12-20-2015 05:38 AM - edited 07-05-2021 04:25 AM
Hello,
we have WLC 5508 with 50 AP registered and a new WLC 5508 , we need to cluster the the WLCs in HA but thy will be in different switches but in same VLAN
-how can RP port will be connected to each other via switches
-do we need any modification in the registered 50th APs after making the HA
12-21-2015 12:04 AM
Hi Mahmoud,
Regarding WLCs in different location : It is required for us to have direct physical connectivity between the two WLCs via the redundancy port and also they should have management IP in same subnet. The distance between the two WLCs can got upto 100 metres as per the cabling standard.
If the distance between the two locations is higher than this and if cabling is not possible between two WLCs then you can consider old AP failover feature.
http://mrncciew.com/2013/04/07/ap-failover/
If you want then you can manually assign the primary and secondary WLC IP to each AP but this is not a must.
Regards
Dont forget to rate helpful posts
12-21-2015 02:39 AM
thank sandeep for your reply
WLCs at our solution must be distributed between switches so correct the blow
-we have 50 AP license at each WLC will it be 100 after HA?
-what conf need to be done from APs sides?
12-21-2015 03:07 AM
Hi Mahmoud,
VlanY Redundancy Port (RP) via switches
As per knowledge, The RP needs to be connected on a direct link.
we have 50 AP license at each WLC will it be 100 after HA?
Yes, If you are using two wlc as seperately then yes total count will be 100(50 on each wlc).
No if you are using as HA: it will be only 50 AP
primary wlc: AIR-CT5508-50-K9 and secondary: AIR-CT5508-HA-K9
then you will have only 50 AP license.
Regards
Dont forget to rate helpful posts
12-21-2015 06:02 AM
Hello Sandeep
I have read a document from cisco that said we can use different switches as blow
http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html#pgfId-78161
what additional conf need to be at switches configuration
-all of my WLCs have base-ap-count 50 so after ha license will be 50 or 100?
12-21-2015 06:58 AM
Hi,
Thta is for WISM-2 not for 5508 wlc.
Note A direct physical connection between Active and Standby Redundant Ports is highly recommended.
-all of my WLCs have base-ap-count 50 so after ha license will be 50 or 100?
1.You have both WLC in normal mode so need one WLC must convert to HA-SKU mode(It require minimum 50 AP license)
2.After converting to HA, then you can start configuring AP SSO or HA between these two controllers.
3. After connection, you will have 50 AP license on primary and secondary wlc will takeover in case if primary is down.
Now understand the failover case when you have One WLC has a valid AP Count (50 AP)license and the other WLC has a HA SKU UDI.
so in HA mode you can only use 50 AP max practically.
Regards
Dont forget to rate helpful posts
01-23-2016 01:29 PM
after converting 2 WLCs to HA what IP should APs pointed to
in other word what configuration change should be done from APs side
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide