cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
31825
Views
5
Helpful
30
Replies

AIR-LAP1242AG-A-K9 Cannot Join to WLC

arika_wahyono
Beginner
Beginner

Guys,

I have problem, i try to connect AP AIR-LAP1242AG-A-K9 to WLC 4400 with Software 7.0.98.218, but the AP indicator is blink and always request new IP addres (based on AP logg console), this device can ping from LAN but unstable (based on logg, the AP always request new IP Address).

anyone have any had same experience with this case?

This is log when i try console to AP.

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Xmodem file system is available.

flashfs[0]: 15 files, 4 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 15998976

flashfs[0]: Bytes used: 10084864

flashfs[0]: Bytes available: 5914112

flashfs[0]: flashfs fsck took 36 seconds.

Base ethernet MAC Address: 00:1d:45:36:86:ca

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1240-k9w8-mx.124-23c.JZ/c1240-k9w8-mx.124-23c.JZ"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1240-k9w8-mx.124-23c.JZ/c1240-k9w8-mx.124-23c.JZ" uncompressed and installed, entry point: 0x3000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 06-Apr-11 15:01 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

flashfs[1]: 15 files, 4 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15740928

flashfs[1]: Bytes used: 10084864

flashfs[1]: Bytes available: 5656064

flashfs[1]: flashfs fsck took 5 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

Radio0  present A506 7100 E8000000 A0000000 80000000 3

Radio1  present A506 6700 E8000100 A0040000 80010000 2

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 25590K/7168K bytes of memory.

Processor board ID FTX1135B3ZF

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

LWAPP image version 7.0.98.218

1 FastEthernet interface

2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: xxxxxxxxxx

Part Number                          : 73-9925-06

PCA Assembly Number                  : 800-26579-05

PCA Revision Number                  : xxxxx

PCB Serial Number                    : xxxxxxx

Top Assembly Part Number             : xxxxxxx

Top Assembly Serial Number           : xxxxxxx

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1242AG-A-K9 

% Please define a domain-name first.

Press RETURN to get started!

*Mar  1 00:00:06.526: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar  1 00:00:08.150: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0

*Mar  1 00:00:09.747: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1

*Mar  1 00:00:09.863: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar  1 00:00:09.895:  status of voice_diag_test from WLC is false

*Mar  1 00:00:12.004: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar  1 00:00:12.072: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 06-Apr-11 15:01 by prod_rel_team

*Mar  1 00:00:12.072: %SNMP-5-COLDSTART: SNMP agent on host AP001d.4536.86ca is undergoing a cold start

*Mar  1 00:00:12.154: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:00:12.161: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Mar  1 00:00:12.161: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar  1 00:00:12.369: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:00:13.016: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

*Mar  1 00:00:13.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

*Mar  1 00:00:13.170: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar  1 00:00:20.493: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

*Mar  1 00:00:30.976:  status of voice_diag_test from WLC is false

*Mar  1 00:00:31.083: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:00:34.263: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

*Mar  1 00:00:34.304: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up

*Mar  1 00:00:34.342: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up

*Mar  1 00:00:35.265: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up

*Mar  1 00:00:35.265: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated

*Mar  1 00:00:35.304: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar  1 00:00:42.131: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:00:42.135: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar  1 00:00:42.139: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar  1 00:01:32.143: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

*Mar  1 00:01:34.274: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source

Not in Bound state.

*Mar  1 00:01:40.659: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar  1 00:01:40.778: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar  1 00:01:48.652: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:01:48.655: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar  1 00:01:48.657: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar  1 00:02:28.661: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar  1 00:02:37.173: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar  1 00:02:37.290: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar  1 00:02:45.164: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:02:45.167: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar  1 00:02:45.169: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar  1 00:03:25.170: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar  1 00:03:33.681: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar  1 00:03:33.798: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar  1 00:03:41.673: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:03:41.676: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar  1 00:03:41.678: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar  1 00:04:21.679: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar  1 00:04:30.191: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar  1 00:04:30.308: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar  1 00:04:38.181: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:04:38.184: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar  1 00:04:38.187: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.tester.net

*Mar  1 00:05:18.191: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

*Mar  1 00:05:26.703: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.

*Mar  1 00:05:26.820: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.11.150, mask 255.255.255.0, hostname AP001d.xxxx.xxxx

Translating "CISCO-CAPWAP-CONTROLLER.tester.net"...domain server (10.10.10.40)

Translating "CISCO-LWAPP-CONTROLLER.tester.net"...domain server (10.10.10.40)

*Mar  1 00:05:34.694: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar  1 00:05:34.696: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.tester.net

*Mar  1 00:05:34.699: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROL

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Thanks!!!

30 Replies 30

Hi Sandeep,

So, what do you want me to do?

to change the timezone on WLC? i cant do that because will impact to network.

and with AP, that i know we cant change that, or do you have any idea to change the timezone on AP?

Thanks,

Arik

This shows that the AP has not been reset:

%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address x.x.x.x, mask 255.255.255.0, hostname TEST

You should see the default hostname of the AP which is AP

Thanks,

Scott

*****Help out other by using the rating system and marking answered questions as "Answered"*****

-Scott
*** Please rate helpful posts ***

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

Scott,

I think there is a firewall somewhere.

Hi Leo,

No firewall,

Thxs,

Arik

Hi Scott,

Before you said to factory default, i had been reset the AP, yes the hostname is the mac-address,

but to make sure i had to reset again and capture it,

this is the capture:

TEST#Xmodem file system is available.

flashfs[0]: 13 files, 4 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 15998976

flashfs[0]: Bytes used: 10060800

flashfs[0]: Bytes available: 5938176

flashfs[0]: flashfs fsck took 39 seconds.

Base ethernet MAC Address: 00:1d:45:36:86:ca

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

link auto-negotiating....

auto-negotiation takes 10000 milli-seconds to complete

ERROR: timeout waiting for auto-negotiation to complete

ERROR: fail to bring ethernet link up

The system has been encountered an error initializing

ethernet port. You may need to check hardware

The system is ignoring the error and continuing boot.

If you interrupt the system boot process, the following

commands will reinitialize ethernet, tftp, and finish

loading the operating system software:

    ether_init

    tftp_init

    boot

button is pressed, wait for button to be released...

button pressed for 173 seconds

process_config_recovery: set IP address and config to default 10.0.0.1

process_config_recovery: image recovery

ap:  delete flash:private-config

Are you sure you want to delete "flash:private-config" (y/n)?y

File "flash:private-config" not deleted -- no such file or directory

ap: delete flash:private-multiple-fs

Are you sure you want to delete "flash:private-multiple-fs" (y/n)?y

File "flash:private-multiple-fs" deleted

ap:

ap: boot

Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...##################################################################################################################################################################################################

File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000

executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Thu 30-Oct-08 12:05 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x003C24A0

Initializing flashfs...

flashfs[1]: 12 files, 4 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15998976

flashfs[1]: Bytes used: 10059776

flashfs[1]: Bytes available: 5939200

flashfs[1]: flashfs fsck took 4 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.

Processor board ID xxxxxF

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

LWAPP image version 3.0.51.0

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:1D:45:36:86:CA

Part Number                          : 73-9925-06

PCA Assembly Number                  : 800-26579-05

PCA Revision Number                  : A0

PCB Serial Number                    : xxxx

Top Assembly Part Number             : 800-29151-02

Top Assembly Serial Number           : xxxxx

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1242AG-A-K9 

The name for the keys will be: ap.cisco.com

% The key modulus size is 1024 bits

% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]

ip ssh version 2

    ^

% Invalid input detected at '^' marker.

transport input ssh

                 ^

% Invalid input detected at '^' marker.

aaa new-model

^

% Invalid input detected at '^' marker.

aaa authentication login default enable local none

^

% Invalid input detected at '^' marker.

o

^

% Invalid input detected at '^' marker.

Press RETURN to get started!

*Mar  1 00:00:08.205: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

*Mar  1 00:00:09.232: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down

*Mar  1 00:00:09.635: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source

*Mar  1 00:00:16.375: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Thu 30-Oct-08 12:05 by prod_rel_team

transport input ssh

                 ^

% Invalid input detected at '^' marker.

logging origin-id string AP:001d.4536.86ca

         ^

% Invalid input detected at '^' marker.

logging 255.255.255.255

        ^

% Invalid input detected at '^' marker.

logging trap 3

        ^

% Invalid input detected at '^' marker.

*Mar  1 00:00:27.393: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY

*Mar  1 00:00:27.882: Logging LWAPP message to 255.255.255.255.

TEST>

Thanks,

Arik

LWAPP image version 3.0.51.0

Hmmmm ... LWAPP.

Post the following output:

1.  sh ip int brief;

2.  sh inventory

If the AP can ping the 4404, the what happens if you enter this command "lwapp ap controller ip address "?

Product Version.................................. 7.0.98.218

RTOS Version..................................... 7.0.98.218

Bootloader Version............................... 4.0.206.0

And upgrade your firmware to 7.0.250.X.  Don't forget to upgrade the bootstrap too.

Dear Team,

My AP has associate with the wlc, all i do is reset and reset AP to factory default, and then i assign static ip address and now the AP has discover from wlc and then i change the static to dhcp and everything going normally.

this step has been done before but failed.

Thanks for support!!

Arik

this step has been done before but failed.

You mean this AP has joined a WLC before?  If so, then how come the AP is booting up the "RCV" file now?

Dear Leo,

I mean, i had reset the AP and assign static ip address before but still AP still cant associate to wlc.

and dont know why, this step is work now.

Thanks,

Arik

Ahhh ... Ok.  So problem solved?

yes Leo.

Sandeep Choudhary
VIP Mentor VIP Mentor
VIP Mentor

HI Arika,

First of all paste the output of these commands:

From WLC: sh sysinfo

From AP: sh version

*Mar  1 00:05:18.191: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

as per this error AP not able to find WLC. makse sure that atleast one method is avilable for AP to findout the AP, either broadcats or DHCP 43 option.

Regards

Dont forget to rate helpful posts

Naveen Kumar
Enthusiast
Enthusiast

So are you saying it works when you put a static address but not when you have the ap setup for dhcp?

Abha Jha
Cisco Employee
Cisco Employee

Try with the static IP as of the WLC management interface.

From this line:-

"

*Mar  1 00:05:18.191: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.

Not in Bound state.

"

it seems AP is not able to join WLC with the IP address it gets assigned from the DHCP.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: