01-19-2017 06:49 AM - edited 07-05-2021 06:24 AM
Final code 8.2.151.0 is now posted, thanks for your interest!
New Updated version 8.2.145.64
This release adds the following functionality:
CSCvc18129 Crash on RF profile/client exclusion sync on HA scenario
CSCvd19354 WLC crash while editing config rf-profile hsr-mode disable | enable config rf-profile 11b
CSCvd20843 Beacon stuck due to off-channel stuck
CSCvd25183 2800/3800 does not advertise the extension channel correctly when DCA assigns Bandwidth.
CSCvd29298 2800/3800 - Type 3 off-channel stuck due to callback missing during off-channel
CSCvd07243 Unable to change AP name nor location from the GUI
CSCvc87207 AP2800 802.11b/g radio dropping RTP packets
CSCvd16523 AP3800/2800: New CLI to make core dump extended not persistent across upgrade
CSCvc59252 1852 AP showing only power level 1 instead of power level 1 to 8 under 5 Ghz radio
CSCvd16939 1800 Band-Select does not work
CSCvd16993 2800/3800 - Rxhang Fixes
CSCvb94413 2800/3800 - Fix DAA
CSCvd00405 Silent reboot observed for 3800
CSCvd07657 AP1810 fails to get ARP response intermittently leading to a full reboot
CSCvd18791 2800/3800 - NSS counters after next-hop-MAC failure in capwapd
CSCva91457 WLC: repeated crashes w/Reason: spamApTask4
CSCvc52619 Local EAP do not support any of ciphers, used by 8821 phone
CSCvb77682 2800/3800 - ioctl error message when setting XOR to 5GHz band
CSCvb73104 AP 1600: Radio d1 reset: FW: irq/mac stat=40000/10000000 command timeout
CSCvd07215 1800/2800/3800 doesn't learn dhcp lease time from dhcp server and defaults to 24hr.
CSCvd09482 2800/3800 - Rxhang Fixes
CSCvd03656 AP2800/3800 not updating ndp to WLC due to Status: NSS_INVALID_PARAM
CSCvd05596 2800/3800 - Rxhang Fixes
CSCvb94799 | mc2uc packet packet lost with AP 3802E |
CSCvc89939 | 2800/3800: 40 mhz ext offset 8.2.145.33 |
CSCvc90559 | 2800/3800: RX Hang seen on alpha 8.2.145.36 |
CSCvc61560 | WLC radius auth aaaQueueReader "Unable to fit Radius packet in allocated memory" |
CSCvb78834 | wlc crashing with task name emweb |
CSCvc64343 | AP1530 detected a lot of radars |
CSCvc60233 | 2800/3800: Off-channel timeout is observed |
CSCvc86514 | 2800/3800 - AP CAPWAP reset when extended Radio coredump is enabled |
CSCvc81662 | 2800/3800: RX Hang seen on alpha 8.2.145.26 |
CSCvc71905 | 2800/3800: AP detects radar in the absence of radar sources (8.2.131.40) |
CSCvc81491 | 2800/3800: high latency issues on on build 8.2.145.26 |
CSCvb94436 | TKIP support for 1800 series APs |
CSCvc52004 | 1800: iOS device connect to the dot1x network slowly |
CSCvc70133 | 1800/2800/3800: AP flex: MC40 11g client sending Assoc req with g rates in extended rates display issue |
CSCvc80161 | 2800/3800 11n/ac clients failing to associate with XOR in 5GHz |
CSCvc11544 | Default Neighbor Pruning Timer need to be increased to keep neighbor entries for 1 hour |
CSCvc76148 | 2800/3800 Beacon drift causing mc9060 client drops |
CSCur63031 |
AP error: %ENTROPY-0-ENTROPY_ERROR: Unable to collect sufficient entropy |
CSCur68316 |
802AP-891 in flexconnect mode are losing vlan mapping after power cycle |
CSCuw41092 |
AP not send traffic indication in beacon for power-save client after FT |
CSCux48308 |
Broadcast delivery stops with key rotation 1552 rap, 819W 153.3JBB5 wgb |
CSCux51833 |
Client fails on RAP with AAA Override ACL when AP is in Flex+Bridge Mode |
CSCux78389 |
Radius Failover should failover both authacct server on WLAN |
CSCux85357 |
WLC sends GARP for flex local switching clients after HA switch-over |
CSCux88967 |
On MAC Filter failure Client session timeout can not association back |
CSCux95319 |
Roaming central to local auth causes in flex caused dot1x table failures |
CSCux96500 |
WiSM2/WLC crash on bcastReceiveTask |
CSCuy30583 |
5520 show imm chassis shows no results and crashes WLC |
CSCuy53072 |
SNMP cLMobilityGroupMembersTable returns wrong value from WLC in PI |
CSCuy53596 |
CleanAir fatal error and radio reset on Flex+Bridge AP |
CSCuy64520 |
Access Points (AP) sending CDP packets to the wireless clients |
CSCuy71409 |
Client detailed params not synced to standby in fast ssid scenario. |
CSCuy75241 |
5508 system crash with task mmMobility |
CSCuy82849 |
Memory leak found@mm_heartbeat module on Guest anchor WLC |
CSCuz05218 |
Barbados: show ap auto-rf does not display xor slot(0) neighbors |
CSCuz11717 |
3-sec delay before sending "dot1x auth initiate" to SPAM with WSSI |
CSCuz16883 |
Address registration issues for mobility scenarios |
CSCuz18811 |
Flex: Local Switching WLAN is changing to Central Switching WLAN on add |
CSCuz33818 |
profiler: double free issue |
CSCuz35221 |
Mobility handoff fails in new mobility dot1x CWA client reconnect |
CSCuz40066 |
Guest Anchor:Foreign to Foreign roam fails on GA scenario |
CSCuz40970 |
8510 anchor WLC Crash on task osapiBsnTimer |
CSCuz49968 |
8.0 MR4 WLC crash during SNMP set opeartion |
CSCuz50774 |
WLC lossing pings to itlsef Reaper cleaning up exited task osapi_ping_rx |
CSCuz67292 |
Client not moving to RUN state after CAS perform posturing on client |
CSCuz77747 |
Flexconnect: AP 1602 loses native vlan config on reload |
CSCuz78555 |
Bulk sync status "In-progress" after standby boots up |
CSCva01578 |
BARBADOS Ap not showing Syslog Server ip with DHCP option-7 |
CSCva01762 |
AP1815/50: Over-ride Global credentials cleared on GUI after reboot |
CSCva03376 |
UX-AP3702i After primed carrier set 5GHz only allowing four UNII3 ch |
CSCva22440 |
3800: QBSS STA Count keeps incrementing with STA associating again |
CSCva28211 |
AireOS UX AP : 'JP' should be used as world mode in Beacon/Probe Res |
CSCva28524 |
WLC 8.3 - Creating SNMP community fails |
CSCva31178 |
AP: 8.3 - Radio reset due to offchannel stuck |
CSCva32411 |
Clients losing connectivity when reauth with DOT1X over 702w AP |
CSCva48201 |
Unable to set static IP for AP from controller GUI |
CSCva52825 |
2800/3800 does not do PMTU discovery during join/image download |
CSCva63541 |
2/3800 AP CAPWAP restarts continuously during FTP transfer of large file |
CSCva72724 |
AP2602 Crash "disc_tx_requeue_client" "dot11_get_rate_shift" |
CSCva74487 |
8540 crash on running show commands task :emWeb |
CSCva74927 |
Barbados Flex - AP disjoins with 'Failed to get ARP entry for WLC' error |
CSCva83234 |
Barbados : Kernel Crash during image download |
CSCva83884 |
WLC System crash on aaaQueueReader |
CSCva87295 |
Flex AP radio reset during FT with Central dhcp and Nat-pat enabled |
CSCva90343 |
Unable to do VLAN to RLAN mapping at FlexConnect Group |
CSCva95251 |
DSCP traffic is not limited to maximum QoS Profile value |
CSCvb09381 |
Unable to add or modify SNMP strings on a 5520 HA Pair running 8.1.122.0 |
CSCvb25233 |
Enable VLAN-RLAN Mapping in FlexConnect Group |
CSCvb28231 |
Controller crashed due to memory corruption |
CSCvb35173 |
Barbados: Radio crash beacon stuck - due to lost txq reference |
CSCvb43105 |
Barbados outer DSCP not same as inner with DSCP Trust upstream NSS |
CSCvb44169 |
emWeb reaper reset after "clear mdns service-database all" |
CSCvb44699 |
NMSP queue full due to Rouge AP task. |
CSCvb48603 |
Evaluation of wlc for Openssl September 2016 |
CSCvb52310 |
Silent Boot on 2800/3800 |
CSCvb54166 |
Malformed 11v element on HSR WGB with WLC 8.2+ |
CSCvb66080 |
VLAN override from ISE is not working for RLAN with FlexConnect Local Switching |
CSCvb69962 |
Client traps not showing session ID's |
CSCvb71168 |
RSA256-AES256 dtls encryption lowers PMTU but AP doesnt' respect it |
CSCvb72380 |
performance profile show all values as 0 after clear config for XOR radio |
CSCvb79274 |
WGB wired client expiring periodically |
CSCvb80511 |
CWA is not working for flex-bridge APs pointing ACL rx from Radius doesn't exist |
CSCvb81003 |
WLC crashes as emWeb uses 100% |
CSCvb81359 |
WLC 8540 HA. RMI ping and access to standby fail when using non-default ap-manager |
CSCvb85576 |
Evaluation of wlc for CVE-2016-5195 (DIRTY CoW) |
CSCvb89781 |
2700-B AP unable to join WLC: Unable to create temp dir "flash:/update" LR= 0xc011e2dc |
CSCvb90403 |
AP1810W hardware watchdog reset at PC= 0xc03b3ffc |
CSCvb90793 |
AP name unknown in SNMP bsnDot11StationDeauthenticate traps |
CSCvb92562 |
Evaluation of all for Openssl 1.0.1 September 2016 |
CSCvb94610 |
Restore command to disable GARP |
CSCvb94697 |
2800/3800 11n macbook client has dropping connectivity while connecting to AP3800 |
CSCvb95147 |
AP 1572EAC unable to use 80MHz |
CSCvc00358 |
WLC crash "apfRogueTask_0" missed software watchdog |
CSCvc09824 |
the AP2800 band select stats counter show zero |
CSCvc13175 |
GLC-T SFP stopped working in CT5520 (1G Port down on 5520) |
CSCvc15149 |
Barbados 8.2 MR4 - Not beaconing a SSID when it is in an AP group and SSID enabled later |
CSCvc16755 |
AP3802 custom power level not initialized after reboot |
CSCvc18699 |
Corsica: High pings drops traffic connectivity drops seen 8.2.131.40 |
CSCvc23658 |
Clients not removed from flexconnect and capwap in APs flexconnect central-sw |
CSCvc25669 |
rfidTask is causing a high CPU on the WLC |
CSCvc29030 |
100MHz channel separation between 5G band with XOR in monitor mode |
CSCvc31133 |
Unable to enable wlan with enabled selected option in GUI. Security: FT + Open |
CSCvc31304 |
83MR1: AP syslog flood for TLV-DEC-ERR: cannot process TLV for TLV_DMS_CLIENT_REQUEST_PAYLOAD(325/0) |
CSCvc32706 |
3800 APs: Not seeing all COS neighbors |
CSCvc32856 |
Barbados: Sends a AQ Event as soon as RRM changes channel causing bad channel selection and changes |
CSCvc33258 |
WLC: Unable to config RX-SOP threshold for IW3702 AP |
CSCvc33511 |
SNMPv3 access failing with either unknown user / no response |
CSCvc38214 |
2800/3800 Sending Acks to client at 54 data rate although Basic rate is 12 & 24 |
CSCvc39963 |
Barbados : FRA revert command failing to revert XOR to 2.4GHz |
CSCvc40470 |
AP radio hang chatter: wl0: rxRingStuckDetect(271): RX-HANG Detected!! |
CSCvc40564 |
TPC - Maximum/Minimum power level are not set as expected |
CSCvc42566 |
1702I AP - radio resets observed due to CleanAir error count exceeded |
CSCvc42741 |
AP3800/AP2800 : Failed to receive data keepalive and Process capwapd gone |
CSCvc42939 |
3800 AP duplicating multicast packets |
CSCvc43232 |
2800/3800 uses 11n data rates to send data packets to 11b only clients failing to assoc |
CSCvc43328 |
2800/3800 Sending Acks to client at 54 data rate although Basic rate is 12 & 24 in 8.2Mr4Esc |
CSCvc45038 |
2800/3800 Beacon drift 25ms with offchannel/cleanair scanning @3sec mc9060 client drops |
CSCvc48232 |
AP crash due to kernel panic at mhsm_transition |
CSCvc50228 |
2800/3800 Sending Data packets to the 11g clients sometimes with messed up data rates |
CSCvc50377 |
WLC7500: emWeb crash while doing "show run-config" on 8.0.110.11 |
CSCvc53578 |
2800/3800 11b only clients does not associate if HT is disabled |
CSCvc53675 |
1852 AP - kernel backtrace at ol_ath_tx_mgmt_wmi_send+0x0/0x1e4 |
CSCvc74695 |
XOR radio pushes local-mode AP config for flex-mode AP causing Client disconnect |
03-16-2017 02:22 PM
SYS light was flashing, console unresponsive, power cycle appears to have resolved it. APs downloading now.
03-31-2017 07:26 AM
Not exactly the same as you, but similar enough to mention.
I had an issue with 8.1.131 (I think that version) where pre-downloading software to the APs left the controller unresponsive. We have around 2000 APs. I couldn't SSH into it and the console didn't even respond. SNMP still worked as did syslog. Regular Wi-Fi traffic was unaffected. Everything returned to normal once pre-download finished.
We noticed the issue because Prime reported that both of the WLC power supplies had failed, which was obviously bogus.
Weirdness.
03-30-2017 11:17 AM
Are there any reasons 8.2.151 not to be the suggested image for WLC 5520 but to be for the others?
03-31-2017 01:29 AM
Hi
No reason, it was a minor error on the suggestion rule, I just updated it , thanks for reporting
regards
04-05-2017 11:46 PM
Hello Javier,
yesterday a security advisory was released regarding WME DoS vulnerability (CSCva86353)
There is however no explicit statement, if 8.2.151.0 is vulnerable or not. We are currently planning to roll out this image to our WLCs and would need a confirmation, if this vulnerability affects this release or not.
Best Regards,
Patrick
04-06-2017 12:09 AM
Hi Patrick
it is explicitly mentioned on the advisory and on the bug release notes, that version 8.2.130.0 and higher are fixed, thus 140, 150.0, etc. and anything after are not affected
regards
05-20-2017 06:36 AM
Hello, do the 8.2.151.0 code was the last from this train? Are there going to be more releses from 8.2 or we should focus on 8.3/4 ?
My concern is 1/2/3800 APs.
05-20-2017 11:27 AM
Hello
we plan to do an additional 82MR6 for July timeframe, the interim code is already available here:
https://supportforums.cisco.com/discussion/13284941/82mr6-interim-release-availability
you can request access
This is the last planned release for 8.2 train, from that point, we will focus on 8.3 moving forward as next MD long life rlease
Regards
07-31-2017 11:56 AM
8.2.160.0(ED) is out for some days. :)
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide