cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1225
Views
5
Helpful
4
Replies

Univeral Workgroup bridge Access Point

Maurice Ball
Level 3
Level 3

I need to set up a universal workgroup bridge access point on a mobile forklift. My issue is the customer would like to use a username and password combination for authentication on the wireless network that the workgroup bridge access point will be connecting too. Is it possible to set up the workgroup bridge to authenticate with a username and password?

2 Accepted Solutions

Accepted Solutions

Haydn Andrews
VIP Alumni
VIP Alumni

Hi

 

You can configure the WGB to connect via PSK or 802.1x

 

https://www.cisco.com/c/en/us/support/docs/wireless-mobility/service-set-identifier-ssid/211293-Configure-Work-Group-Bridge-WGB-Multip.html

https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/201044-802-1x-authentication-with-PEAP-ISE-2-1.html

Note this is with the WGB connecting to a WLC based AP.

 

Example using PEAP auth (username and password)

https://www.cisco.com/c/en/us/support/docs/wireless/virtual-wireless-controller/115736-wgb-peap-00.html

*****Help out other by using the rating system and marking answered questions as "Answered"*****
*** Please rate helpful posts ***

View solution in original post

Sandeep Choudhary
VIP Alumni
VIP Alumni

If you are using wlc then use this link to configure the AP as WGB:

 

https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/68472-configure-wgb-00.html

 

WGB with autonomous AP:

 

https://mrncciew.com/2018/05/25/wgb-with-peap/

 

Regards

Dont forget to rate helpful posts

View solution in original post

4 Replies 4

Hi.

 

 Take a look here. Section "Configuring Workgroup Bridge Mode"

 

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/15-3-3/configuration/guide/cg15-3-3/cg15-3-3-chap19-wgb-standby.html#pgfId-1084424

 

 

-If I helped you somehow, please, rate it as useful.-

Haydn Andrews
VIP Alumni
VIP Alumni

Hi

 

You can configure the WGB to connect via PSK or 802.1x

 

https://www.cisco.com/c/en/us/support/docs/wireless-mobility/service-set-identifier-ssid/211293-Configure-Work-Group-Bridge-WGB-Multip.html

https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/201044-802-1x-authentication-with-PEAP-ISE-2-1.html

Note this is with the WGB connecting to a WLC based AP.

 

Example using PEAP auth (username and password)

https://www.cisco.com/c/en/us/support/docs/wireless/virtual-wireless-controller/115736-wgb-peap-00.html

*****Help out other by using the rating system and marking answered questions as "Answered"*****
*** Please rate helpful posts ***

Thanks for the quick reply.

Sandeep Choudhary
VIP Alumni
VIP Alumni

If you are using wlc then use this link to configure the AP as WGB:

 

https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/68472-configure-wgb-00.html

 

WGB with autonomous AP:

 

https://mrncciew.com/2018/05/25/wgb-with-peap/

 

Regards

Dont forget to rate helpful posts

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: