12-06-2012 12:08 AM - edited 07-03-2021 11:10 PM
Hi All,
I just configured Aironet 3502i and it works ok but no lights. I could see the AP in switch, in WLC, and in WCS and ping ok but when you see it mounted it has no light. I tried to shutdown the port in the switch and I saw it turns green (booting), once it was registered in WLC the light will be off.
Currently I have 4 AP's with same issue that has no light but working. Any tip for this?
Solved! Go to Solution.
12-18-2012 10:00 AM
12-06-2012 01:05 AM
What does "show ap led-state
12-06-2012 01:42 AM
Hi Matthew,
No "show ap led-state
12-06-2012 01:47 AM
Shame, there is at least on version 7.3 on our 5508s.
Could also try "show capwap client config" on the AP. At least on the firmware we're running there's a "Led State Enabled" line in the output with the current LED state.
12-17-2012 11:00 PM
Hi matt,
sorry for the late reply, very busy pass few days.
WLC >> Wireless >> All Ap's >> AP >> General >> Version
Primary Software Version 7.0.116.0
Backup Software Version 0.0.0.0
Predownload Status None
Predownloaded Version None
Predownload Next Retry Time NA
Predownload Retry Count NA
Boot Version 12.4.23.5
IOS Version 12.4(23c)JA2
Mini IOS Version 7.3.1.73
12-06-2012 10:55 AM
Wireless>> Access Points>> Global Configuration>> General>> Check LED state to enable.
If above is already enabled then try the below option.
Wireless>> Access Points>> All APs>> select an AP>> Goto advanced tab>> check 'LED state to enable'. Do this on all AP.
12-17-2012 11:07 PM
Hi Saravanan,
I did not see LED state in advance tab of our WLC. See version below.
WLC >> Wireless >> All Ap's >> AP >> General >> Version
Primary Software Version 7.0.116.0
Backup Software Version 0.0.0.0
Predownload Status None
Predownloaded Version None
Predownload Next Retry Time NA
Predownload Retry Count NA
Boot Version 12.4.23.5
IOS Version 12.4(23c)JA2
Mini IOS Version 7.3.1.73
12-18-2012 10:00 AM
this should work
wlc>config ap led-state enable all
12-20-2012 06:31 PM
Hi Saravanan,
Thank you for the CLI command, everything works ok.
12-20-2012 07:27 PM
Hi Denz
You're welcome!!!
Thanks.
02-04-2013 11:29 AM
Had the same issue here, the last few APs installed (Aironet 1041N and 1042N models) left their lights off once they joined the controller. The show command didn't work but the config command did the trick perfectly, with the WLC responding that it had "Successfully set LED-State for AP" for the last nine that I installed.
For reference, WLCs are running 7.0.235.0.
Thanks for the solution!
03-04-2013 12:40 AM
This document was generated from the following discussion: Cisco Aironet 3502i AP has no light.
06-03-2013 12:38 AM
Hello,
CSCud76044 - LWAPP LED fails to glow after booting up
Symptom:
LWAPP AP LED switches off after booting up.
Conditions:
LWAPP AP running mini IOS 7_3_1_73. AP need not have joined controller for the issue to manifest.
mini IOS 7_3_1_73 is equal to bootloader version 12.4(23c)JA5.
Workaround:
config ap led-state enable from the controller.
First Found in:
12.4(23c)JA5
Fixed in:
7.0(240.1)
Status: Fixed (Verified)
https://supportforums.cisco.com/docs/DOC-30253
Thanks,
Vinay Sharma
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: