Wireless

I noticed that some times when I try to distribute the configuration of one AP to all the other, The distribution list is small. No matter what AP I try to distribute from. Other times it is fine and they all show up. There is a mix of 340's and 3...

Hi anyone, I have the following configurations and scenerio;My HQ office is using a 2610 with two ethernet ports (10 BASET Half-Duplex);eth0/0 - 210.188.31.84eth0/1 - 210.188.6.1 - Internal LANFrom eth0/0, it's connected to the ethernet port of the A...

We are currently testing the 1200 access point with the 802.11a radio. In testing the performance and distance, it appears that the radio card will not drop down to a lower speed to increase the distance. It continues to run at 54Mbps. Because of...

I have two BR350 units, one root, one non-root w/clients. I have Funk's steel-belted radius 3.0 and i have two win2k laptops. one laptop is running the latest firmware and ACU version and is connecting to the non-root bridge doing LEAP. I have eve...

Hi,Can anybody give me some insight into integration of WLSE with Cisco Works 2000 or HP OpenView. The problem is that in a organisation if i have 10 WLSE installed, as WLSE has a limitation of 500 APs, now how can i have a centralized management of ...

I am trying to test Mobile IP in a lab scenario. X ----ethernet 2620 serial.........serial2620ethernet -----YThe set up is like this. R1 and R2 are 2 2620s connected by serial link. R1 has ethernet falling in network X. R2 has ethernet falling in net...

I have Cisco Wireless Bridge 340s (AP). How I canadd/remove Control Node Access in Association table via SNMP?Otherwise, How I can block/unblock radiouser via SNMP?What is OID for this action? Answer me If possible with the examples please?This probl...

I have two 340 bridges. I can see the other nodes from the Network Neighborhood. I can transfer files without a problem. But when I try to open my excel files from the other network especially large files, request timeout occurs. Result is that I can...

Ok - after buying an aironet 350 + card and playing around with static WEP,LEAP, etc and getting everything working successfully, all of a sudden theWEP capabilities have just died. I can no longer even set up static WEP,even though it appears that m...

350 BridgeSystem Firmware 11.21Radio FirmwareLan to LanRight now is following security optins not set!MICWEBTKIPthe bridge switcing between those to messageLost Authentication with Parent andAssociated to Parent [W-LI2-1]0040963a6137and there can be ...

Hi...If there are so many mobile devices within an area, how do we identify who is at where? Can we use the MAC address? Would that be that of the WLAN card or the mobile device, say the PDA itself?Also, does anyone know how to get the MAC address? ...

Hi , Have any experience in upgrade of the above mention firmware 11.23t, My question is why the AP was reset to default setting any advise of what should I do before the firmware upgrades ThanksRegardsMcNAz

I can't configure a transmit power of 100mW on my AP350,max is 50mw I've installed firmware 11.23T (radio 4.25g) no changeDid i forget something somewhere to validate this transmit power?ThanksAlain

A vendor has just completed a site survey, and throughout the design, there will be 5 AP's (350's with 2dBi omni's) within 50' of each other in a X pattern. I am concerned that too many will lead to poor performance, as the channels will certainly o...

Hi,i'm using an aironet 350. When i setup an IP filter or an ip port filter, i've got the drop-down menu 'priority' with values that looks very close to QoS terms (Best Effort, Interactive Voice... )How does it works ? Does the aironet implement any ...