cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1927
Views
0
Helpful
3
Replies

Cisco AP 2802i Not Joining with WLC-2500

shicailiu8372
Level 1
Level 1

My Cisco AP 2802i Not Joining with WLC-2500. it is the only ap i want to connect to WLC.

[*12/05/2019 17:30:38.3775] SYS-COND: AP is in fair condition
[*12/05/2019 17:30:38.8789] DOT11_CFG[0] Radio Mode is changed from Local to Local
[*12/05/2019 17:30:38.8827] DOT11_CFG[1] Radio Mode is changed from Local to Local
[*12/05/2019 17:30:38.9025] AP IPv4 Address updated from 0.0.0.0 to 192.168.100.4
[*12/05/2019 17:30:39.6212] dtls_init: Use SUDI certificate
[*12/05/2019 17:30:39.6215]
[*12/05/2019 17:30:39.6215] CAPWAP State: Init
[*12/05/2019 17:30:39.6220]
[*12/05/2019 17:30:39.6220] Config not found, PNP is required, Starting PNP
[*12/05/2019 17:30:39.6220]
[*12/05/2019 17:30:43.2854] PNP:Server not reachable, Start CAPWAP Discovery
[*12/05/2019 17:30:43.2857]
[*12/05/2019 17:30:43.2857] CAPWAP State: Discovery
[*12/05/2019 17:30:43.2882] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*12/05/2019 17:30:43.2882]
[*12/05/2019 17:30:43.2882] CAPWAP State: Discovery
[*12/05/2019 17:30:43.2897] Discovery Response from 192.168.100.10
[*12/06/2019 11:12:28.0000] can't find the Ip from discoveryRequest array
[*12/06/2019 11:12:28.0000]
[*12/06/2019 11:12:28.0001]
[*12/06/2019 11:12:28.0001] CAPWAP State: DTLS Setup
[*12/06/2019 11:12:28.6747]
[*12/06/2019 11:12:28.6747] CAPWAP State: Join
[*12/06/2019 11:12:28.6772] Sending Join request to 192.168.100.10 through port 5272
[*12/06/2019 11:12:28.6793] Join Response from 192.168.100.10
[*12/06/2019 11:12:28.7696] HW CAPWAP tunnel is ADDED
[*12/06/2019 11:12:28.7871]
[*12/06/2019 11:12:28.7871] CAPWAP State: Image Data
[*12/06/2019 11:12:28.8237] do NO_UPGRADE, part1 is active part
[*12/06/2019 11:12:28.8289]
[*12/06/2019 11:12:28.8289] CAPWAP State: Configure
[*12/06/2019 11:12:28.8313] DOT11_CFG[0] Radio Mode is changed from Local to Local
[*12/06/2019 11:12:28.8319] DOT11_CFG[1] Radio Mode is changed from Local to Local
[*12/06/2019 11:12:31.6105] Re-Tx Count=1, Max Re-Tx Value=5, SendSeqNum=1, NumofPendingMsgs=1
[*12/06/2019 11:12:31.6105]
[*12/06/2019 11:12:34.4613] Re-Tx Count=2, Max Re-Tx Value=5, SendSeqNum=1, NumofPendingMsgs=1
[*12/06/2019 11:12:34.4613]
[*12/06/2019 11:12:37.3122] Re-Tx Count=3, Max Re-Tx Value=5, SendSeqNum=1, NumofPendingMsgs=1
[*12/06/2019 11:12:37.3122]
[*12/06/2019 11:12:40.1631] Re-Tx Count=4, Max Re-Tx Value=5, SendSeqNum=1, NumofPendingMsgs=1
[*12/06/2019 11:12:40.1631]
[*12/06/2019 11:12:43.0139] Re-Tx Count=5, Max Re-Tx Value=5, SendSeqNum=1, NumofPendingMsgs=1
[*12/06/2019 11:12:43.0139]
[*12/06/2019 11:12:45.8648] Re-Tx Count=6, Max Re-Tx Value=5, SendSeqNum=1, NumofPendingMsgs=1
[*12/06/2019 11:12:45.8648]
[*12/06/2019 11:12:45.8648] Max retransmission count exceeded, going back to DISCOVER mode.
[*12/06/2019 11:12:45.8649] GOING BACK TO DISCOVER MODE
[*12/06/2019 11:12:45.8655]
[*12/06/2019 11:12:45.8655] CAPWAP State: DTLS Teardown
[*12/06/2019 11:12:51.6794]
[*12/06/2019 11:12:51.6794] CAPWAP State: Discovery
[*12/06/2019 11:12:51.6851] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*12/06/2019 11:12:51.6858] Discovery Response from 192.168.100.10
[*12/06/2019 11:13:01.0000] can't find the Ip from discoveryRequest array
[*12/06/2019 11:13:01.0000]

3 Replies 3

Leo Laohoo
Hall of Fame
Hall of Fame

@shicailiu8372 wrote:

[*12/06/2019 11:12:28.6772] Sending Join request to 192.168.100.10 through port 5272
[*12/06/2019 11:12:28.6793] Join Response from 192.168.100.10


Post the complete output to the following commands: 

1.  WLC:   sh sysinfo; 

2.  WLC:  sh time; 

3.  WLC:  sh ap join stats detailed <AP name>; and

4.  AP:  sh version

Hi bor , thank you for your advice. I solve the problem alr. I use the wrong contry code . the ap 2802i-D is made in india. 

HI,

In addition to the commands mentioned by Leo, if you still cannot register, you can collect the following debug information:

WLC debugs:
WLC> debug mac addr < AP MAC address >
WLC> debug capwap errors enable
WLC> debug capwap events enable
WLC> debug dtls all enable
WLC> debug pm pki enable
To disable debugs: debug disable-all

AP debugs:
AP# debug capwap client event
AP# debug capwap client error
AP# debug capwap client detail
AP# debug dtls client error
AP# debug dtls client event
To disable debugs: u all
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Rps-Cheers | If it solves your problem, please mark as answer. Thanks !
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: