02-01-2013 04:30 PM - edited 07-03-2021 11:28 PM
Hello Guys,
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address. please help me.
Thank you
02-01-2013 04:36 PM
The AP needs an IP address. The wlc time has to be set correctly. Place the ap on the same subnet as the wlc a management interface. Management and AP manager needs to be set on the same VLAN/subnet.
Post the output of the AP booting from the console
Sent from Cisco Technical Support iPhone App
02-01-2013 04:56 PM
Hello Scott,
Thank you for the reply
Please find the attached file for the config, i found out that i have not updated the time on WLC but i did update the time on WLC and tested for other AP and this one too wont join the WLC. The ap are located remote.
atsg-wl1#show run | incl hostname
hostname atsg-wl1
atsg-wl1#test pb display
------------------------------
Display of the Parameter Block
------------------------------
Total Number of Records : 7
Number of Certs : 6
Number of Keys : 1
atsg-wl1#term length 0
atsg-wl1#show version | include Cisco IOS
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA3, RELEASE SOFTWARE (fc1)
atsg-wl1#show controller | include Radio AIR
Radio AIR-AP1131G, Base Address 0019.0737.02f0, BBlock version 0.00, Software version 5.80.15
Radio AIR-AP1131A, Base Address 0019.073b.02d0, BBlock version 0.00, Software version 5.80.15
atsg-wl1#show controllers d0 | include Current
Current Frequency: 2447 MHz Channel 8
Current CCK Power: 14 dBm
Current OFDM Power: 14 dBm
Current Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
atsg-wl1#show controllers d1 | include Current
Current Frequency: 5805 MHz Channel 161
Current Power: 17 dBm
Current Rates: basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
atsg-wl1#show run | include station-role
station-role root
station-role root
atsg-wl1#test pb disp
------------------------------
Display of the Parameter Block
------------------------------
Total Number of Records : 7
Number of Certs : 6
Number of Keys : 1
atsg-wl1#show int F0 | include address
Hardware is PowerPCElvis Ethernet, address is 0019.555f.ccfa (bia 0019.555f.ccfa)
atsg-wl1#show int | include Dot11Radio
Dot11Radio0 is up, line protocol is up
Dot11Radio1 is up, line protocol is up
atsg-wl1#show sntp | exclude SNTP
10.148.0.1 16 1 never
172.16.21.57 16 1 never
Broadcast client mode is enabled.
atsg-wl1#show run
Building configuration...
Current configuration : 6025 bytes
!
! Last configuration change at 19:35:46 UTC Thu Jan 31 2013 by didata
! NVRAM config last updated at 19:13:48 UTC Fri Feb 1 2013 by didata
!
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime localtime
service password-encryption
!
hostname atsg-wl1
!
logging buffered informational
logging console informational
enable secret 5
!
ip subnet-zero
ip domain name aspentech.com
ip name-server 10.96.16.230
ip name-server 10.148.0.249
ip name-server 10.32.19.1
!
!
aaa new-model
!
!
aaa group server radius rad_eap
server 10.16.16.123 auth-port 1645 acct-port 1646
!
aaa authentication login default group tacacs+ local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication enable default group tacacs+ enable
aaa authorization exec default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
aaa session-id common
no dot11 igmp snooping-helper
!
dot11 ssid
authentication open eap eap_methods
authentication network-eap eap_methods
guest-mode
infrastructure-ssid optional
!
dot11 network-map
power inline negotiation prestandard source
!
!
usernamepassword 7
username privilege 15 password 7
usernamep rivilege 15 password 7
!
!
class-map match-all _class_Protocol_301_C351
match access-group name Voice_Over_IP_301
class-map match-all _class_8
match ip dscp cs1
class-map match-all _class_0
match ip dscp default
class-map match-all _class_48
match ip dscp cs6
class-map match-all _class_18
match ip dscp af21
class-map match-all _class_24
match ip dscp cs3
class-map match-all _class_16
match ip dscp cs2
class-map match-all _class_34
match ip dscp af41
class-map match-all _class_26
match ip dscp af31
class-map match-all _class_40
match ip dscp cs5
class-map match-all _class_46
match ip dscp ef
class-map match-all _class_56
match ip dscp cs7
class-map match-all _class_10
match ip dscp af11
class-map match-all _class_32
match ip dscp cs4
!
!
policy-map _policy_Voice_Over_IP_202
class _class_Protocol_301_C351
set cos 6
policy-map _policy_fallback_policy
class _class_0
set cos 0
class _class_8
set cos 1
class _class_10
set cos 1
class _class_16
set cos 2
class _class_18
set cos 2
class _class_24
set cos 3
class _class_26
set cos 3
class _class_32
set cos 4
class _class_34
set cos 4
class _class_40
set cos 5
class _class_46
set cos 5
class _class_48
set cos 6
class _class_56
set cos 7
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
!
encryption mode wep mandatory mic key-hash
!
broadcast-key change 900
!
!
ssid
!
traffic-class background cw-min 5 cw-max 8 fixed-slot 2
traffic-class best-effort cw-min 5 cw-max 8 fixed-slot 6
traffic-class video cw-min 4 cw-max 6 fixed-slot 1
traffic-class voice cw-min 3 cw-max 7 fixed-slot 1
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
packet retries 32
fragment-threshold 2338
station-role root
rts threshold 2339
rts retries 32
world-mode legacy
no cdp enable
infrastructure-client
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
!
encryption mode wep mandatory mic key-hash
!
broadcast-key change 900
!
!
ssid aspen100abcdefgh
!
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role root
world-mode legacy
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 10.148.0.7 255.255.255.0
no ip route-cache
!
ip default-gateway 10.148.0.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip tacacs source-interface BVI1
ip radius source-interface BVI1
!
ip access-list extended Voice_Over_IP_300
permit 119 any any
permit ip any any
ip access-list extended Voice_Over_IP_301
permit 119 any any
permit ip any any
logging facility local0
snmp-server view iso_view iso included
snmp-server community admin view iso_view RW
snmp-server community all4114all view iso_view RW
snmp-server community ddbos2000 RO
snmp-server location ATSG
snmp-server contact James Lee
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host 192.135.137.12 ddbos2000
tacacs-server host 10.16.16.123 key 7
tacacs-server host 10.96.16.245 key 7
tacacs-server directed-request
radius-server host 10.16.16.123 auth-port 1645 acct-port 1646 timeout 5 retransmit 3 key 7
radius-server deadtime 120
radius-server vsa send accounting
radius-server vsa send authentication
!
control-plane
!
bridge 1 route ip
!
!
!
line con 0
transport preferred all
transport output all
stopbits 1
line vty 0 4
exec-timeout 0 0
transport preferred all
transport input all
transport output all
line vty 5 15
exec-timeout 0 0
transport preferred all
transport input all
transport output all
!
end
atsg-wl1#show run | incl hostname
hostname atsg-wl1
atsg-wl1#arch down /over /create-space tftp://10.148.0.118/images/c1130-rcvk $over /create-space tftp://10.148.0.118/images/c1130-rcvk9 w8-tar.12 te-space tftp://10.148.0.118/images/c1130-rcvk9w8-tar.123 -11.JX1.t ftp://10.148.0.118/images/c1130-rcvk9w8-tar.123-11.JX1.ta r
examining image...
Loading images/c1130-rcvk9w8-tar.123-11.JX1.tar from 10.148.0.118 (via BVI1): !
extracting info (273 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 1873920 bytes]
Image info:
Version Suffix: rcvk9w8-
Image Name: c1130-rcvk9w8-mx
Version Directory: c1130-rcvk9w8-mx
Ios Image Size: 1874432
Total Image Size: 1874432
Image Feature: WIRELESS LAN|LWAPP|RECOVERY
Image Family: C1130
Wireless Switch Management Version: 3.0.51.0
Extracting files...
Loading images/c1130-rcvk9w8-tar.123-11.JX1.tar from 10.148.0.118 (via BVI1): !
extracting info (273 bytes)
c1130-rcvk9w8-mx/ (directory) 0 (bytes)
extracting c1130-rcvk9w8-mx/c1130-rcvk9w8-mx (1867816 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
extracting c1130-rcvk9w8-mx/info (273 bytes)
extracting info.ver (273 bytes)!
[OK - 1873920 bytes]
Deleting current version...
Deleting flash:/c1130-k9w7-mx.123-7.JA3...done.
New software image installed in flash:/c1130-rcvk9w8-mx
Configuring system to use new image...done.
atsg-wl1#show archive status
SUCCESS: Upgrade complete.
atsg-wl1#write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
atsg-wl1#dir flash:
Directory of flash:/
2 -rwx 2072 Jan 31 2013 19:36:18 +00:00 private-multiple-fs
149 drwx 128 Jan 31 2013 19:36:11 +00:00 c1130-rcvk9w8-mx
4 -rwx 342 Jan 31 2013 19:36:14 +00:00 env_vars
15998976 bytes total (14126080 bytes free)
atsg-wl1#dir nvram:
Directory of nvram:/
30 -rw- 0
31 ---- 0
1 -rw- 0
2 ---- 12
32768 bytes total (30668 bytes free)
atsg-wl1#sh crypto ca trustpoints
atsg-wl1#sh crypto ca certificates
atsg-wl1#terminal length 0
atsg-wl1#show run | begin BVI1
interface BVI1
ip address 10.148.0.7 255.255.255.0
no ip route-cache
!
ip default-gateway 10.148.0.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip tacacs source-interface BVI1
ip radius source-interface BVI1
!
ip access-list extended Voice_Over_IP_300
permit 119 any any
permit ip any any
ip access-list extended Voice_Over_IP_301
permit 119 any any
permit ip any any
logging facility local0
snmp-server view iso_view iso included
snmp-server community admin view iso_view RW
snmp-server community all4114all view iso_view RW
snmp-server community ddbos2000 RO
snmp-server location ATSG
snmp-server contact James Lee
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host 192.135.137.12 ddbos2000
tacacs-server host 10.16.16.123 key 7
tacacs-server host 10.96.16.245 key 7
tacacs-server directed-request
radius-server host 10.16.16.123 auth-port 1645 acct-port 1646 timeout 5 retransmit 3 key 7
radius-server deadtime 120
radius-server vsa send accounting
radius-server vsa send authentication
!
control-plane
!
bridge 1 route ip
!
!
!
line con 0
transport preferred all
transport output all
stopbits 1
line vty 0 4
exec-timeout 0 0
transport preferred all
transport input all
transport output all
line vty 5 15
exec-timeout 0 0
transport preferred all
transport input all
transport output all
!
end
02-01-2013 08:18 PM
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA3, RELEASE SOFTWARE (fc1)
This is not a controller-based IOS. It's still autonomous.
02-01-2013 08:20 PM
Leo,
Scroll down more:
atsg-wl1#arch down /over /create-space tftp://10.148.0.118/images/c1130-rcvk $over /create-space tftp://10.148.0.118/images/c1130-rcvk9 w8-tar.12 te-space tftp://10.148.0.118/images/c1130-rcvk9w8-tar.123 -11.JX1.t ftp://10.148.0.118/images/c1130-rcvk9w8-tar.123-11.JX1.ta r
examining image...
Loading images/c1130-rcvk9w8-tar.123-11.JX1.tar from 10.148.0.118 (via BVI1): !
extracting info (273 bytes)!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 1873920 bytes]
Sent from Cisco Technical Support iPhone App
02-01-2013 04:59 PM
Well if the AP is remote, how does that ap know about the WLC. You need to read this doc as it explains what you can do to help the AP join the wlc.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
Sent from Cisco Technical Support iPhone App
02-01-2013 05:07 PM
Scott,
Yes i have read the document and by that document i did everyting right except time setup on wlc. But i can see the debug messages saying hthe below:
*Feb 02 05:55:54.335: 00:19:55:5f:cc:fa Received LWAPP DISCOVERY REQUEST to ff:ff:ff:ff:ff:ff on port '1'
*Feb 02 05:55:54.335: Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 6,joined Aps =1
*Feb 02 05:55:54.335: 00:19:55:5f:cc:fa Successful transmission of LWAPP Discovery Response to AP 00:19:55:5f:cc:fa on port 1
*Feb 02 05:56:31.820: Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 6,joined Aps =1
*Feb 02 05:57:20.194: 00:19:55:5f:cc:fa Received LWAPP DISCOVERY REQUEST to ff:ff:ff:ff:ff:ff on port '1'
*Feb 02 05:57:20.194: Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 6,joined Aps =1
*Feb 02 05:57:20.194: 00:19:55:5f:cc:fa Successful transmission of LWAPP Discovery Response to AP 00:19:55:5f:cc:fa on port 1
*Feb 02 05:57:57.276: Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 6,joined Aps =1
*Feb 02 05:58:46.051: 00:19:55:5f:cc:fa Received LWAPP DISCOVERY REQUEST to ff:ff:ff:ff:ff:ff on port '1'
*Feb 02 05:58:46.051: Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 6,joined Aps =1
*Feb 02 05:58:46.051: 00:19:55:5f:cc:fa Successful transmission of LWAPP Discovery Response to AP 00:19:55:5f:cc:fa on port 1
02-01-2013 08:25 PM
Ooooooooooooooooooooooooooooooooooooooooooooooooooooooooo
02-01-2013 08:26 PM
LOL
Sent from Cisco Technical Support iPhone App
02-01-2013 06:01 PM
So what discovery are you doing?
Sent from Cisco Technical Support iPhone App
02-01-2013 06:06 PM
lwapp
02-01-2013 06:12 PM
That is the protocol, what discovery method are you using so that the AP can join the WLC. If you don't use one of the process that was in the link I sent, how does the AP find the wlc? It like me plugging in an AP at home and it trying to find your WLC.
Here is another doc you need to reference. This is also stated in the other document I referenced by a link.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml
Sent from Cisco Technical Support iPhone App
02-01-2013 06:34 PM
oh ok sorry i am new to wireless world.
I have turn on the OTAP on the WLC.
The APs used to have the Static IP and i have taken care that they remain a static but they dont seems to get an IP for themself. Help me out please.
02-01-2013 06:42 PM
OTAP will not help you.... do you have console access to the AP? If so, can you console into the AP and power up the AP and post the output.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
02-01-2013 07:18 PM
no they are remotely located so i dont have console access. i can see them on the switch to which they are attached with hostname ap and no ip address.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: