cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
12285
Views
5
Helpful
23
Replies

AP 1142 cannot attach to 5508 WLC 7.4 (Invalid event 10 & state 5 combination)

david_mayor
Beginner
Beginner

Hello,

I am fighting to get an 1140 LAP attached to a 5508 WLC running code 7.4.110.0.

Here is what I get on the AP logs:

*Nov 12 08:39:00.106: %CAPWAP-3-ERRORLOG: Selected MWAR 'gvenwc0006'(index 0).
*Nov 12 08:39:00.106: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 12 08:39:01.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.71.142.7 peer_port: 5246
*Nov 12 08:39:01.889: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.71.142.7 peer_port: 5246
*Nov 12 08:39:01.890: %CAPWAP-5-SENDJOIN: sending Join Request to 10.71.142.7
*Nov 12 08:39:02.000: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Nov 12 08:39:02.000: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Nov 12 08:39:02.000: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Nov 12 08:39:02.000: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.71.142.7
*Nov 12 08:39:06.889: %CAPWAP-5-SENDJOIN: sending Join Request to 10.71.142.7
*Nov 12 08:40:00.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.71.142.7:5246
*Nov 12 08:40:01.053: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Nov 12 08:40:01.101: Starting Ethernet promiscuous mode
*Nov 12 08:40:11.107: %CAPWAP-3-ERRORLOG: Selected MWAR 'gvenwc0006'(index 0).
*Nov 12 08:40:11.107: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 12 08:40:11.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.71.142.7 peer_port: 5246
*Nov 12 08:40:11.885: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.71.142.7 peer_port: 5246
*Nov 12 08:40:11.886: %CAPWAP-5-SENDJOIN: sending Join Request to 10.71.142.7
*Nov 12 08:40:11.968: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Nov 12 08:40:11.968: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Nov 12 08:40:11.968: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Nov 12 08:40:11.968: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.71.142.7

I already tried to erase the lwap configuration of the AP, to reload it, etc. But no success.

Can anyone help me ?

Many thanks,

David

23 Replies 23

Rasika Nayanajith
VIP Mentor VIP Mentor
VIP Mentor

Post "show sysinfo" of your WLC & "show version" of your AP

Rasika

Hi Manannalage,

We are facing below issue. AP (AIR-LAP1131AG-A-K9) is not able to join controller 2504. Below is the console output.

NA-AA-AP1#ping NA-HQ-WLC-01
Translating "NA-HQ-WLC-01"...domain server (172.16.1.21)
% Unrecognized host or address, or protocol not running.

NA-AA-AP1#
*Mar  1 00:03:21.394: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
*Mar  1 00:03:21.425: Flex Non AP-Specific config version mismatch. Clearing it! Current Version 7.6.130.0, stored file version 8.0.110.11
*Mar  1 00:03:21.425: LWAPP REAP CFG is not valid, please connect to Controller once
*Mar  1 00:03:21.950: %LWAPP-4-CLIENTEVENTLOG: No REAP configuration file to load. Connect to controller to get configuration file
*Mar  1 00:03:21.951: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Mar  1 00:05:42.394: %CAPWAP-3-STATIC_TO_DHCP_IP: Could not discover WLC using static IP. Forcing AP to use DHCP.
*Mar  1 00:05:51.322: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar  1 00:05:51.322: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar  1 00:05:51.418: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 172.16.143.215, mask 255.255.255.0, hostname NA-AA-AP1

*Mar  1 00:05:51.418: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
Translating "CISCO-CAPWAP-CONTROLLER.na.mscsoftware.com"...domain server (172.16.1.21)

Translating "CISCO-LWAPP-CONTROLLER.na.mscsoftware.com"...domain server (172.16.1.21) [OK]

*Mar  1 00:05:56.417: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar  1 00:05:56.546: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.na.mscsoftware.com
*Mar  1 00:06:06.614: %CAPWAP-3-ERRORLOG: Selected MWAR 'NA-HQ-WLC-01'(index 0).
*Mar  1 00:06:06.614: %CAPWAP-3-ERRORLOG: Go join a capwap controller
examining image...!
extracting info (295 bytes)
Image info:
    Version Suffix: k9w8-.124-25e.JAO6
    Image Name: c1130-k9w8-mx.124-25e.JAO6
    Version Directory: c1130-k9w8-mx.124-25e.JAO6
    Ios Image Size: 5028352
    Total Image Size: 5192192
    Image Feature: WIRELESS LAN|LWAPP
    Image Family: C1130
    Wireless Switch Management Version: 7.6.130.0
Extracting files...
c1130-k9w8-mx.124-25e.JAO6/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/file_hashes (3330 bytes)
*Apr  7 09:58:16.000:
extracting c1130-k9w8-mx.124-25e.JAO6/final_hash.sig (513 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/info (295 bytes)
c1130-k9w8-mx.124-25e.JAO6/html/ (directory) 0 (bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/ (directory) 0 (bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/1/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/forms.js (17486 bytes)! %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.21.21.21 peer_port: 5246
*Apr  7 09:58:17.811: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.21.21.21 peer_port: 5246
*Apr  7 09:58:17.812: %CAPWAP-5-SENDJOIN: sending Join Request to 172.21.21.21FirstCapwapVersionHasImage = 5.0.19.2
perform archive download capwap:/c1130 tar file
*Apr  7 09:58:17.879: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Apr  7 09:58:17.88!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/appsui.js (557 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/ap_home.shtml.gz (1304 bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/info.gif (399 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/cisco-logo-2007.gif (1648 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/background_web41.jpg (732 bytes)6: Loading file /c1130...

extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/login_homeap.gif (19671 bytes)!!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/config.js (24933 bytes)!!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/sitewide.js (16548 bytes)!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/officeExtendap.css (41795 bytes)!!!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/back.shtml (506 bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/15/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapBanner.htm (7108 bytes)!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapConfig.shtml.gz (2869 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapSummary.htm (712 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapHelp.htm (5007 bytes)!
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapMain.shtml.gz (3350 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapEvent.shtml.gz (983 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/final_hash (141 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6 (4757418 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
*Apr  7 10:00:17.876: %CAPWAP-3-ERRORLOG: Invalid event 48 & state 10 combination.
*Apr  7 10:00:17.876: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 48, state 10
*Apr  7 10:00:17.877: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Apr  7 10:00:17.877: %CAPWAP-3-ERRORLOG: Failed to process timer message.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
extracting c1130-k9w8-mx.124-25e.JAO6/7101.img (131328 bytes)!!!!!!!!!!
extracting c1130-k9w8-mx.124-25e.JAO6/6701.img (131328 bytes)!!!!!!!!!!
extracting info.ver (295 bytes)
Deleting target version: flash:/c1130-k9w8-mx.124-25e.JAO6...done.
New software image installed in flash:/c1130-k9w8-mx.124-25e.JAO6
Configuring system to use new image...done.
archive download: takes 334 seconds

Writing out the event log to nvram...

ReIniting the reap config file flash:/lwapp_reap.cfg
*Apr  7 10:03:53.116: %LWAPP-4-CLIENTEVENTLOG: No REAP configuration file to load. Connect to controller to get configuration file
*Apr  7 10:03:53.117: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Apr  7 10:03:53.117: image upgrade successfully, system is now reloading
*Apr  7 10:03:53.189: %SYS-5-RELOAD: Reload requested by capwap image download proc. Reload Reason: NEW IMAGE DOWNLOAD.
*Apr  7 10:03:53.193: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
flashfs[0]: 36 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7387648
flashfs[0]: Bytes available: 8611328
flashfs[0]: flashfs fsck took 30 seconds.
Base ethernet MAC Address: c4:71:fe:42:49:5e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"...###########################################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6" uncompressed and installed, entry point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team


Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[2]: 36 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 15740928
flashfs[2]: Bytes used: 7387648
flashfs[2]: Bytes available: 8353280
flashfs[2]: flashfs fsck took 4 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.

Radio0  present A506 7100 E8000000 A0000000 80000000 3
Rate table has 12 entries (0 SGI/0 BF variants)

Radio1  present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision B0) with 27638K/5120K bytes of memory.
Processor board ID FTX1448N0MK
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.6.130.0
1 FastEthernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C4:71:FE:42:49:5E
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14451A90
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FTX1448N0MK
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-A-K9
% Please define a domain-name first.


Press RETURN to get started!


Translating "CISCO-LWAPP-CONTROLLER.mscsoftware.com"...domain server (172.16.1.21)
*Mar  1 00:00:06.284: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar  1 00:00:07.704: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar  1 00:00:09.176: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar  1 00:00:09.248: %LINK-6-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:09.277: %LWAPP-4-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)

*Mar  1 00:00:10.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar  1 00:00:11.475: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team
*Mar  1 00:00:11.475: %SNMP-5-COLDSTART: SNMP agent on host NA-AA-AP1 is undergoing a cold start
*Mar  1 00:00:11.577: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar  1 00:00:11.579: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar  1 00:00:11.579: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:12.579: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar  1 00:00:12.579: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:13.640: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 22 seconds
*Mar  1 00:00:14.553: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

Translating "CISCO-CAPWAP-CONTROLLER.mscsoftware.com"...domain server (172.16.1.21)
*Mar  1 00:00:32.590: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.mscsoftware.com
*Mar  1 00:00:35.399: %LWAPP-3-CLIENTERRORLOG: rcb in dcb is NULL -Traceback= 0x59CDA0 0x5933B4 0x4767F8 0x469910 0x4699E0 0x46BAF8 0x47D210 0x47D678 0x1A5510
*Mar  1 00:00:35.399: %LWAPP-3-CLIENTERRORLOG: lwapp_chan_send_channel_pwr_update : can not get rcb

*Mar  1 00:00:35.399: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2427 selected
*Mar  1 00:00:35.400: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:36.400: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

*Mar  1 00:00:50.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.mscsoftware.com
*Mar  1 00:00:50.592: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar  1 00:00:50.682: Starting Ethernet promiscuous mode
*Mar  1 00:00:50.856: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar  1 00:00:50.856: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:51.092: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to resetlwapp_crypto_init: MIC Present and Parsed Successfully

*Mar  1 00:00:51.324: Logging LWAPP message to 255.255.255.255.

*Mar  1 00:00:52.484: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar  1 00:00:52.544: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar  1 00:00:52.568: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar  1 00:00:53.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar  1 00:00:53.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar  1 00:00:53.582: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar  1 00:00:54.582: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar  1 00:03:21.388: %LWAPP-3-CLIENTERRORLOG: Switching to Standalone mode
*Mar  1 00:03:21.419: Flex Non AP-Specific config version mismatch. Clearing it! Current Version 7.6.130.0, stored file version 8.0.110.11
*Mar  1 00:03:21.419: LWAPP REAP CFG is not valid, please connect to Controller once
*Mar  1 00:03:21.947: %LWAPP-4-CLIENTEVENTLOG: No REAP configuration file to load. Connect to controller to get configuration file
*Mar  1 00:03:21.948: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
*Mar  1 00:05:42.388: %CAPWAP-3-STATIC_TO_DHCP_IP: Could not discover WLC using static IP. Forcing AP to use DHCP.
*Mar  1 00:05:50.609: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
*Mar  1 00:05:50.609: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar  1 00:05:50.663: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 172.16.143.215, mask 255.255.255.0, hostname NA-AA-AP1

*Mar  1 00:05:50.663: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
Translating "CISCO-CAPWAP-CONTROLLER.na.mscsoftware.com"...domain server (172.16.1.21)

Translating "CISCO-LWAPP-CONTROLLER.na.mscsoftware.com"...domain server (172.16.1.21) [OK]

*Mar  1 00:05:56.412: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar  1 00:05:56.540: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.na.mscsoftware.com
*Mar  1 00:06:06.606: %CAPWAP-3-ERRORLOG: Selected MWAR 'NA-HQ-WLC-01'(index 0).
*Mar  1 00:06:06.606: %CAPWAP-3-ERRORLOG: Go join a capwap controller
examining image...
extracting info (295 bytes)
Image info:
    Version Suffix: k9w8-.124-25e.JAO6
    Image Name: c1130-k9w8-mx.124-25e.JAO6
    Version Directory: c1130-k9w8-mx.124-25e.JAO6
    Ios Image Size: 5028352
    Total Image Size: 5192192
    Image Feature: WIRELESS LAN|LWAPP
    Image Family: C1130
    Wireless Switch Management Version: 7.6.130.0
Extracting files...
c1130-k9w8-mx.124-25e.JAO6/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/file_hashes (3330 bytes)
*
extracting c1130-k9w8-mx.124-25e.JAO6/final_hash.sig (513 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/info (295 bytes)
c1130-k9w8-mx.124-25e.JAO6/html/ (directory) 0 (bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/ (directory) 0 (bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/1/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/forms.js (17486 bytes)Apr  7 10:11:17.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.21.21.21 peer_port: 5246
*Apr  7 10:11:18.823: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.21.21.21 peer_port: 5246
*Apr  7 10:11:18.824: %CAPWAP-5-SENDJOIN: sending Join Request to 172.21.21.21FirstCapwapVersionHasImage = 5.0.19.2
perform archive download capwap:/c1130 tar file
*Apr  7 10:11:18.890: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/appsui.js (557 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/ap_home.shtml.gz (1304 bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/info.gif (399 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/cisco-logo-2007.gif (1648 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/background_web41.jpg (732 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/images/login_homeap.gif (19671 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/config.js (24933 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/sitewide.js (16548 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/officeExtendap.css (41795 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/1/back.shtml (506 bytes)
c1130-k9w8-mx.124-25e.JAO6/html/level/15/ (directory) 0 (bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapBanner.htm (7108 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapConfig.shtml.gz (2869 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapSummary.htm (712 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapHelp.htm (5007 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapMain.shtml.gz (3350 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/html/level/15/officeExtendapEvent.shtml.gz (983 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/final_hash (141 bytes)
extracting c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6 (4757418 bytes)

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

Error message sounds like the AP is in the wrong Regulatory Domain.

As what Rasika has requested, please post the following output:

1.  WLC:  sh sysinfo;

2.  AP:  sh version;

3.  AP:  sh inventory

Here are the outputs:

AP Show Version:

glunwa1220ve#show version
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 29-Jul-13 12:06 by prod_rel_team

ROM: Bootstrap program is C1140 boot loader
BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1)

glunwa1220ve uptime is 1 hour, 10 minutes
System returned to ROM by reload
System image file is "flash:/c1140-k9w8-mx.152-2.JB2/c1140-k9w8-mx.152-2.JB2"
Last reload reason:

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-LAP1142N-E-K9 (PowerPC405ex) processor (revision A0) with 81910K/49152K bytes of memory.
Processor board ID FCZ1408W021
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.4.110.0
1 Gigabit Ethernet interface
2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C4:7D:4F:3B:11:97
Part Number : 73-11451-06
PCA Assembly Number : 800-30554-03
PCA Revision Number : A0
PCB Serial Number : FOC14060FVW
Top Assembly Part Number : 800-31273-02
Top Assembly Serial Number : FCZ1408W021
Top Revision Number : A0
Product/Model Number : AIR-AP1142N-E-K9

Configuration register is 0xF

AP: Show Inventory

glunwa1220ve#show inventory

NAME: "AP1140", DESCR: "Cisco Aironet 1140 Series (IEEE 802.11n) Access Point"

PID: AIR-AP1142N-E-K9 , VID: V02, SN: FCZ1408W021

WLC: show sysinfo

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS

System Name...................................... gvenwc0006
System Location.................................. Vernier
System Contact................................... wls.group@givaudan.com
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.71.142.7
Last Reset....................................... Software reset
System Up Time................................... 23 days 0 hrs 36 mins 14 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

Configured Country............................... Multiple Countries:CH,NL,GB,AE,AT,DE,ES,IT,RU,SE,TR
Operating Environment............................ Commercial (0 to 40 C)

--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +40 C
External Temperature............................. +27 C
Fan Status....................................... OK

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 7
Number of Active Clients......................... 52

Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown

Burned-in MAC Address............................ 44:2B:03:B4:45:00
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 50

Many thanks.

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend
Maximum number of APs supported.................. 50

How many APs are currently attached to your WLC?

Only 26...

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

Console into the AP and use this command "capwap ap controller IP address ".

Hi,

I already tried that and got the exact same log messages.

David

Rasika Nayanajith
VIP Mentor VIP Mentor
VIP Mentor

Try " clear capwap private-config" on ur ap and see if that help

Sent from Cisco Technical Support iPhone App

Ok I could do it !

I tried to attach the AP's to another WLC and it worked. So I checked the configuration of my initial WLC and I could see that there were AP Policies configured... Gosh, that was so dump !

Many thanks for your help guys !

David

Hi David,

I faced exatly the same issue in a 1142 pool after upgrading the wlc to 7.4.110.  Only a part of the pool had the issue, and I also could also not register on other wlcs with the same release.

It looks like an ap hw. release issue, as I have no ap policies and  all aps are configured exactly the same.

I had to downgrade to 7.2 or 7.3 to be able to register agan this aps.

The new maintenance release 7.4.121 does not mention any 1142 caveats, so I expect that it is not resolved.

+++

What's you experience since you have posted the thread ?

Thank you,

Jacky

Hi Jacky,

Do you have any update on this issue?

thanks

Hi David,

I am having the same issue on 2602i and 3502i AP`s. What you mean by AP Policies?

thanks

Hi Rasik,

On version 7.5.102.0, I cannot run a CLEAR COMMAND on the AP. I configured telnet and credentials on the AP in order to check access it and check the log. See next:

APe4d3.f11e.a8e1#

APe4d3.f11e.a8e1#

APe4d3.f11e.a8e1#clear

                  ^

% Invalid input detected at '^' marker.

APe4d3.f11e.a8e1#

APe4d3.f11e.a8e1#

APe4d3.f11e.a8e1#clear ?

% Unrecognized command

APe4d3.f11e.a8e1#clear

APe4d3.f11e.a8e1#show capwap ip config

LWAPP Static IP Configuration

Primary Controller 172.23.111.23 

APe4d3.f11e.a8e1#

APe4d3.f11e.a8e1#show version

Cisco IOS Software, C2600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Tue 30-Jul-13 22:57 by prod_rel_team

ROM: Bootstrap program is C2600 boot loader

BOOTLDR: C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)

APe4d3.f11e.a8e1 uptime is 11 minutes

System returned to ROM by power-on

System image file is "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"

Last reload reason:

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco AIR-CAP2602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.

Processor board ID FGL1651Z0CV

PowerPC CPU at 800Mhz, revision number 0x2151

Last reset from power-on

LWAPP image version 7.5.102.0

1 Gigabit Ethernet interface

2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: E4:D3:F1:1E:A8:E1

Part Number                          : 73-14588-02

PCA Assembly Number                  : 800-37899-01

PCA Revision Number                  : A0

PCB Serial Number                    : FOC164928ZF

Top Assembly Part Number             : 800-38356-01

Top Assembly Serial Number           : FGL1651Z0CV

Top Revision Number                  : A0

Product/Model Number                 : AIR-CAP2602I-A-K9  

Configuration register is 0xF

APe4d3.f11e.a8e1#

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers