cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
186
Views
5
Helpful
6
Replies

Deploying 9124s vertically on pole - Solar Shield Required?

We are deploying Cisco 9124s vertically on poles. I read that Cisco recommends using solar shield in outdoor deployments in direct sunlight, but in the installation documentation, the deployments it shows using the solar shield horizontally to shade the fins of the heat sink. It does not show any solar shield on the vertical deployments (i.e. with the paintable cover). So my question is, do any of you have experience deploying 9124s vertically on poles? If so, did you use a solar shield, or is it in fact designed to shade the heat sink fins on horizontal deployments with the L bracket as we suspect?

1 Accepted Solution

Accepted Solutions

Oh wait ... I totally got confused.  

For vertical installation, there is no room to install a solar cover, however, we will install a Cover Kit.  

View solution in original post

6 Replies 6

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

I am in Australia and solar-shield is mandatory for the following reasons: 

  1. Daytime temperature can go from mid-30 (Celsius) to 50 (Celsius)
  2. Very dry and arid condition
  3. Bird dropping

So how do you install a solar shield on a vertical deployment? Or are all of yours horizontal using the L bracket?

Thanks M8!

Oh wait ... I totally got confused.  

For vertical installation, there is no room to install a solar cover, however, we will install a Cover Kit.  

Thanks - so do you consider the Cover Kit as environmental protection or just cosmetic?

 

Thanks again!

Both.  

We are installing them to stop the birds from nesting on them.

Rich R
VIP Advisor VIP Advisor
VIP Advisor

When the 9124 was launched I remember Cisco saying it was already sun rated so did not require a solar shield.
The specs: Operating temperature -40 C to 65 C (55 C with solar loading).
But that said, the installation guide still recommends it so probably better to use it.
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/9124ax/install-guide/b-hig-9124ax/installation-overview.html

 

___________________________________________
TAC recommended codes for AireOS WLC's
Best Practices for AireOS WLC's
TAC recommended codes for 9800 WLC's
Best Practices for 9800 WLC's
Cisco Wireless compatibility matrix
Field Notice: FN-72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Recommended
WARNING - see CSCwd37092 Throughput degraded after upgrading to code 8.10.181.0/17.3.6 - 2800/3800/4800 series
- The fix for CSCwd37092 is now released in 8.10.183.0 and
- For IOS-XE 17.3.6 select controller model, go to IOS XE Software AP Service Pack, select CSCwd40096 17.3.6 APSP2
Field Notice: FN-63942 Lightweight APs and WLCs Fail to Create CAPWAP Connections Due to Certificate
                      Expiration - Software Upgrade Recommended
Field Notice: FN-72524 - During Software Upgrade/Downgrade IOS APs Might Remain in Downloading State
                     After 4 Dec 2022 Due to Certificate Expiration - Fixed in 8.10.183.0 and 17.3.6 APSP5 (APSP_CSCwd83653)
                     Also fixed in 8.5.182.7 (8.5 mainline) and 8.5.182.105 (8.5 IRCM) if you can't upgrade to 8.10
                     Note that 8.10.181.0 and 8.10.182.0 have been deferred (withdrawn) and are effectively unsupported by Cisco
___________________________________________
Richard R
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers