cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
793
Views
0
Helpful
8
Replies
Highlighted
Beginner

802.11n 5@40

I try get all benefits of 802.11n with 1262N in standalone mode (12.4(25d)JA)

But I see the next

Settings for int dot11radio1 is the next

speed  basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.

channel width 40-above

channel 5300

station-role root

All antennas are active, wmm is active

But I get only about 2MB/s by ftp

For test I use the next scheme

Client-Win7(Linksys ae2500)(vlanA) == R1:1262N:Gi0  == Gi:SW:Gi == Gi:(vlanA):FtpServer

On the same stand I get about 6MB/s with 5Ghz and channel width 20MHz

In all attempts was only one client and the clean environment, i proved it with a spectrum-analyzer

Tell me what I'm doing wrong? Thank you.

Client associated with next parameters:

5@40:

----

Key Mgmt type    : WPAv2 PSK         

Encryption       : AES-CCMP

Current Rate     : m15.              

Capability       : WMM 11h

Supported Rates  : 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15

Bandwidth        : 40 MHz 

5@20

---

And the same, but bandwidth  is   20 MHz

8 REPLIES 8
Highlighted
Hall of Fame Master

Eugene,

What is your baseline with a wired pc doing the same test on vlan A?

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Highlighted

The supported rates is not important. Those are for a/b/g. What you have to verify is if High Throughput(HT) is enabled with the MCS rates 0-7 for clients and 8-15 for AP.

Highlighted

Scott,

with a wired pc I get 20-25MB/s

ftp:gi - sw - gi:notebook and ftp:gi - gi:notebook

Highlighted

Have you tried different client for testing?

This link could be helpful:  http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080a3443f.shtml#topic8

HTH

Amjad

Rating useful replies is more useful than saying "Thank you"
Highlighted

Eugene,

What guard interval is set, 400ns or 800ns or only 800ns? 400ns ensures higher throughput than 800ns.

To be sure, enter the command

interface dot11radio 1 --------- 5GHz n radio

guard interval any

Highlighted

"guard interval any"     is default setting

sh controllers dot11Radio 1 | i Guard

Guard-Interval: Any

In any case, I attach the full version of sh controll dot11radio1

Maybe this is  will help to understand what I am missing

Highlighted

Сolleagues, the problem with the adapter.

Dlink dwa-160 rev A2 managed to get about 11MB/s

AE2500 is still not working as it should be.

Surprised that Linksys is such a bad product.

May be possible to configure the adapter,

but after all that time that I spent I very doubt.

Thanks all for replies

Highlighted

Eugene,

It is always a good idea to baseline from the wired side, so you can get an idea of the actual throughput from the devices you are using, and you can figure out the percentage of actual throughput if the ftp was connected to a 100mbps or 1000mbps connection.  Using multiple adapter as a test is also good, because each one has it good and bad.  At least you were able to see that in your testing.

-Scott
*** Please rate helpful posts ***