cancelar
Mostrando los resultados de 
Buscar en lugar de 
Quiere decir: 
cancel
2044
Visitas
5
ÚTIL
40
Respuestas

Problema de coneccion AP18321

Saludos a todos en la Comunidad Cisco, les quiero comentar brevemente mi problema, en la empresa donde trabajo poseemos 2 AP Cisco modelo 18321, 1 de ellos presenta fallas la cual lo deja fuera de servio unos minutos.. El indicador LED cambia entre Ambar-Rojo-Verde por un periodo de tiempo hasta que se desconecta el cable, esta conectado por POE al menos unos 40mts del switch.

 

Gracias por leer este mensaje, saludos!!

40 RESPUESTAS 40

@juliodaniel76630 

Tienes dos opciones:

1. El contexto del WLC lo vuleve a configurar y a la IP de administración le asignas un segmento 192.168.0.X

2.- Al AP con  IP 192.168.0.89 le asignas una IP del segmento 172.16.1.X

 

Como te decia en el post anterior, el AP Master (el que esta corriendo el Software WLC) y el modo de AP, deben de subsistir en el mismo segmento de red. En tu caso, los tienen en diferentes segmentos, entonces, puedes optar por una de las dos acciones que te mencioné arriba, en cualquiera de ellas lograrás el objetivo de que ambos "equipos" esten en el mismo contexto

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**

Buenos dias Daniel, como hago para cambiar la IP de mi WLC actualmente es 172.16.1.20 y quiero colocarle 192.168.0.87 y asi los 2 AP queden todos en el mismo segmento de red AP-1 192.168.0.89  y AP-2 192.168.0.90 gateway 192.168.0.1

Hola @juliodaniel76630 

Dentro del contexto del WLC via CLI:

config interface address management 192.168.0.87 <Mask> <IP GATEWAY>
config interface vlan management <VLAN>

 

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**

Hola @juliodaniel76630 

 

config interface address management  192.168.0.87 <mascara> 192.168.0.1
config interface vlan management <vlan-id> 

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"

**Please rate the answer if this information was useful***

**Por favor si la información fue util marca esta respuesta como correcta**

*Tu reconocimiento nos alienta a seguir participando en los foros *

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**

Estimado daniel, me sale este mensaje Request failed - Active WLAN using interface. Disable WLAN first.

@juliodaniel76630

ejecuta el comando

config wlan disable <id WLAN>

Para saber el ID de la red puedes hacer un:

show wlan summary

Después de deshabilitar la red ejecuta los comandos del cambio de direccionamiento

 

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"

**Please rate the answer if this information was useful***

**Por favor si la información fue util marca esta respuesta como correcta**

*Tu reconocimiento nos alienta a seguir participando en los foros *

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**

Buenos días Daniel Saludos Ya coloque la Controladora y los AP dentro de la misma Red pero hoy uno de los AP me dio fallas en su servicio, te anexo los Logs correspondientes a ese AP:

Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0599]
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0699] PATH_MTU_PAYLOAD: encodelen = 259
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0699] PATH_MTU_PAYLOAD: slotId = 0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0699] PATH_MTU_PAYLOAD: slotId = 0 pktlen 1485 capwap_size 1360 met->encodeLen 259 pmtu_size 1080 pktlen 1485 loca lLength 1085
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0699] PATH_MTU_PAYLOAD: slotId = 0 len 1485(1085)
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0699] Sending Join Request Path MT U payload, Length 1360
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0699]
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799] Join Response from 192.168.0 .87
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799] AC accepted join request wit h result code: 0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799]
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799] PMTU : Setting MTU to : 1485
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799]
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799] Starting Post Join timer
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799] CAPWAP State: Image Data.
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0799]
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0899] AP current image version 8.2 .100.0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0899] Controller current image ver sion 8.2.100.0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0899] AP running image version 8.2 .100.0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0899] Version is the same, do not need update.
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0899] CAPWAP State: Configure.
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.0899]
Oct 25 14:34:46 syslog: +ethtool wired0
Oct 25 14:34:46 syslog: +ethtool wired0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.1499] ethtool wired0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.1499] ethtool wired0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.1899] PATH_MTU_PAYLOAD: encodelen = 2694
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.1899] PATH_MTU_PAYLOAD: slotId = 0
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.1899] PATH_MTU_PAYLOAD: slotId = 0 len 1485(5)
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.1999] Configuration Status sent to 192.168.0.87
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.6898] Discarding msg type 9 in CAP WAP state: 8.
Oct 25 14:34:46 kernel: [*10/25/2019 14:34:46.6998] Discarding msg type 9 in CAP WAP state: 8.
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.0690] Configuration Status Respons e from 192.168.0.87
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.0990] DOT11_DRV[0]: vendor_stop_ra dio Stop Radio0
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.0990] DOT11_DRV[0]: vendor_start_r adio Start Radio0
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.0990] ol_ath_set_channel set chann el freq 2462
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1090] DOT11_DRV[0]: vendor_stop_ra dio Stop Radio0
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1290] DOT11_DRV[0]: vendor_start_r adio Start Radio0
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1290] ol_ath_set_channel set chann el freq 2462
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1290] DOT11_DRV[1]: vendor_stop_ra dio Stop Radio1
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1390] DOT11_DRV[1]: vendor_start_r adio Start Radio1
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1390] ol_ath_set_channel set chann el freq 5180
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1590] DOT11_DRV[1]: vendor_stop_ra dio Stop Radio1
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1690] DOT11_DRV[1]: vendor_start_r adio Start Radio1
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1690] ol_ath_set_channel set chann el freq 5180
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1690] DOT11_DRV[1]: vendor_stop_ra dio Stop Radio1
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1690] DOT11_DRV[1]: vendor_start_r adio Start Radio1
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1690] ol_ath_set_channel set chann el freq 5180
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.1790] [DP] Setting up capwap datap ath
Oct 25 14:34:49 syslog: +ifconfig wired0 promisc
Oct 25 14:34:49 syslog: +ifconfig wired1 promisc down
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2190] CAPWAP data tunnel UPDATE to forwarding SUCCEEDED
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290] CAPWAP State: Run.
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290]
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290] CAPWAP State: Run.
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290]
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290] CAPWAP moved to RUN state st opping post join timer
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290] [DP] Setting up capwap datap ath
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290] [DP] No update to DP as ther e are no changes in fwd params
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2290] CAPWAP data tunnel ADD to fo rwarding SUCCEEDED
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2790] Change State Event Response from C0A80057
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.2790] BAD TLV ENTRY
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.3589] Change State Event Response from C0A80057
Oct 25 14:34:49 kernel: [*10/25/2019 14:34:49.3689] Change State Event Response from C0A80057
Oct 25 14:35:03 kernel: [*10/25/2019 14:35:03.9644] TLV-DEC-ERR: cannot process TLV for TLV_EOGREDOMAINCONFIGPAYLOAD(670/0)
Oct 25 14:35:03 kernel: [*10/25/2019 14:35:03.9644] TLV-DEC-ERR: No CB for TLV_E OGREDOMAINCONFIGPAYLOAD(670)
Oct 25 14:35:03 kernel: [*10/25/2019 14:35:03.9644] VAP_PAYLOAD for slot 0 Pasta LaEspacial(1)
Oct 25 14:35:03 kernel: [*10/25/2019 14:35:03.9644] ol_ath_set_channel set chann el freq 2462
Oct 25 14:35:03 kernel: [*10/25/2019 14:35:03.9644] DOT11_DRV[0]: vendor_stop_ra dio Stop Radio0
Oct 25 14:35:04 kernel: [*10/25/2019 14:35:03.9944] DOT11_DRV[0]: vendor_start_r adio Start Radio0
Oct 25 14:35:04 kernel: [*10/25/2019 14:35:03.9944] ol_ath_set_channel set chann el freq 2462
Oct 25 14:35:15 kernel: [*10/25/2019 14:35:15.8607] VAP_PAYLOAD for slot 1 Pasta LaEspacial(1)
Oct 25 14:35:15 kernel: [*10/25/2019 14:35:15.8707] ol_ath_set_channel set chann el freq 5180
Oct 25 14:35:15 kernel: [*10/25/2019 14:35:15.8707] DOT11_DRV[1]: vendor_stop_ra dio Stop Radio1
Oct 25 14:35:15 kernel: [*10/25/2019 14:35:15.8907] DOT11_DRV[1]: vendor_start_r adio Start Radio1
Oct 25 14:35:15 kernel: [*10/25/2019 14:35:15.8907] ol_ath_set_channel set chann el freq 5180
Oct 25 14:35:36 kernel: [*10/25/2019 14:35:36.8141]
Oct 25 14:35:36 kernel: [*10/25/2019 14:35:36.8141] Last crash log /var/log/cras h_log uploaded to controller.
Oct 25 14:35:36 kernel: [*10/25/2019 14:35:36.8141]
Oct 25 14:36:50 kernel: [*10/25/2019 14:36:50.7010] Re-Tx Count=11, Max Re-Tx Va lue=10, NumofPendingMsgs=18
Oct 25 14:36:50 kernel: [*10/25/2019 14:36:50.7010]
Oct 25 14:38:09 kernel: [*10/25/2019 14:38:09.4464] vap-0: Dropping Action frame before add_client for node e9f56000
Oct 25 14:38:39 kernel: [*10/25/2019 14:38:39.7076] vap-0: Dropping Action frame before add_client for node ebed0000
Oct 25 14:49:33 kernel: [*10/25/2019 14:49:33.6351] vap-0: Dropping Action frame before add_client for node ea853000

 

Agradezco toda la ayuda que me das, saludos Crack!!

 

a que te refieres con conectados a la misma red? 

tiene IP en la misma subnet? 

estan conectados al mismo switch? 

 

Dudo mucho que la perdida del WLC sea por cantidad de trafico que pasa el AP 

Saludos,
Rafael - TAC

Saludos Estimado, aqui te adjunto los logs del AP que me dio error el dia de hoy.

estas usando el ME como DHCP server?

Saludos,
Rafael - TAC

Buenos dias Estimado no, el DHCP lo otorga mi Fortigate E50 los AP no dan otorgan IP
Vamos a comenzar

¡Conecte con otros expertos de Cisco y del mundo! Encuentre soluciones a sus problemas técnicos o comerciales, y aprenda compartiendo experiencias.

Queremos que su experiencia sea grata, le compartimos algunos links que le ayudarán a familiarizarse con la Comunidad de Cisco: