Resolved! OID - AP count
Hello,I'm looking for SNMP OID for vWLC 9800 that allows monitoring AP count connected to WLC. Is this possible? Does WLC return such counter via SNMP ?
Forum Posts
Hello Cisco WLAN experts,being relatively new on the new 9800-WLC-platform, I noticed recently that AP outages are not recognized on the 9800-WLC running 17.9.3-code. The missing AP is a AIR-AP3802I-E-K9 for example.I cannot see any information abou...
Resolved! Cisco AP stby 9115
I would like to operate 2 products of cisco ap 9115. You set the virtual controller IP for the two APs to XXX.XXX.XXX.232. IP was set to 233 and 234 respectively as an Access Point. If you boot after setting it up like this, one AP will ...
Resolved! Mobility Express and Aironet 3800
Hi All!I have a 3800i (second hand) and I'm banging my head against the wall with setting up Mobility Express. I was a CCNP back when CLI and IOS were the de facto, and this new era of devices are either too easy or too hard...I've (seemingly) succe...
I have a 150AX and two mesh extenders. I run three WLAN's with three SSID's mapped to three VLANs. About a week ago I noticed the devices I use on two of the WLAN's were not connecting to the WiFi. I did the usual power the device down, etc etc. Fina...
We are merging with another company and as a temporary solution until we can fully merge into one company we are going to run 2 completely separate wireless networks. Currently the offices are running a full Meraki wireless solution. We are going to ...
Resolved! RF Profile vs Global Configuration
Hi Guys,I want to enable client threshold traps, so if exceeds a certain amount of client that is being handled by the AP, PI will send an alert stating that the AP might be overload. On the WLC, I found the setting on RF profile, but could not find ...
Hi,users are complaining when they connect dot1x , it s disconnecting they need to reconnect but where as wpa2 it does not disconnect .What are the troubleshooting steps Thanks
So, this is more a question of what people are using or seeing. We will be replacing all our facilities this year and I plan to go Wi-Fi6E. I have tested having the SSID with mixed, but I have also heard separate doe to if a client shifts frequencies...
I have a single google home that will not stay connected to wireless. This is a network consisting of only two 9115aps and nothing else in the network its having the issue. There is a single google home that disconnects daily and will not reconnect t...
Resolved! CISCO wireless tools
Hi all,I need a little clarification about Cisco wireless tools.Cisco WLC is basically to configure wireless network(ap,ap groups,radius,etc),isn't it?But when I need to monitor APs,clients,RFs,channels,etc...,Cisco WLC is not really "friendly",basic...
hello I'm trying to access the AP after setting up, but I can't. Is it possible to do log analysis? ap->radius server Ping communication is possible. ID/PW is also correct. When I try to connect to ssid on my device, I can't connect and the logs a...
Hi, i want to change lightweight mode to autnomous mode on my AIR-CAP2602I-E-K9Therefor I downloaded the software ap3g2-k9w7-tar.153-3.JF15 and rename it to ap3g2-k9w7-tar.default. The file starts with info 0000644 3347037 0000031 00000000435 1411306...
Hi all, We have installed AI-Enhanced RRM and configed all of the required configs on WLC and DNAC. However, the activities log keep showing this error message every 30 mins. I tried to assign building for enabling AI-Enhanced RRM. But the site and t...
We have wireless and wired devices that uses Bonjour (mDNS) service to discover each other. I need to configure both wired and wireless devices in the same VLAN . We have Cisco WLC 5520 and APs that support flexconnect feature. I need to configure AP...
