cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
996
Views
15
Helpful
9
Replies

AIR-CAP2702I-R-K9 Flex AP connected switch interface down Frequently

Hi,

 

AIR-CAP2702I-R-K9 (Russia) this is the AP which is connected on the flex wireless controller (Germany), at last 3 months we are having issue that the AP connected switch interface Down frequently. As part of our troubleshooting I have replaced the Switch interface and cables, POE adapter and AP as well but still the issue not fixed. In the same setup we have some other locations as well but, there is no problem on there i.e. the issue only for this location 

 

As part of troubleshooting I've observed the interface down issue only on if clients connected to the AP. If there is no client connected on this AP the interface will not down So, please someone advise me to fix the issue 

 

Thanks in advance!

 

Suriya

9 Replies 9

saravlak
Spotlight
Spotlight

are Country code Russia enabled on WLC.

are the gig interface flapping or just go down straight.

any logs from AP and switch sides showing the reason for it down.

Hi Saravlak

 

There is no logs from switch side apart from that AP connected interface fluctuation log. And i forget to add one more point which is whenever the interface went down at that time i found that the AP also rebooted 

 

So, i believe that due to the AP rebooted issue, interface getting fluctuation........And i could not's see any issue related logs from Ap since the AP uptime is new and i don't see any rebooted reason as well 

 

FYI.... Last 3 days there was no fluctuation and the current AP uptime is 3 day's, the reason which i believe the was no client connected on that AP. So, what i am trying to say, if some clients will be connected to AP, then only the issue will occur i.e. AP will reboot 

check/reproduce, if the AP is crashing or going on silent reboot whenever client trying to connect.

if its remote then try replacing that unit and check.

Scott Fella
Hall of Fame
Hall of Fame

There is one thing to keep in mind.  Russia doesn't allow DTLS and typically you would have a controller specific for Russia as the code is also different, you would use the LDPE image for that.

Solved: Flexconnect russia DTLS - Cisco Community

-Scott
*** Please rate helpful posts ***

And if the AP is crashing (sounds like it) then that is a software bug.  You didn't mention what version of code you're running?

There should be crash files on the AP and you should see logs on the WLC: Management -> Tech Support -> AP Crash Log

TAC can decode the crash file to identify known or new bug.  If you're running old code then update to latest and it may solve the problem for you.

Hi Scott,

 

Please find the AP crash log and version details and kindly let me know if you found something 

 

Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JA12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Fri 20-Oct-17 20:51 by prod_rel_team

ROM: Bootstrap program is C2700 boot loader
BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)

AP70df.2f42.625c uptime is 26 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-xx.153-3.JA12"
Last reload reason:

 

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP2702I-R-K9 (PowerPC) processor (revision A0) with 376814K/134656K bytes of memory.
Processor board ID JTV2142A0ZU
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.152.0
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 70:DF:2F:42:62:5C
Part Number : 73-15824-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC212461P4
Top Assembly Part Number : 068-100335-03
Top Assembly Serial Number : JTV2142A0ZU
Top Revision Number : A0
Product/Model Number : AIR-CAP2702I-R-K9

 

Configuration register is 0xF

 

 

has joined controller wlcdemchflex01
*May 11 15:55:54.935: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*May 11 15:55:54.951: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*May 11 15:55:54.951: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*May 11 15:55:54.951: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
*May 11 15:55:54.951: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration fileWLAN id 1, SSID stwianl2, L2ACL , L2ACL AP
WLAN id 4, SSID lguest, L2ACL , L2ACL AP
WLAN id 5, SSID lmobile, L2ACL , L2ACL AP

*May 11 15:55:55.135: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
CMD: 'interface Dot11Radio0.1' 15:55:55 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:55 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:55 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:55 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021capwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config

CMD: 'interface Dot11Radio0.1' 15:55:55 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:55 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:55 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:55 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:55 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'dot11 ssid "stwianl2"' 15:55:55 UTC Tue May 11 2021
CMD: 'no mcuc enable' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'dot11 ssid "stwianl2"' 15:55:55 UTC Tue May 11 2021
CMD: 'no passive-client enable' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:55 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:55 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:55 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:55 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:55 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:55 UTC Tue May 11 2021
CMD: 'commands ssid-global include passive-client enable' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:55 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:55 UTC Tue May 11 2021
CMD: 'commands ssid-global include mcuc enable' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
CMD: 'no parser view TLV_WLAN_FEAT_STATUS' 15:55:55 UTC Tue May 11 2021
CMD: 'end' 15:55:55 UTC Tue May 11 2021
*May 11 15:55:55.735: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*May 11 15:55:55.951: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*May 11 15:55:55.975: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*May 11 15:55:55.983: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*May 11 15:55:55.991: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
CMD: 'dot11 ssid "lguest"' 15:55:56 UTC Tue May 11 2021
CMD: 'no mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lguest"' 15:55:56 UTC Tue May 11 2021
CMD: 'no passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:56 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'no parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lmobile"' 15:55:56 UTC Tue May 11 2021
CMD: 'no mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lmobile"' 15:55:56 UTC Tue May 11 2021
CMD: 'no passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:56 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'no parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "stwianl2"' 15:55:56 UTC Tue May 11 2021
CMD: 'no mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "stwianl2"' 15:55:56 UTC Tue May 11 2021
CMD: 'no passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:56 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'no parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lguest"' 15:55:56 UTC Tue May 11 2021
CMD: 'no mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lguest"' 15:55:56 UTC Tue May 11 2021
CMD: 'no passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:56 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'no parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lmobile"' 15:55:56 UTC Tue May 11 2021
CMD: 'no mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'dot11 ssid "lmobile"' 15:55:56 UTC Tue May 11 2021
CMD: 'no passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:56 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include passive-client enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:55:56 UTC Tue May 11 2021
CMD: 'commands ssid-global include mcuc enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'no parser view TLV_WLAN_FEAT_STATUS' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0.800' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 800 native' 15:55:56 UTC Tue May 11 2021
CMD: ' bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0.800' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 800 native' 15:55:56 UTC Tue May 11 2021
CMD: ' bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0.800' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 800 native' 15:55:56 UTC Tue May 11 2021
CMD: ' bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0.80' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 80' 15:55:56 UTC Tue May 11 2021
CMD: ' bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio0.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'no bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'no cdp enable' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1.1' 15:55:56 UTC Tue May 11 2021
CMD: 'bridge-group 4' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
CMD: 'line vty 0 15' 15:55:56 UTC Tue May 11 2021
CMD: ' transport input ssh' 15:55:56 UTC Tue May 11 2021
CMD: 'exit' 15:55:56 UTC Tue May 11 2021
CMD: 'end' 15:55:56 UTC Tue May 11 2021
*May 11 15:55:57.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*May 11 15:55:57.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*May 11 15:55:57.479: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*May 11 15:55:57.491: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*May 11 15:55:57.499: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
CMD: 'no username osram' 15:55:57 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'end' 15:55:57 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: PASSWORD statement not printed
CMD: 'end' 15:55:57 UTC Tue May 11 2021
*May 11 15:55:58.111: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
CMD: 'aaa new-model ' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'aaa authentication dot1x reap_eap_methods group radius' 15:55:58 UTC Tue May 11 2021
CMD: 'aaa authentication suppress null-username' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap profile lwapp_eap_profile' 15:55:58 UTC Tue May 11 2021
CMD: 'no method fast' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap profile lwapp_eap_profile' 15:55:58 UTC Tue May 11 2021
CMD: 'no method leap' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap profile lwapp_eap_profile' 15:55:58 UTC Tue May 11 2021
CMD: 'no method tls' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap profile lwapp_eap_profile' 15:55:58 UTC Tue May 11 2021
CMD: 'no pki-trustpoint' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap profile lwapp_eap_profile' 15:55:58 UTC Tue May 11 2021
CMD: 'no method peap' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap method fast profile reap_method_fast' 15:55:58 UTC Tue May 11 2021
CMD: 'no authority-id identity' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap method fast profile reap_method_fast' 15:55:58 UTC Tue May 11 2021
CMD: 'no authority-id information' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap method fast profile reap_method_fast' 15:55:58 UTC Tue May 11 2021
CMD: 'no local-key' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap method fast profile reap_method_fast' 15:55:58 UTC Tue May 11 2021
CMD: 'no pac-ttl' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'no eap method fast profile reap_method_fast' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
CMD: 'eap profile lwapp_eap_profile' 15:55:58 UTC Tue May 11 2021
CMD: 'method fast' 15:55:58 UTC Tue May 11 2021
CMD: 'end' 15:55:58 UTC Tue May 11 2021
*May 11 15:55:58.479: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*May 11 15:55:58.491: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
CMD: PASSWORD statement not printed
CMD: 'end' 15:55:58 UTC Tue May 11 2021
