1532E unable to join 9800 controller

[JWHolm81891]

So, I've been configuring new APs all week without a hitch, then there's this guy. A 1532E, this one is not out of the box but was previously on a 5500 controller we are phasing out. I wiped the AP back to factory settings knowing that APs can be sticky. I'm just not able to get this one to populate in the AP table so I can configure through the GUI. Here are the logs. Any thoughts?

*Jun 23 14:41:32.331: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 23 14:41:32.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:32.335: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:32.335: %CAPWAP-5-SENDJOIN: sending Join Request to 10.7.230.2
*Jun 23 14:41:32.339: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.7.230.2
*Jun 23 14:41:32.931: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 23 14:41:32.931: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 23 14:41:33.619: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jun 23 14:41:33.627: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jun 23 14:41:34.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jun 23 14:41:34.655: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 23 14:41:34.663: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jun 23 14:41:34.671: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jun 23 14:41:35.655: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jun 23 14:41:35.663: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 23 14:41:35.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 23 14:41:36.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 23 14:41:42.927: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 23 14:41:43.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:43.323: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.7.230.2 peer_port: 5246
*Jun 23 14:41:43.327: %CAPWAP-5-SENDJOIN: sending Join Request to 10.7.230.2
*Jun 23 14:41:43.327: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.7.230.2
*Jun 23 14:41:43.327: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.7.230.2:5246
*Jun 23 14:41:43.327: %CAPWAP-3-ERRORLOG: Go join a capwap controller

[balaji.bandi]

what is the WLC 9800 code running, have you checked the matrix it supported.

[JWHolm81891]

Nope.

[Flavio Miranda]

Hi

  This AP 1532E does show on the compatibility matrix for IOS XE.

[Leo Laohoo]

The other forum have already responded to this very same question:  1530 is not supported in the 9800.

[jonathga94]

The AP 1530 is not supported on the WLC 9800