you don't have any snmp entries.  The only entry hat you can change is the communications and password to the WCS/NCS.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
Highlighted

What version is your NCS and your MSE on.  On the MSE, if you run the /etc/init.d/msed status do you see the service up?

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***
Highlighted

MSE Version: MSE-3355-K9:V01

NCS Version: V01

output:

MSE Platform is up, getting the status

-------------

Server Config

-------------

Product name: Cisco Mobility Service Engine

Version: 7.0.201.204

Hw Version: V01

Hw Product Identifier: AIR-MSE-3355-K9

Hw Serial Number:XXXXXXXX

Use HTTP: false

Legacy HTTPS: false

Legacy Port: 8001

Log Modules: -1

Log Level: INFO

Days to keep events: 2

Session timeout in mins: 30

DB backup in days: 2

-------------

Services

-------------

Service Name: Context Aware Service

Service Version: 7.0.200.204

Admin Status: Enabled

Operation Status: Up

Service Name: Wireless Intrusion Protection Service

Service Version: 1.0.2077.0

Admin Status: Enabled

Operation Status: Up

--------------

Server Monitor

--------------

Server start time: Mon Sep 24 14:27:52 CEST 2012

Server current time: Thu Oct 04 08:54:30 CEST 2012

Server timezone: Europe/Amsterdam

Server timezone offset: 3600000

Restarts: 6

Used Memory (bytes): 121530728

Allocated Memory (bytes): 535887872

Max Memory (bytes): 1908932608

DB virtual memory (kbytes): 0

DB virtual memory limit (bytes): 0

DB disk memory (bytes): 1850230400

DB free size (kbytes): 0

---------------

Active Sessions

---------------

Session ID: 29994

Session User ID: 2

Session IP Address: x.x.x.x

Session start time: Mon Sep 24 14:31:24 CEST 2012

Session last access time: Thu Oct 04 08:51:26 CEST 2012

-------------

Context Aware Service

-------------

Total Active Elements(Wireless Clients, Tags, Rogue APs, Rogue Clients, Interferers, Wired Clients): 0

Active Wireless Clients: 0

Active Tags: 0

Active Rogue APs: 0

Active Rogue Clients: 0

Active Interferers: 0

Active Wired Clients: 0

Active Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Clients, Tags) Limit: 6000

Active Sessions: 1

Wireless Clients Not Tracked due to the limiting: 0

Tags Not Tracked due to the limiting: 0

Rogue APs Not Tracked due to the limiting: 0

Rogue Clients Not Tracked due to the limiting: 0

Interferers Not Tracked due to the limiting: 0

Wired Clients Not Tracked due to the limiting: 0

Total Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Clients) Not Tracked due to the limiting: 0

-------------------------

Context Aware Sub Services

-------------------------

Subservice Name: Aeroscout Tag Engine

Admin Status: Disabled

Operation Status: Down

Subservice Name: Cisco Tag Engine

Admin Status: Enabled

Operation Status: Up

Highlighted
Hall of Fame Master

The version can be found in NCS... In NCS, help about will give you the NCS version. Then look at the MSE from NCS, there you will see the version of the MSE. What version is your WLC also. The NCS and MSE should be equal or a higher version than the WLC.

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

View solution in original post

Highlighted

MSE Version:

7.0.201.204

WLC:

Software Version7.2.110.0

NCS: 

Version: 1.1.0.58 ( - Jan. 27, 2012 - rev 60272)

Highlighted

so I must update everything to 7.3?

Before it will work proberbly?

Highlighted

No... Look at this matrix and you will see what version of NCS and MSE us required for the WLC code you have.

http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Highlighted

NCS has to be 1.1.1.24

MSE has to be 7.2.110.0

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***