*May 11 15:55:58.535: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*May 11 15:55:58.543: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*May 11 15:55:58.551: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
CMD: 'interface Dot11Radio0' 15:55:59 UTC Tue May 11 2021
CMD: 'station-role root' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'interface Dot11Radio1' 15:55:59 UTC Tue May 11 2021
CMD: 'station-role root' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0' 15:55:59 UTC Tue May 11 2021
CMD: 'no carrier-delay' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view STAMODE_FALLBACK' 15:55:59 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:59 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view STAMODE_FALLBACK' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view STAMODE_FALLBACK' 15:55:59 UTC Tue May 11 2021
CMD: 'commands interface include all station-role' 15:55:59 UTC Tue May 11 2021
CMD: 'commands interface include all carrier-delay' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include interface GigabitEthernet0' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view STAMODE_FALLBACK' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include interface Dot11Radio0' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include interface Dot11Radio1' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no parser view STAMODE_FALLBACK' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no capwap ap arp-cache' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view ARPCACHE' 15:55:59 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:59 UTC Tue May 11 2021
CMD: 'commands exec include show running-config' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view ARPCACHE' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view ARPCACHE' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all capwap ap arp-cache' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no parser view ARPCACHE' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'dot11 flex mcuc range clear' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view MC2UC_CFG' 15:55:59 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:55:59 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view MC2UC_CFG' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'parser view MC2UC_CFG' 15:55:59 UTC Tue May 11 2021
CMD: 'commands configure include dot11 flex mcuc range' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no parser view MC2UC_CFG' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
*May 11 15:55:59.535: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*May 11 15:55:59.543: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*May 11 15:55:59.575: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
CMD: 'aaa authentication dot1x reap_eap_methods group radius' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no aaa authorization credential-download reap_eap_methods local' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no aaa local authentication reap_eap_methods authorization reap_eap_methods' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no aaa authorization network reap_eap_methods local' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'aaa authentication dot1x reap_eap_methods group radius' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no aaa authorization credential-download reap_eap_methods local' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no aaa local authentication reap_eap_methods authorization reap_eap_methods' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'no aaa authorization network reap_eap_methods local' 15:55:59 UTC Tue May 11 2021
CMD: 'end' 15:55:59 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0' 15:56:00 UTC Tue May 11 2021
CMD: 'no bridge-group 1' 15:56:00 UTC Tue May 11 2021
CMD: 'end' 15:56:00 UTC Tue May 11 2021
CMD: 'interface GigabitEthernet0.800' 15:56:00 UTC Tue May 11 2021
CMD: 'encapsulation dot1Q 800 native' 15:56:00 UTC Tue May 11 2021
CMD: ' bridge-group 1' 15:56:00 UTC Tue May 11 2021
CMD: 'cdp enable' 15:56:00 UTC Tue May 11 2021
CMD: 'end' 15:56:00 UTC Tue May 11 2021
CMD: 'parser view L2_ACL_MAP' 15:56:00 UTC Tue May 11 2021
CMD: PASSWORD statement not printed
CMD: 'commands exec include configure terminal' 15:56:00 UTC Tue May 11 2021
CMD: 'commands exec include all show' 15:56:00 UTC Tue May 11 2021
CMD: 'end' 15:56:00 UTC Tue May 11 2021
CMD: 'parser view L2_ACL_MAP' 15:56:00 UTC Tue May 11 2021
CMD: 'commands configure include all exit' 15:56:00 UTC Tue May 11 2021
CMD: 'commands configure include all end' 15:56:00 UTC Tue May 11 2021
CMD: 'end' 15:56:00 UTC Tue May 11 2021
CMD: 'parser view L2_ACL_MAP' 15:56:00 UTC Tue May 11 2021
CMD: 'commands configure include dot11 ssid' 15:56:00 UTC Tue May 11 2021
CMD: 'commands ssid-global include mac access-group' 15:56:00 UTC Tue May 11 2021
CMD: 'end' 15:56:00 UTC Tue May 11 2021
CMD: 'no parser view L2_ACL_MAP' 15:56:00 UTC Tue May 11 2021
CMD: 'end' 15:56:00 UTC Tue May 11 2021
*May 11 15:56:00.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*May 11 15:56:17.735: %CLEANAIR-6-STATE: Slot 1 enabled
*May 11 15:56:29.511: %CLEANAIR-6-STATE: Slot 0 enabled
*May 11 16:05:27.975: %DOT11-4-FLUSH_DEAUTH: Consecutive tx fail 500+: deauth cc2f.7170.c975
*May 12 01:46:09.635: %DOT11-4-FLUSH_DEAUTH: Consecutive tx fail 500+: deauth 34f3.9a86.5f6f
*May 12 05:10:08.531: %SYS-3-MGDTIMER: Previous timer has bad forward linkage, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF8D0z 1C06850z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:10:10.543: %SYS-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (7/4),process = LWAPP CLIENT.
-Traceback= 0x1C063ECz 0x1C06990z 0x1C06058z 0x133EF4Cz 0x1325CDCz
*May 12 05:10:18.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:10:18.567: %SYS-3-CPUHOG: Task is running for (10000)msecs, more than (2000)msecs (13/4),process = LWAPP CLIENT.
-Traceback= 0x1324A98z 0x2AFFF14z 0x1C063DCz 0x1C06990z 0x1C06058z 0x133EF4Cz 0x1325CDCz
*May 12 05:10:28.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:10:38.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:10:48.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:10:58.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:11:08.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:11:10.783: %SYS-3-CPUHOG: Task is running for (62000)msecs, more than (2000)msecs (67/4),process = LWAPP CLIENT.
-Traceback= 0x2AFFAA4z 0x2AFFF44z 0x1C063DCz 0x1C06990z 0x1C06058z 0x133EF4Cz 0x1325CDCz
*May 12 05:11:18.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:11:28.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:11:36.891: %SYS-3-CPUHOG: Task is running for (88000)msecs, more than (2000)msecs (94/4),process = LWAPP CLIENT.
-Traceback= 0x1266AF8z 0x1C06844z 0x1C06058z 0x133EF4Cz 0x1325CDCz
*May 12 05:11:38.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:11:46.943: %SYS-3-CPUHOG: Task is running for (98000)msecs, more than (2000)msecs (107/4),process = LWAPP CLIENT.
-Traceback= 0x1455E78z 0x1BCFBDCz 0x1BBB830z 0x1C06978z 0x1C06058z 0x133EF4Cz 0x1325CDCz
*May 12 05:11:48.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:11:58.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz
*May 12 05:12:08.531: %SYS-3-MGDTIMER: NZ prev pointer but not running, timer = 4677868. -Process= "LWAPP CLIENT", ipl= 6, pid= 82
-Traceback= 11AEF60z 2AFF40Cz 2AFFF44z 1C063DCz 1C06990z 1C06058z 133EF4Cz 1325CDCz

05:12:26 UTC Wed May 12 2021: Unexpected exception to CPU: vector 700, PC = 0x133DADC , LR = 0x133DADC

-Traceback= 0x133DADCz

CPU Register Context:
MSR = 0x00029200 CR = 0x24248042 CTR = 0x01F3911C XER = 0x00000000
R0 = 0x0133DADC R1 = 0x06D83F94 R2 = 0x00010001 R3 = 0x04ADFC44
R4 = 0x00000000 R5 = 0x06D83C6C R6 = 0x00000000 R7 = 0x03C00000
R8 = 0x00029200 R9 = 0x00000000 R10 = 0x03C00000 R11 = 0x03C00000
R12 = 0x24248044 R13 = 0x41209502 R14 = 0x01C05C74 R15 = 0x045B7B10
R16 = 0x045B7A70 R17 = 0x045B7A98 R18 = 0x045B7FA0 R19 = 0x04677868
R20 = 0x0466BC10 R21 = 0x06D84070 R22 = 0x011A3C58 R23 = 0x0335A294
R24 = 0x06D8407C R25 = 0x06D84084 R26 = 0x00000006 R27 = 0x037B27A0
R28 = 0x00000000 R29 = 0x037BA718 R30 = 0x037B3E44 R31 = 0x00000000

TEXT_START : 0x01003000
DATA_START : 0x03000000
MCSRR0: 0x00000000, MCSRR1: 0x00000000 MCSR: 0x00000000 MCAR: 0x00000000

Total PCI 0 MC Error = 0; PCI LD count=0
Total PCI 1 MC Error = 0; PCI LD count=0
Total PCI 2 MC Error = 0; PCI LD count=0

=== Start of Crashinfo Collection (05:12:26 UTC Wed May 12 2021) ===

For image:
Cisco IOS Software, C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JA12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Fri 20-Oct-17 20:51 by prod_rel_team


System image file is: flash:/ap3g2-k9w8-mx.153-3.JA12/ap3g2-k9w8-xx.153-3.JA12

 

========= Show Alignment =============================


No alignment data has been recorded.

No spurious memory references have been recorded.

========== Stack Trace========

-Traceback= 0x133DADCz

========= Context ======================

C2700 Software (AP3G2-K9W8-M), Version 15.3(3)JA12, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 20-Oct-17 20:51 by prod_rel_team
Signal = 23, Vector = 700

MSR: 0x00021200 SRR0 = 0x0145B538 SRR1 = 0x00021200 DEAR = 0x00000000

CPU Register Context:
PC = 0x0133DADC MSR = 0x00029200 CR = 0x24248042 LR = 0x0133DADC
CTR = 0x01F3911C XER = 0x00000000 DAR = 0x00000000 DSISR = 0x400F0000
DEC = 0x00000000 TBU = 0x000001BE TBL = 0x237A4721 IMMR = 0x00000000
R0 = 0x0133DADC R1 = 0x06D83F94 R2 = 0x00010001 R3 = 0x04ADFC44
R4 = 0x00000000 R5 = 0x06D83C6C R6 = 0x00000000 R7 = 0x03C00000
R8 = 0x00029200 R9 = 0x00000000 R10 = 0x03C00000 R11 = 0x03C00000
R12 = 0x24248044 R13 = 0x41209502 R14 = 0x01C05C74 R15 = 0x045B7B10
R16 = 0x045B7A70 R17 = 0x045B7A98 R18 = 0x045B7FA0 R19 = 0x04677868
R20 = 0x0466BC10 R21 = 0x06D84070 R22 = 0x011A3C58 R23 = 0x0335A294
R24 = 0x06D8407C R25 = 0x06D84084 R26 = 0x00000006 R27 = 0x037B27A0
R28 = 0x00000000 R29 = 0x037BA718 R30 = 0x037B3E44 R31 = 0x00000000
========= Stack Dump ==========================

Stack Frame Pointer in Context is 0x6D83F94 , intstacks corrupted
: INVALID STACK ADDRESS

========= Process Level Info ==================
Regs R14-R31, CR, PC, MSR at last suspend; R3 from proc creation, PC unused:
R3 : 00000000 R14: 01C05C74 R15: 00000000 R16: 00000000 R17: 00000000
R18: 00000000 R19: 00000000 R20: 00000000 R21: 00000000 R22: 00000000
R23: 06D843F0 R24: 044D0000 R25: 044D0000 R26: 04649B10 R27: 03EDC8B8
R28: 06D843EC R29: 06D847C8 R30: 00000000 R31: 037C0000 CR: 24000022
PC : 012C9434 MSR: 00029200

========= Interrupt Level Stack Dump ==========

---- Level 1 Interrupt stack (base 0x0, size 0x0) is invalid ----

---- Level 2 Interrupt stack (base 0x0, size 0x0) is invalid ----

---- Level 3 Interrupt stack (base 0x0, size 0x0) is invalid ----

---- Level 4 Interrupt stack (base 0x0, size 0x2328) is invalid ----

---- Level 5 Interrupt stack (base 0x0, size 0x2328) is invalid ----

---- Level 6 Interrupt stack (base 0x0, size 0x2328) is invalid ----

---- Level 7 Interrupt stack (base 0x0, size 0x2328) is invalid ----

---- Level 8 Interrupt stack (base 0x0, size 0x0) is invalid ----

---- Level 9 Interrupt stack (base 0x0, size 0x0) is invalid ----

========= Register Memory Dump ================

Reg00(PC 133DADC [Not RAM Addr]
Reg01(MSR): 29200 [Not RAM Addr]
Reg02(CR 24248042 [Not RAM Addr]
Reg03(LR 133DADC [Not RAM Addr]
Reg04(CTR): 1F3911C [Not RAM Addr]
Reg05(XER): 0 [Not RAM Addr]
Reg06(DAR): 0 [Not RAM Addr]
Reg07(DSISR): 400F0000 [Not RAM Addr]
Reg08(DEC): 0 [Not RAM Addr]
Reg09(TBU): 1BE [Not RAM Addr]
Reg10(TBL): 237A4721 [Not RAM Addr]
Reg11(IMMR): 0 [Not RAM Addr]
Reg12(R0 133DADC [Not RAM Addr]
Reg13(R1 6D83F94 [Not RAM Addr]
Reg14(R2 10001 [Not RAM Addr]
Reg15(R3 4ADFC44 [Not RAM Addr]
Reg16(R4 0 [Not RAM Addr]
Reg17(R5 6D83C6C [Not RAM Addr]
Reg18(R6 0 [Not RAM Addr]
Reg19(R7 3C00000 [Not RAM Addr]
Reg20(R8 29200 [Not RAM Addr]
Reg21(R9 0 [Not RAM Addr]
Reg22(R10): 3C00000 [Not RAM Addr]
Reg23(R11): 3C00000 [Not RAM Addr]
Reg24(R12): 24248044 [Not RAM Addr]
Reg25(R13): 41209502 [Not RAM Addr]
Reg26(R14): 1C05C74 [Not RAM Addr]
Reg27(R15): 45B7B10 [Not RAM Addr]
Reg28(R16): 45B7A70 [Not RAM Addr]
Reg29(R17): 45B7A98 [Not RAM Addr]
Reg30(R18): 45B7FA0 [Not RAM Addr]
Reg31(R19): 4677868 [Not RAM Addr]
Reg32(R20): 466BC10 [Not RAM Addr]
Reg33(R21): 6D84070 [Not RAM Addr]
Reg34(R22): 11A3C58 [Not RAM Addr]
Reg35(R23): 335A294 [Not RAM Addr]
Reg36(R24): 6D8407C [Not RAM Addr]
Reg37(R25): 6D84084 [Not RAM Addr]
Reg38(R26): 6 [Not RAM Addr]
Reg39(R27): 37B27A0 [Not RAM Addr]
Reg40(R28): 0 [Not RAM Addr]
Reg41(R29): 37BA718 [Not RAM Addr]
Reg42(R30): 37B3E44 [Not RAM Addr]
Reg43(R31): 0 [Not RAM Addr]


========= End of Crashinfo Collection ================

------------------ show chunk failures ------------------


When Cause Caller In-use Chunk Name
00:00:02 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:01 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:01 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:01 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:01 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:00 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:00 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:00 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:00 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg
00:00:00 3 0x1B41340 255 0x6D39C0C CAPWAP dot11 mg


***** End of Crash File dump *****

Time to open TAC case with the AP crash logs, core dump. if possible, upgrade to latest supported stable software and give it a try.

Ok thanks, let me check with TAC

That release on the AP sounds like WLC code 8.0.152.0. You might not get much support for that, because that release is EoL since several years now.

If you don't have any legacy APs, you might want to try upgrading to the latest 8.5.x or at least (if it's an 5508 WLC) to 8.3.150.x TAC escalation build. 

Code compatibility matrix: https://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card