- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-03-2015 02:50 AM - edited 07-05-2021 02:38 AM
Dear Friends,
I am using Cisco WLC 2504 current software version is 7.0.220.0 and I want to upgrade it to the latest version which is 8.x.x.x.
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Thank you very much for your help and support.
Thanks
Umar
Solved! Go to Solution.
- Labels:
-
Wireless LAN Controller
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-03-2015 11:40 AM
Hi
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Yes, you can go directly to 8.0.x from 7.0.x code. Refer below link
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80mr1.html#68333
Make sure you refer the release notes for any known issues with this code. Also upgrade FUS to 1.9.0.0 as well. This will take around 30 min downtime as well.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
If you have different AP models, MSE, Prime products, refer this compatibility matrix as reference.
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
HTH
Rasika
**** Pls rate all useful responses ****
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-03-2015 11:40 AM
Hi
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Yes, you can go directly to 8.0.x from 7.0.x code. Refer below link
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80mr1.html#68333
Make sure you refer the release notes for any known issues with this code. Also upgrade FUS to 1.9.0.0 as well. This will take around 30 min downtime as well.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
If you have different AP models, MSE, Prime products, refer this compatibility matrix as reference.
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
HTH
Rasika
**** Pls rate all useful responses ****
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-04-2015 01:05 AM
Hi Rsika,
Thank you very much for your reply. I’ll go through the documents and let you know if I need further help probably I do :).
Thanks
Umar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-05-2015 03:22 AM
Hi Rasika,
I have followed your instructions and successfully upgraded the software and FUS.
Thank you very much for your help.
Kind Regards
Umar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-05-2015 11:00 AM
Good to hear that & glad I was able to help you..
Rasika
