cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1948
Views
15
Helpful
12
Replies

Cisco WLC 9800 DHCP option 82

AndreVal
Level 1
Level 1

Hi everyone,

My ISP requires to insert option 82 to every clients' DHCP request, so I was trying to configure that on my 9800-80 controller. No issues with the Remote Agent ID, I was able to insert eth_apmac and ssid. But I can't seem to find how to insert Agent Circuit ID. Documentation guides don't really say anything about that either. I'm also using AireOS WLCs and they insert circuit-id suboption with no problems (by default it's 00000000). Maybe it was abolished by Cisco and new WLCs won't insert circuit-id tag?

AireOS Cisco WLC 8540:

Old Cisco 8540Old Cisco 8540

IOS-XE Cisco WLC 9800:

New Cisco 9800New Cisco 9800

12 Replies 12

marce1000
VIP
VIP

 

 - Ref : https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9800-series-wireless-controllers/guide-c07-743627.html

>...

DHCP relay can be configured on the C9800 as well, but in that case a Layer 3 VLAN interface (SVI) needs to be configured to source such traffic. You may want to configure DHCP relay on the C9800 for multiple reasons. For example:

●      The wireless team doesn’t have access to the next-hop switch configuration.

●      You want to add option 82 information to the DHCP server.

The recommended way to configure DHCP relay on the Catalyst 9800 is under the “Advanced” tab of the SVI configuration: Configuration > Layer2 > VLAN; you can also define multiple DHCP servers and the option 82 relay settings:

marce1000_0-1663053517632.png

 

Layer2 > VLAN" width="720" height="802" border="0">

 M.



-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
    When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Hello!

Thanks for replying, I tried that configuration but non of those options would insert Agent Circuit ID. 

 

 - Check if this document contains extra info's : https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/config-guide/b_wl_16_10_cg/dhcp-option82.html

 M.



-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
    When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Seen that too, they do mention Circuit id there, but nothing related to the specific configuration. 

The Circuit ID suboption includes information that is specific to the circuit the request came in on. This suboption is an identifier that is specific to the relay agent. Thus, the circuit that is described will vary depending on the relay agent.

 

- Note 100% sure that the 9800 can do it  , attached you will output from the feature navigator https://cfnng.cisco.com/browse/switching/features , for DHCP Option 82 Configurable Circuit ID and Remote ID

 M.



-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
    When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

thanks for the document, but I even tried to upgrade to the latest IOS-XE they have (17.09.01) but still nothing, this is the best result I could get (everything but circuit-id haha):

Screenshot 2022-09-13 at 22.53.29.png

As I know the ssid is the circuit-id  for wireless 
and port/vlan is the the circuit-id for wire

ssid goes to Remote Agent ID, while circuit-id was always fixed for WLCs - 00000000. 

https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/config-guide/b_wl_16_10_cg/dhcp-option82.html

this guide 
we can config WLC Op82
RID <<- this work for you
Circuit-id << guide not mention it 
can you use instead of circuit-id the  subscriber-ID ? 



RID didn't really help here too. I suppose subscriber-id is the only option for us here and I should talk to ISP about using that instead. 

Rich R
VIP
VIP

Although https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-9/config-guide/b_wl_17_9_cg/m_pol_dhcp_option82_vewlc.html says this in the intro info:
"This option works by setting two suboptions:

  • Circuit ID

  • Remote ID

The Circuit ID suboption includes information that is specific to the circuit the request came in on."
I don't think they support Circuit ID on 9800 so far.  That will need a feature request through TAC and your account team (if they don't already have one).  We managed to get a number of these raised as bugs (sev 3 rather than sev 6) on the basis of providing feature parity with AireOS because they were eager to help migrate customers off AireOS.  Not sure if they'll still be receptive to that but you can try.  Assuming they accept it as a feature parity bug then best you can hope for is for it to be included in 17.10.1 and if you're really persuasive they might back-port it to 17.9 for you.

Yep, seems like feature request is the way. But aside that ISP thing I can't imagine using it somewhere else. I think I'll talk to them first and ask about other options first. Anyway, thanks for your help!

Review Cisco Networking for a $25 gift card