cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
576
Views
5
Helpful
5
Replies

Cisco AP1532E not Joining Controller 2500

melki_zedek
Beginner
Beginner

I am facing issue with AP1532E joining to controller 2500.

AP light flashing from green,red, yellow, green

Below is the repeated log message. I have attached the full log from boot up to the repeating message.

*Jun 27 10:30:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.10.251 peer_port: 5246
*Jun 27 10:30:34.479: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.10.251 peer_port: 5246
*Jun 27 10:30:34.479: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.10.251
*Jun 27 10:30:52.643: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.10.251:5246
*Jun 27 10:30:52.739: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
*Jun 27 10:30:52.739: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jun 27 10:30:52.739: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jun 27 10:30:53.263: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 27 10:30:53.263: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 27 10:30:53.771: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jun 27 10:30:53.779: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jun 27 10:30:54.771: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jun 27 10:30:54.815: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jun 27 10:30:54.823: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jun 27 10:30:54.831: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jun 27 10:30:55.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jun 27 10:30:55.823: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 27 10:30:55.851: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 27 10:30:56.851: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 27 10:31:06.259: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.

I will be very grateful for your help asap.

Thank you,
Benjamin.

5 Replies 5

Pls post "show sysinfo" from your WLC.

As per your AP detail make sure your WLC is configured for a proper country code in -E domain and also it has software code 7.6.x or above (preferably 8.0.133.0)

 AIR-CAP1532E-E-K9

http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html#56735

HTH

Rasika

*** Pls rate alll useful responses ***