02-24-2020 03:14 PM - edited 07-05-2021 11:46 AM
Updated standalone access point 3702 (may be applied to all 1700, 2600, 2700, 3600, 3700 family) to new image ap3g2-k9w7-tar.153-3.JK and got WEB UI not working with "404 Not Found" error when Save Configuration pressed.
Update was performed using CLI:
User Access Verification Username: Cisco Password: ap>enable Password: ap# format flash: Format operation may take a while. Continue? [confirm] Format operation will destroy all data in "flash:".Continue? [confirm] flashfs: 0 files, 1 directories flashfs: 0 orphaned files, 0 orphaned directories flashfs: Total bytes: 31739904 flashfs: Bytes used: 1024 flashfs: Bytes available: 31738880 flashfs: flashfs fsck took 8 seconds. Format of flash: complete ap# archive download-sw /force-reload /overwrite tftp://10.1.0.2/ap3g2-k9w7-tar.153-3.JK.tar
examining image... Loading ap3g2-k9w7-tar.153-3.JK.tar from 10.1.0.2 (via BVI1): ! extracting info (280 bytes)
Image info: Version Suffix: k9w7-.153-3.JK Image Name: ap3g2-k9w7-mx.153-3.JK Version Directory: ap3g2-k9w7-mx.153-3.JK Ios Image Size: 10732032 Total Image Size: 13875712 Image Feature: WIRELESS LAN Image Family: AP3G2 Wireless Switch Management Version: 18.104.22.168 MwarVersion:080A6900.First AP Supported Version:07010100.
Image version check passed
Extracting files... ap3g2-k9w7-mx.153-3.JK/ (directory) 0 (bytes) extracting ap3g2-k9w7-mx.153-3.JK/ap3g2-k9w7-mx.153-3.JK (230195 bytes) extracting ap3g2-k9w7-mx.153-3.JK/ap3g2-k9w7-tx.153-3.JK (73 bytes) .....[cut extract process lines]..... extracting info.ver (280 bytes) [OK - 13916160 bytes] New software image installed in flash:/ap3g2-k9w7-mx.153-3.JK Configuring system to use new image...done. Requested system reload in progress... archive download: takes 127 seconds
After reboot AP successfully acquired IP address via DHCP, but doesn't start http server. Due to security reason in new firmware http server disabled by default and can't be enabled with default password for privileged (enable) mode. So this password needs to be changed and http server can be enabled.
User Access Verification Username: Cisco Password: ap>enable Password: ap#configure terminal Enter configuration commands, one per line. End with CNTL/Z. ap(config)#enable secret <mypass> ap(config)#ip http server ap(config)#end ap#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] ap#reload Proceed with reload? [confirm]
After reboot WEB UI appears, but many functions not working properly. For example if Save Configuration pressed error "404 Not Found" appears making impossible to configure AP using WEB UI.
I tested also 15.3.3 JPI1 and 15.3.3 JPI4 firmware. Same issues.
Latest working version is 15.3.3 JJ1
Does anybody have the solution for this problem?
02-29-2020 06:14 AM
Try upgrading to the latest version, there is one or two newer and see how it works. If still issues, try using different browsers. If still issues, raise a TAC case, as this year you still get bug fixes and development.
03-04-2020 09:34 AM - edited 03-04-2020 06:36 PM
Tested newest firmware - 15.3.3 JPJ2.
Now it's better, but still not usable. In this version Cisco fixed most of WEB UI pages, but radio interface settings page is not working: controls are empty and Apply button has no effect.
NETWORK -> NETWORK INTERFACE -> Radio0-802.11N xxx -> SETTINGS
04-22-2020 10:56 AM
I have the same issue even with JPJ3.
Anyone solved this ?
04-24-2020 01:35 AM
04-02-2020 06:47 AM
Hi, I have exactly the same problem. Cisco is so good that they release software without testing! Pros!
The problem is basic and reproducible in 100%.
11-27-2020 03:51 AM
In the following video step by step process has been shown How to Configure Cisco AIRONET 3602i Autonomous/Standalone Access Point using GUI with WPAv2 Authentication Key.
Configuring Aironet Access Point with WPAv2 Authentication in GUI :
1. In Easy Setup
Under Network Configuration
Edit AP hostname, Static IP, Subnet mask and Default Gateway
Under In Radio Configuration
Create SSID name WLAN_New under Radio 2.4GHz and select Broadcast SSID in Beacon
2. Apply Encryption Modes to AES CCMP
3. Enable WPAv2 and apply WPA Pre-shared Key: to SSID
4. Enable Wireless Radio Interface (Radio0-802.11N2.4GHz/ Radio1-802.11N5GHz) UP
5. Save the configuration
6. Finally check the SSID Wi-Fi connection, Security Key, IP address and browsing through internet
06-17-2021 11:46 PM
I think with version JPK its solved ( at least on my side )
07-14-2021 12:33 AM
It claims it is fixed, but with the JPK1 i'm still getting the 404 error when saving the config. So the issues are most def not solved with the web GUI.
08-16-2021 04:55 AM
How did you solved it?
03-04-2022 05:43 PM
I am having an Arionet 3702E and experiencing the same issue.
"404 Not Found"
I tried the following firmware:
Both having the same issue.
Going to try ap3g2-k9w7-tar.153-3.JJ1.tar next.
03-05-2022 11:31 PM
Tried a few more firmware and the web ui is still not working fully.
Here are the firmware I tried:
Ending up using the Cisco Network Assistant.
03-10-2022 04:55 AM
Did the CNA Worked?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: