09-15-2022 08:10 AM
Buenos dias comunidad!
En esta oportunidad vengo a solicitarle de su ayuda en lo siguiente: No puedo conectarme a la WebGui. Desde las opciones del APP via comando pude constatar que la opción de Web GUi está habilitado tanto para HTTP como HTTPS, sin embargo, no puedo acceder.
Pensando que era algo de mi firewall/router principal, cree una regla que habilita la conexion al AP sin filtros ni nada, pero el caso es que sigue igual. Ya he reiniciado el AP pero igual.
show version
AP Running Image : 8.5.151.0
Primary Boot Image : 8.5.151.0
Backup Boot Image : 8.2.151.0
AP Image type : MOBILITY EXPRESS IMAGE
AP Configuration : MOBILITY EXPRESS CAPABLE
2 Gigabit Ethernet interfaces
2 802.11 Radios
Radio Driver version : 9.0.5.5-W8964
Radio FW version : 9.1.8.1
NSS FW version : 2.4.26
Pero tengo otro problema adicional, queria mostrar el comando donde se muestra en la configuración que WEBMODE está habilitado pero no se que pasó porque ahora no me toma los comandos que antes yo usaba, por ejemplo el siguiente comando:
CiscoAP2800#config network webmode enable
^
% Invalid input detected at '^' marker.
CiscoAP2800#
Agradecería cualquier apoyo que me puedan dar al respecto.
09-15-2022 09:58 AM
>....Pero tengo otro problema adicional, queria mostrar el comando ...
Tenga (config network webmode enable) en cuenta que requiere un reinicio Si ha reiniciado el punto de acceso en el medio, verifique si el punto de acceso todavía está ejecutando la movilidad expresa (emita el comando show version nuevamente)
M.
09-15-2022 11:37 AM
Muchas gracias por tu tiempo en responder.
Disculpa, pero no entendí bien. El problema es que en el CLI no me permite ejecutar el comando, me indica lo siguiente:
CiscoAP2800>config network webmode enable
^
% Invalid input detected at '^' marker.
CiscoAP2800>
No se, es como si estuviera en un modo de configuración distinta. No he podido encontrar algo en internet que corrobore eso.
09-16-2022 02:34 AM
- Reboot the access point , then try again.
M.
09-19-2022 07:50 AM
Hi,
I already rebooted my AP many times but I cant access web mode.
thank u
09-19-2022 07:57 AM
CiscoAP2800#show running-config
AP Name : CiscoAP2800
Admin State : Enabled
AP Mode : FlexConnect
AP Submode : None
Location : Floor Ground
Reboot Reason : Reload command
Primary controller name :
Primary controller IP :
Secondary controller name :
Secondary controller IP :
Tertiary controller name :
Tertiary controller IP :
AP join priority : 1
IP Prefer-mode : IPv4
CAPWAP UDP-Lite : Unconfigured
Last Joined Controller name: SU_AP2800
DTLS Encryption State : Disabled
Discovery Timer : 10
Heartbeat Timer : 30
CDP State : Enabled
Watchdog monitoring : Enabled
IOX : Disabled
RRM State : Enabled
LSC State : Disabled
SSH State : Enabled
AP Username : it
Session Timeout : 300
Extlog Host : 0.0.0.0
Extlog Flags : 0
Extlog Status Interval : 0
Syslog Host : 255.255.255.255
Syslog Facility : 0
Syslog Level : errors
Core Dump TFTP IP Addr :
Core Dump File Compression : Disabled
Core Dump Filename :
Client Trace Status : Enabled(All)
Client Trace All Clients : Enabled
Client Trace Filter : 0x0E000000
Client Trace Out ConsoleLog: Disabled
WLC Link LAG status : Disabled
AP Link LAG status : Disabled
AP WSA Mode : Disabled
CiscoAP2800#config network webmode enable
^
% Invalid input detected at '^' marker.
CiscoAP2800#enable
Por algun motivo ese comando me sigue sin aplicar.
Yo tengo dos AP, uno es un 2800 y el otro 3800, será que este quedo como "esclavo" del otro? por que al que estoy configurando es el 2800, al 3800 le perdí el rastro.
09-16-2022 04:56 AM
@Marcelo306 necesitas primero entrar en modo privilegiado con el comando "enable" para poder utilizar comandos avanzados.
09-19-2022 07:54 AM
Gracias!!!
Era eso. La verdad tengo muy poca experiencia con estos devices Cisco y me pierdo. Ahora si puedo aplicar los comandos.
09-17-2022 05:38 AM - edited 09-17-2022 05:39 AM
enable mode only applies if the AP is in CAPWAP mode so that is the first thing to ascertain...
- try "show ver"
- try "show sysinfo"
depending on the output tells you whether the AP is in CAPWAP or ME mode.
If it's in CAPWAP mode (most likely if the commands aren't working anymore then you need to switch back to ME mode:
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/82/user_guide/b_ME_User_Guide_82/m_appendix.html#task_330D7AD89F974001BEF10985059485DF
ap-type mobility-express tftp://<tftp server ip-address>/<filename of ap1g4 TAR file with path from root on the TFTP server>
If the AP is already running ME capable image it should switch without downloading the image again.
09-19-2022 07:58 AM
Thanks for your replay,
Yes, now with that command "enable" I can apply more commands.
In my case, the command that works is SHOW VERSION
09-22-2022 01:24 PM
For some reason, the Mobility Express console change its IP.
Now I can access mobility express console on SSH.
SO, I apply the command: show network summary:
(Cisco Controller) >show network summary
RF-Network Name............................. SU_AP2800
DNS Server IP1.............................. 10.130.0.155
DNS Server IP2.............................. 8.8.8.8
DNS Server IP3.............................. 208.67.222.222
DNS Server IP4.............................. 208.67.220.220
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode SSL Protocol................ Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Secure Shell (ssh) Cipher-Option High....... Disable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
IPv4 AP Multicast/Broadcast Mode............ Multicast Address : 0.0.0.0
IPv6 AP Multicast/Broadcast Mode............ Multicast Address : ::
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
the problem persist, I cant access webmode in HTTP or HTTPS.
What else I have to check?
thnak
09-22-2022 04:38 PM
I recommend reset to factory default then start your config from the beginning again.clear config
Then "reset system" - do not save config when you reset - or power off/on.
09-23-2022 05:39 AM
Thank a lot.
So, let me apply that and then I will tell you how was it.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide