10-09-2012 01:22 PM - edited 07-03-2021 10:47 PM
Hi,
hope you are all doing well,
i need your advice that i have a AIR-LAP1131AG-A-K9 V05 Not able to join WLC 4402 with error,
I connect the console to the LAP1131 and i found the below error log,
thanks in advanced for your effort,
##############################################################################################################################################################################################################################
File "flash:/c1130-k9w8-mx.124-21a.JA/c1130-k9w8-mx.124-21a.JA" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(21a)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 08-Jun-09 16:10 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 25 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 6821888
flashfs[1]: Bytes available: 9177088
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio0 present A506 7100 E8000000 A0000000 80000000 3
Radio1 present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1421N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 6.0.182.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 54:75:D0:16:44:FE
Part Number : 73-8962-14
PCA Assembly Number : 800-24818-13
PCA Revision Number : A0
PCB Serial Number : FOC141707J5
Top Assembly Part Number : 800-29144-03
Top Assembly Serial Number : FTX1421N00D
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-A-K9
% Please define a domain-name first.
Press RETURN to get started!
p: 10.100.1.250 peer_port: 5246
*Oct 2 15:20:48.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 2 15:20:49.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:20:49.412: %CAPWAP-5-SENDJOIN: sending Join Request to 10.100.1.250
*Oct 2 15:20:49.413: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 2 15:20:49.504: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 2 15:20:49.504: %CAPWAP-3-ERRORLOG: Starting config timer
*Oct 2 15:20:49.512: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.100.1.250
*Oct 2 15:20:49.512: %DTLS-5-PEER_DISCONNECT: Peer 10.100.1.250 has closed connection.
*Oct 2 15:20:49.512: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.100.1.250:5246
*Oct 2 15:20:49.556: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:20:49.556: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:20:49.566: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 2 15:20:49.578: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:20:49.578: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:20:49.610: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:20:49.638: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:20:49.639: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 2 15:20:49.671: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:20:59.593: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 2 15:20:59.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:20:59.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 2 15:21:00.413: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:00.415: %CAPWAP-5-SENDJOIN: sending Join Request to 10.100.1.250
*Oct 2 15:21:00.415: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 2 15:21:00.505: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 2 15:21:00.505: %CAPWAP-3-ERRORLOG: Starting config timer
*Oct 2 15:21:00.516: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.100.1.250
*Oct 2 15:21:00.517: %DTLS-5-PEER_DISCONNECT: Peer 10.100.1.250 has closed connection.
*Oct 2 15:21:00.517: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.100.1.250:5246
*Oct 2 15:21:00.562: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:00.562: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:00.573: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 2 15:21:00.585: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:00.585: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:21:00.617: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:00.645: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:21:00.676: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:10.600: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 2 15:21:11.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:11.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 2 15:21:12.404: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:12.406: %CAPWAP-5-SENDJOIN: sending Join Request to 10.100.1.250
*Oct 2 15:21:12.406: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 2 15:21:12.497: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 2 15:21:12.497: %CAPWAP-3-ERRORLOG: Starting config timer
*Oct 2 15:21:12.505: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.100.1.250
*Oct 2 15:21:12.505: %DTLS-5-PEER_DISCONNECT: Peer 10.100.1.250 has closed connection.
*Oct 2 15:21:12.506: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.100.1.250:5246
*Oct 2 15:21:13.174: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:13.175: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:13.184: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 2 15:21:13.184: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Oct 2 15:21:13.196: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:13.196: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:21:13.198: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 2 15:21:13.228: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:13.229: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Oct 2 15:21:13.257: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:21:13.258: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 2 15:21:13.259: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 2 15:21:13.289: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:23.212: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 2 15:21:23.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:23.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 2 15:21:24.410: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:24.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.100.1.250
*Oct 2 15:21:24.411: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 2 15:21:24.502: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 2 15:21:24.502: %CAPWAP-3-ERRORLOG: Starting config timer
*Oct 2 15:21:24.512: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.100.1.250
*Oct 2 15:21:24.512: %DTLS-5-PEER_DISCONNECT: Peer 10.100.1.250 has closed connection.
*Oct 2 15:21:24.512: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.100.1.250:5246
*Oct 2 15:21:24.557: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:24.557: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:24.567: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 2 15:21:24.579: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:24.579: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:21:24.611: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:24.639: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Oct 2 15:21:24.640: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 2 15:21:24.671: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 2 15:21:34.594: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 2 15:21:35.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:35.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 2 15:21:36.409: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.100.1.250 peer_port: 5246
*Oct 2 15:21:36.410: %CAPWAP-5-SENDJOIN: sending Join Request to 10.100.1.250
*Oct 2 15:21:36.410: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 2 15:21:36.503: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 2 15:21:36.504: %CAPWAP-3-ERRORLOG: Starting config timer
*Oct 2 15:21:36.514: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.100.1.250
*Oct 2 15:21:36.514: %DTLS-5-PEER_DISCONNECT: Peer 10.100.1.250 has closed connection.
*Oct 2 15:21:36.515: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.100.1.250:5246
*Oct 2 15:21:36.559: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:36.559: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 2 15:21:36.569: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 2 15:21:36.581: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Solved! Go to Solution.
10-11-2012 06:52 AM
Login to the WLC, go to Wireless > Country. Check the box for US.
HTH,
Steve
------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered
10-10-2012 02:15 AM
Check the license.
are they on the same subnet?
force the AP to join ""
AP#capwap ap ip address
AP#capwap ap ip default-gateway
AP#capwap ap controller ip address
is it happening with all AP's?
10-10-2012 03:13 AM
Dear Yehya,
many thanks for your reply
I will do this and reply to you,
10-10-2012 01:47 PM
Dear Yahya,
I will try the commands that you gave me then i will send you my feedback,
10-10-2012 02:35 PM
Ok so the working are -E and the -A are not able to join. Sounds like it would be a country code issue. Do you have US as an selected country code?
If your deployment is only in Europe you may just want to get your partner/reseller to get you -E instead.
Steve
Sent from Cisco Technical Support iPhone App
10-11-2012 03:00 AM
Hi Steve,
many thanks for the reply,
Is there any way to make it both -E and -A works on the WLC ?
10-11-2012 03:02 AM
Yes, add US as a country code.
Steve
Sent from Cisco Technical Support iPhone App
10-11-2012 06:23 AM
Hi Steve,
How can I do this?
please explain to me,
10-11-2012 06:52 AM
Login to the WLC, go to Wireless > Country. Check the box for US.
HTH,
Steve
------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered
10-14-2012 10:19 AM
If that do not help, did u bought him as lap or did u convert him from standalone to lap. If yes check if I allow self signed certificates under the security tab.
Sent from Cisco Technical Support iPhone App
10-15-2012 04:36 AM
Hi Steve,
many thanks for your reply i will try it and send you my feedback,
10-15-2012 04:39 AM
Hi Sebastain,
many thanks for your reply,
the device is originally coming as LAP with no changes made on it,
10-20-2012 01:28 PM
Many thanks all it's sovled now
it was as steve said it's Country issue,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide