cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1371
Views
25
Helpful
17
Replies
gglynn
Beginner

Multiple VLANs on one SSID: how does this actually work?

I'm familiar with the procedure for bridging multiple VLANs between two Aironet bridges (e.g. 1300 series) over a single SSID, but I have no idea how it works, and that really bugs me.

Since frame tagging a la 802.1q isn't part of the WiFi protocols (at least I don't think it is), how do the bridges differentiate traffic in the 802.11 packets? Is there some Cisco-proprietary extension of the standards to support 802.1q tags in the 802.11 headers? Or is it something else?

17 REPLIES 17
b.julin
Participant

As far as I know, the controller simply differentiates each client and places them on the configured VLAN. I don't think the LWAPs have any idea what VLANs are even in use. Could be wrong there, but my bet is it is all done on the controller.

This particular question doesn't involve LWAPP controllers, it's about Aironet bridges, which run IOS.

Bump.

bcolvin
Participant

George

In addition to the Native VLAN for the AP IP subnet, you will need to create an SSID/VLAN pair for for each VLAN you want to bridge the .1q trunking on the switch should do the rest.

I strongly suggest that you use the WEB interface to configure the VLAN's as doing iit with the CLI is both cumbersome and prone to error.

This link explains it

http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml

Good Luck

Bill

Hi, Bill,

Thabks for the reply, but I'm familiar with how to set it up, and have done so a number of times. My question boils down to, "How does it actually work?"

-George

George

The AP in autonomous mode is basicaly a layer two device and does not know about IP and VLAN's this is a good question.

to answer your original question "Multiple VLANs on one SSID: how does this actually work?" the answer is from Cisco is "Failure to recognize that multiple VLANs and SSIDs indicate multiple OSI Model Layer 3 subnets

Deprecated versions of Cisco Aironet software permit binding multiple SSIDs to one VLAN. Current versions do not"

The Packet headers have a VLAN tag field that the Switch or AP decodes/inserts depending on direction to determine the correct routing,

that is the short version

Bill

I'm afraid that I'm confused by your answer, Bill. Which "packet headers" have a "VLAN tag"? The wireless (802.11) packets? Which header field is it in? And why would a layer 2 device necessarily not understand VLANs? 802.1q is a layer 2 VLAN tagging protocol.

Keep in mind I'm specifically asking about *bridging* VLANs across a point-to-point wireless link using a single SSID, not about associating VLANs with SSIDs on a one-to-one basis (as for wireless client devices), and not about "binding multiple SSIDs to one VLAN" (from your post).

George

Multiple VLANS on a single SSID are not supported by the current software, you must assign each VLAN to it's own SSID.

the VLAN tags are in the packet headers between the Switch and the AP. Between the AP's or AP and client the SSID/VLAN pair determines the logical routing.

I hope this helps

Bill

"Multiple VLANS on a single SSID are not supported by the current software."

This is true for APs and SSIDs used to serve client devices. However, this is not true for bridge links. According to the same configuration guide you quoted earlier, "When you bridge, there is no need to associate a separate SSID with each VLAN." Cisco explicitly instructs you to use only a single SSID when *bridging* multiple VLANs.

http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#vlanbr

Again, I already know that this *does* work, I've got it in production on several customer networks. I want to know *how* it works. There's no concept of VLAN tagging in 802.11 as far as I know, so I want to know how one bridge device tells the other bridge device what VLAN a packet belongs to. If you don't know, that's okay, but that's the piece of information that I want to know.

My best guess is that as you have configured your AP's they are operating as a pure Layer 2 device for the bridge and as such do not examine the wired packets just encapsulate them into a wireless packet for the bridge and the AP on the other side remove the wireless encapsulation and forwards the packet to the wired network.

VLANS aare then handeled by the switches on either side of the bridge.

Hope this explanation holds water because it goes back to basic MAC layer bridging which appears to be what you are implementing.

this has been fun

Bill

scottmac
Advocate

I believe Bill has it pretty much nailed.

Keep in mind that "wireless bridging" is *not* part of the 802.11 standard and a manufacturer can make it work with elves and bunnies, if that's their chosen technology.

Because the devices also happen to be 802.11 APs, it just makes it easier to mutilate the existing protocols to gain that functionality.

(and probably a Good Thing, because the elves unions have tightened up their contract, and PETA is pitching a fit about servile bunnies for technological purposes).

That's why is it "difficult" (i.e., damn near impossible) to get wireless bridges (specifically bridges) from different vendors to inter-operate.

Straight-up L2 bridging (with adjustments for the dot1q) over proprietary link protocol sounds like a winner to me.

FWIW

Scott

Rob Huffman
Hall of Fame Community Legend

Hey Scott,

Perfect! 5 points for making my day with this wonderful answer :)

Take care my friend!

Rob

Thanks :)

I tend wax technical

Bill

I want to know specifically how Cisco bridges multiple VLANs on a single SSID on the 1300 series outdoor wireless bridges (at least). In fact, this is precisely what I asked in the post that started this thread. If they fully encapsulate 802.1q-tagged 802.3 packets inside 802.11 packets, then that's what I want to know. If they add a proprietary field to the 802.11 header, then that's what I want to know. It's not "elves and bunnies."

Content for Community-Ad