cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2270
Views
5
Helpful
2
Replies

AIR CAP 3602E-E-K9 NEW AUTONOMOUS IOS CAN,T LOAD PROPERLY DEVICE IS NOW IN AP MODE

RASHID ASGHAR
Beginner
Beginner

ap: boot

Loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"...flash:/ap3g2-

k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1: no such file or directory

Error loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"

Interrupt within 5 seconds to abort boot process.

Loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1"...#############

##############

File "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1" uncompressed and i

nstalled, entry point: 0x2003000

executing...

Secondary Bootloader - Starting system.

Xmodem file system is available.

ap: boot

Loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"...flash:/ap3g2-

k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1: no such file or directory

Error loading "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"

Interrupt within 5 seconds to abort boot process.

Unable to locate IOS image with name **xx**.

Boot CMD: 'flash:/ap3g2-k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1'

Loading "flash:/ap3g2-k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1"...flash:/ap3g2-

k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1: no such file or directory

Error loading "flash:/ap3g2-k9w7-xx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1"

Interrupt within 5 seconds to abort boot process.

Boot process failed...

ap:

ap:

ap:

DEVICE IS NOW IN AP MODE  HOW CAN I EASILY LOAD ANOTHER IOS............................TELL ME SOME AP MODE COMMANDS

2 Replies 2

Please goes a long way matey :-).

The experts can probably correct me here but it looks like your IOS is in  "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1" and your AP is trying to boot from: "flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-xx.152-4.JA1"

So firstly, try using the following command:

set boot flash:/ap3g2-k9w7-mx.152-4.JA1/ap3g2-k9w7-mx.152-4.JA1

then issue the 'boot' command and see if that works.

If not, grab a copy of your IOS and setup a TFTP server connected to your Access Point. You may need to turn off your personal firewall when you do this.

Follow the instructions at this link which explain it on an 1142 which should be the same method:

https://supportforums.cisco.com/docs/DOC-14636

Let us know how you go!

Thank you Richard, that worked perfectly for me.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers